Re: [hylafax-users] Still "no response to PPS"

To: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] Still "no response to PPS"
From: Bernardo Volpi <bernardo.volpi@xxxxxxxxxxxxxxxxx>
Date: Wed, 28 Apr 2010 17:30:56 +0200

Il 28/04/2010 14:48, Lee Howard ha scritto:

Looking at the log you provided it appears that, at least with the Cirrus Logic modem, you're experiencing a lot of audio demodulation problems. Perhaps the audio is corrupt? Are you using VoIP? Ultimately the session failure occurs due to a modem fault:

apr 28 11:05:28.62: [ 9245]: <-- [10:AT+FTM=96\r] apr 28 11:05:28.64: [ 9245]: --> [7:CONNECT] apr 28 11:05:28.64: [ 9245]: <-- data [1026] apr 28 11:05:28.64: [ 9245]: <-- data [598] apr 28 11:05:28.64: [ 9245]: <-- data [2] apr 28 11:05:30.36: [ 9245]: --> [1:] apr 28 11:05:30.36: [ 9245]: SEND end page apr 28 11:05:30.36: [ 9245]: Unspecified Transmit Phase C error
Note that the modem responded with 0x11. Is that part of XON/XOFF? It's possible that the modem is doing software flow-control and you have it set for hardware. Change from "rtscts" to "xonxoff" and see if you fare better.

Hi Lee,

thanks for the efforts.
I uncommented
ModemFlowControl: xonxoff
in /var/spool/hylafax/etc/config.ttyS1 and restarted the service.

Now errors are earlier (I got two different, with same number). It seems modems can't talk.

I'm really sad :(

Any other idea?

Thanksss!!!!

