Re: [hylafax-users] More then 12 redials ?

[Darren Nickerson <darren.nickerson@xxxxxxxx>]

Please try placing MaxDials etc into the server config file. Note that config instructions with a '1' superscript are used only by the HylaFAX scheduler process, and should appear in the config file, not the per-device config.devid file.

-Darren

On Sep 22, 2010, at 4:51 AM, Eliran Itzhak wrote:

Here's config
LogFacility:        daemon
CountryCode:        1
AreaCode:        415
LongDistancePrefix:    1
InternationalPrefix:    011
DialStringRules:    etc/dialrules
ServerTracing:        1
ModemGroup:        "any:\(ttyS.*\|ttyD.*\|ttyACM.*\)"
ModemGroup:        "ANY:\(ttyS.*\|ttyD.*\|ttyACM.*\)"
ModemGroup:        "HOT:\(ttyS10\|ttyS11\|ttyS12\|ttyS13\|ttyS14\|ttyS15\|ttyS16\|ttyS17\|ttyS4\|ttyS6\|ttyS7\|ttyS8\|ttyS9\|ttyD.*\)"
ModemGroup:        "BEZEQ:ttyS0"
ModemGroup:        "SUPRANEW:\(ttyS4\|ttyS5\|ttyS13\|ttyS14\|ttyS16\|ttyS17\)"
ModemGroup:        "LIMIT:\(ttyD.*\|ttyS4\|tty5\|ttyS6\|ttyS7\|ttyS8\|ttyS9\|ttyS10\|ttyS11\|ttyS12\)"

UseJobTSI:yes

Here's a sample config.tty file
CountryCode:        972
AreaCode:        077
FAXNumber:        "SUPRA-NEW-INTL"
LongDistancePrefix:    1
InternationalPrefix:    011
DialStringRules:    etc/dialrules
ServerTracing:        1
SessionTracing:        11
RecvFileMode:        0600
LogFileMode:        0600
DeviceMode:        0600
RingsBeforeAnswer:    1
SpeakerVolume:        "OFF"
GettyArgs:        "-h %l dx_%s"
LocalIdentifier:    "FreeFax.co.il"
TagLineFont:        etc/lutRS18.pcf
TagLineFormat:        "From %%l|%c|Page %%P of %%T"
MaxRecvPages:        25
ModemPriority:          100
#ModemReadyState:        B               # This can be Ready os Busy
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:        Class1        # use this to supply a hint
ModemRate:        115200        # rate for DCE-DTE communication
ModemFlowControl:    rtscts        # default
#
ModemNoFlowCmd:        AT&K0        # setup no flow control
ModemHardFlowCmd:    AT&K3        # setup hardware flow control
ModemSoftFlowCmd:    AT&K4        # setup software flow control
ModemSetupDTRCmd:    AT&D2        # setup so DTR drop resets modem
ModemSetupDCDCmd:    AT&C1        # setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd:    !Rockwell
ModemModelQueryCmd:    !RC288DPi
ModemRevQueryCmd:    ATI3        # product information
#
ModemDialCmd:        ATDT%s        # T for tone dialing

JobReqBusy: 30
JobReqNoAnswer: 60
JobReqNoCarrier: 30
JobReqNoFCon: 30
JobReqOther: 30
JobReqProto: 30

JobRetryBusy:20
JobRetryDataConn:20
JobRetryNoAnswer:20
JobRetryNoCarrier:20
JobRetryOther:20

MaxDials:50
MaxTries:50

2010/9/22 Lee Howard <faxguy@xxxxxxxxxxxxxxxx>

Please show me your /var/spool/hylafax/etc/config file.

Thanks,

Lee.


Eliran Itzhak wrote:

I really appreciate you going into the code to verify this, but I cant find any limit on the dialing attempts. the config / config.tty* file are fine. Where else can I look ?

Eliran.

2010/9/21 Lee Howard <faxguy@xxxxxxxxxxxxxxxx <mailto:faxguy@xxxxxxxxxxxxxxxx>>

   Eliran Itzhak wrote:

       ntries:0
       ndials:12
       totdials:12
       maxdials:20
       tottries:0
       maxtries:20

       errorcode:E333
       status:REJECT: Too many attempts to dial : 12, max 12


   There is only one place in the code where this error can happen
   (which is in faxQueueApp.c++)...

                 u_short maxdials = fxmin((u_short)
   job.getJCI().getMaxDials(),req->maxdials);
                 if (req->totdials >= maxdials) {
                     rejectJob(job, *req, fxStr::format(
                         "REJECT: Too many attempts to dial {E333}:
   %u, max %u",
                         req->totdials, maxdials));
                     deleteRequest(job, req, Job::rejected, true);
                     continue;
                 }

   So in order for the REJECT failure to have occurred the totdials
   would need to exceed maxdials (in the q-file) or the MaxDials
   value from JobControl.  Since it's clear from your q-file that
   totdials was less than maxdials, I must conclude, therefore, that
   you've got a MaxDials value of 12 coming out of JobControl.

   Is that correct?

   Thanks,

   Lee.