Bernardo

apr 28 17:20:10.08: [11429]: SESSION BEGIN 000000450 3967922356 apr 28 17:20:10.08: [11429]: HylaFAX (tm) Version 6.0.3 apr 28 17:20:10.08: [11429]: SEND FAX: JOB 5 DEST 067922356 COMMID 000000450 DEVICE '/dev/ttyS1' FROM 'benfox <bernardo.volpi@xxxxxxxxxxxxxxxxx>' USER publica apr 28 17:20:10.08: [11429]: <-- [12:AT+FCLASS=1\r] apr 28 17:20:10.22: [11429]: --> [2:OK] apr 28 17:20:10.22: [11429]: DIAL 067922356 apr 28 17:20:10.22: [11429]: <-- [14:ATDT067922356\r] apr 28 17:20:32.33: [11429]: --> [7:CONNECT] apr 28 17:20:33.62: [11429]: --> [2:OK] apr 28 17:20:33.62: [11429]: REMOTE NSF "BC 53 01 60 12 0B 00" apr 28 17:20:33.62: [11429]: NSF remote fax equipment: Minolta apr 28 17:20:33.62: [11429]: <-- [9:AT+FRH=3\r] apr 28 17:20:33.64: [11429]: --> [7:CONNECT] apr 28 17:20:34.32: [11429]: --> [2:OK] apr 28 17:20:34.32: [11429]: REMOTE CSI "067922356" apr 28 17:20:34.32: [11429]: <-- [9:AT+FRH=3\r] apr 28 17:20:34.34: [11429]: --> [7:CONNECT] apr 28 17:20:34.75: [11429]: --> [2:OK] apr 28 17:20:34.75: [11429]: REMOTE best rate 14400 bit/s apr 28 17:20:34.75: [11429]: REMOTE max A4 page width (215 mm) apr 28 17:20:34.75: [11429]: REMOTE max unlimited page length apr 28 17:20:34.75: [11429]: REMOTE best vres 200 x 400 dpi apr 28 17:20:34.75: [11429]: REMOTE format support: MH, MR, MMR, JBIG apr 28 17:20:34.75: [11429]: REMOTE supports T.30 Annex A, 256-byte ECM apr 28 17:20:34.75: [11429]: REMOTE best 5 ms/scanline apr 28 17:20:34.75: [11429]: USE 14400 bit/s apr 28 17:20:34.75: [11429]: USE error correction mode apr 28 17:20:34.75: [11429]: SEND file "docq/doc5.ps;f1" apr 28 17:20:34.75: [11429]: USE A4 page width (215 mm) apr 28 17:20:34.75: [11429]: USE unlimited page length apr 28 17:20:34.75: [11429]: USE 7.7 line/mm apr 28 17:20:34.75: [11429]: USE 2-D MMR apr 28 17:20:34.75: [11429]: USE 0 ms/scanline apr 28 17:20:34.75: [11429]: SEND training at v.17 14400 bit/s apr 28 17:20:34.75: [11429]: <-- [9:AT+FRS=7\r] apr 28 17:20:35.12: [11429]: --> [2:OK] apr 28 17:20:35.12: [11429]: <-- [9:AT+FTH=3\r] apr 28 17:20:35.34: [11429]: --> [7:CONNECT] apr 28 17:20:35.34: [11429]: <-- data [23] apr 28 17:20:35.34: [11429]: <-- data [2] apr 28 17:20:36.98: [11429]: --> [7:CONNECT] apr 28 17:20:36.98: [11429]: <-- data [7] apr 28 17:20:36.98: [11429]: <-- data [2] apr 28 17:20:37.46: [11429]: --> [2:OK] apr 28 17:20:37.46: [11429]: <-- [9:AT+FTS=7\r] apr 28 17:20:37.54: [11429]: --> [2:OK] apr 28 17:20:37.54: [11429]: <-- [11:AT+FTM=145\r] apr 28 17:20:37.55: [11429]: --> [7:CONNECT] apr 28 17:20:37.55: [11429]: <-- data [1024] apr 28 17:20:37.55: [11429]: <-- data [1024] apr 28 17:20:37.55: [11429]: <-- data [652] apr 28 17:20:37.55: [11429]: <-- data [2] apr 28 17:20:39.70: [11429]: --> [1:] apr 28 17:20:39.70: [11429]: --> [2:OK] apr 28 17:20:39.70: [11429]: <-- [9:AT+FRH=3\r] apr 28 17:20:41.78: [11429]: --> [7:CONNECT] apr 28 17:20:42.88: [11429]: --> [2:OK] apr 28 17:20:42.88: [11429]: SEND training at v.17 12000 bit/s apr 28 17:20:42.88: [11429]: <-- [9:AT+FRS=7\r] apr 28 17:20:43.24: [11429]: --> [2:OK] apr 28 17:20:43.24: [11429]: <-- [9:AT+FTH=3\r] apr 28 17:20:43.46: [11429]: --> [7:CONNECT] apr 28 17:20:43.46: [11429]: <-- data [23] apr 28 17:20:43.46: [11429]: <-- data [2] apr 28 17:20:45.10: [11429]: --> [7:CONNECT] apr 28 17:20:45.10: [11429]: <-- data [7] apr 28 17:20:45.10: [11429]: <-- data [2] apr 28 17:20:45.58: [11429]: --> [2:OK] apr 28 17:20:45.58: [11429]: <-- [9:AT+FTS=7\r] apr 28 17:20:45.66: [11429]: --> [2:OK] apr 28 17:20:45.66: [11429]: <-- [11:AT+FTM=121\r] apr 28 17:20:45.67: [11429]: --> [7:CONNECT] apr 28 17:20:45.67: [11429]: <-- data [1024] apr 28 17:20:45.67: [11429]: <-- data [1024] apr 28 17:20:45.67: [11429]: <-- data [202] apr 28 17:20:45.67: [11429]: <-- data [2] apr 28 17:20:47.58: [11429]: --> [2:OK] apr 28 17:20:47.58: [11429]: <-- [9:AT+FRH=3\r] apr 28 17:20:48.29: [11429]: --> [7:CONNECT] apr 28 17:20:49.40: [11429]: --> [2:OK] apr 28 17:20:49.40: [11429]: SEND training at v.29 9600 bit/s apr 28 17:20:49.40: [11429]: <-- [9:AT+FRS=7\r] apr 28 17:20:49.76: [11429]: --> [2:OK] apr 28 17:20:49.76: [11429]: <-- [9:AT+FTH=3\r] apr 28 17:20:49.98: [11429]: --> [7:CONNECT] apr 28 17:20:49.98: [11429]: <-- data [23] apr 28 17:20:49.98: [11429]: <-- data [2] apr 28 17:20:51.62: [11429]: --> [7:CONNECT] apr 28 17:20:51.62: [11429]: <-- data [7] apr 28 17:20:51.62: [11429]: <-- data [2] apr 28 17:20:52.10: [11429]: --> [2:OK] apr 28 17:20:52.10: [11429]: <-- [9:AT+FTS=7\r] apr 28 17:20:52.18: [11429]: --> [2:OK] apr 28 17:20:52.18: [11429]: <-- [10:AT+FTM=96\r] apr 28 17:20:52.19: [11429]: --> [7:CONNECT] apr 28 17:20:52.19: [11429]: <-- data [1024] apr 28 17:20:52.19: [11429]: <-- data [776] apr 28 17:20:52.19: [11429]: <-- data [2] apr 28 17:20:54.08: [11429]: --> [1:] apr 28 17:20:54.08: [11429]: --> [2:OK] apr 28 17:20:54.08: [11429]: <-- [9:AT+FRH=3\r] apr 28 17:20:57.18: [11429]: --> [0:] apr 28 17:20:57.18: [11429]: MODEM <Empty line> apr 28 17:20:57.18: [11429]: <-- data [1] apr 28 17:20:57.18: [11429]: --> [2:OK] apr 28 17:20:57.18: [11429]: <-- [9:AT+FRS=7\r] apr 28 17:20:57.26: [11429]: --> [2:OK] apr 28 17:20:57.26: [11429]: SEND training at v.29 7200 bit/s apr 28 17:20:57.26: [11429]: <-- [9:AT+FTH=3\r] apr 28 17:20:57.48: [11429]: --> [7:CONNECT] apr 28 17:20:57.48: [11429]: <-- data [23] apr 28 17:20:57.48: [11429]: <-- data [2] apr 28 17:20:59.12: [11429]: --> [7:CONNECT] apr 28 17:20:59.12: [11429]: <-- data [7] apr 28 17:20:59.12: [11429]: <-- data [2] apr 28 17:20:59.60: [11429]: --> [2:OK] apr 28 17:20:59.60: [11429]: <-- [9:AT+FTS=7\r] apr 28 17:20:59.68: [11429]: --> [2:OK] apr 28 17:20:59.68: [11429]: <-- [10:AT+FTM=72\r] apr 28 17:20:59.69: [11429]: --> [7:CONNECT] apr 28 17:20:59.69: [11429]: <-- data [1024] apr 28 17:20:59.69: [11429]: <-- data [326] apr 28 17:20:59.69: [11429]: <-- data [2] apr 28 17:21:01.58: [11429]: --> [2:] apr 28 17:21:01.58: [11429]: --> [2:OK] apr 28 17:21:01.58: [11429]: <-- [9:AT+FRH=3\r] apr 28 17:21:04.68: [11429]: --> [0:] apr 28 17:21:04.68: [11429]: MODEM <Empty line> apr 28 17:21:04.68: [11429]: <-- data [1] apr 28 17:21:04.68: [11429]: --> [2:OK] apr 28 17:21:04.68: [11429]: <-- [9:AT+FRS=7\r] apr 28 17:21:04.76: [11429]: --> [2:OK] apr 28 17:21:04.76: [11429]: SEND training at v.27ter 4800 bit/s apr 28 17:21:04.76: [11429]: <-- [9:AT+FTH=3\r] apr 28 17:21:04.98: [11429]: --> [7:CONNECT] apr 28 17:21:04.98: [11429]: <-- data [23] apr 28 17:21:04.98: [11429]: <-- data [2] apr 28 17:21:06.62: [11429]: --> [7:CONNECT] apr 28 17:21:06.62: [11429]: <-- data [7] apr 28 17:21:06.62: [11429]: <-- data [2] apr 28 17:21:07.10: [11429]: --> [2:OK] apr 28 17:21:07.10: [11429]: <-- [9:AT+FTS=7\r] apr 28 17:21:07.18: [11429]: --> [2:OK] apr 28 17:21:07.18: [11429]: <-- [10:AT+FTM=48\r] apr 28 17:21:07.19: [11429]: --> [7:CONNECT] apr 28 17:21:07.19: [11429]: <-- data [900] apr 28 17:21:07.19: [11429]: <-- data [2] apr 28 17:21:09.76: [11429]: --> [2:OK] apr 28 17:21:09.76: [11429]: <-- [9:AT+FRH=3\r] apr 28 17:21:10.90: [11429]: --> [7:CONNECT] apr 28 17:21:12.00: [11429]: --> [2:OK] apr 28 17:21:12.00: [11429]: TRAINING failed apr 28 17:21:12.00: [11429]: SEND: Giving up after 3 attempts to send same page "docq/doc5.ps;f1", dirnum 0 apr 28 17:21:12.00: [11429]: <-- [9:AT+FRS=7\r] apr 28 17:21:12.26: [11429]: --> [2:OK] apr 28 17:21:12.26: [11429]: <-- [9:AT+FTH=3\r] apr 28 17:21:12.48: [11429]: --> [7:CONNECT] apr 28 17:21:12.48: [11429]: <-- data [3] apr 28 17:21:12.48: [11429]: <-- data [2] apr 28 17:21:13.72: [11429]: --> [2:OK] apr 28 17:21:14.72: [11429]: <-- [5:ATH0\r] apr 28 17:21:14.84: [11429]: --> [2:OK] apr 28 17:21:14.84: [11429]: SESSION END

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] Still "no response to PPS"
  - From: Lee Howard

References:
- [hylafax-users] Still "no response to PPS"
  - From: Bernardo Volpi
- Re: [hylafax-users] Still "no response to PPS"
  - From: Lee Howard
- Re: [hylafax-users] Still "no response to PPS"
  - From: Bernardo Volpi
- Re: [hylafax-users] Still "no response to PPS"
  - From: Lee Howard

Prev by Date: [hylafax-users] How to control where's the trouble with email
Next by Date: [hylafax-users] bin/notify not being executed
Previous by thread: Re: [hylafax-users] Still "no response to PPS"
Next by thread: Re: [hylafax-users] Still "no response to PPS"
Index(es):
- Main
- Thread

Project hosted by iFAX Solutions