Re: [hylafax-users] No response to PPS repeated 3 times.:

["Sundar K. Iyengar" <ski@xxxxxxx>]

I have the same problem.  But i am trying to send a fax to a Kyocera Mita
fax machine from Fedora 8 and a conexant softmodem.
I dont have this problem when I use CentOs 5 to the same fax destination.
I also have a multitech internal modem when I try to connect and send a fax
I get the following error
%%[ ProductName: GPL Ghos (no pages get sent)

here is the log for the softModem.
Thanks,
Jan 23 19:50:33.16: [22500]: SESSION BEGIN 000000032 xxxxxxxxxxx
Jan 23 19:50:33.16: [22500]: HylaFAX (tm) Version 4.4.2
Jan 23 19:50:33.16: [22500]: SEND FAX: JOB 10 DEST 1(xxx) xxx-xxxx COMMID
000000032 DEVICE '/dev/ttySHSF0' FROM 'faxuser <faxuser@xxxxxxxxxxx>' USER
faxuser
Jan 23 19:50:33.16: [22500]: <-- [12:AT+FCLASS=1\r]
Jan 23 19:50:33.19: [22500]: --> [2:OK]
Jan 23 19:50:33.19: [22500]: DIAL 1(xxx)xxxxxxx
Jan 23 19:50:33.19: [22500]: <-- [18:ATDT1(xxx)xxxx\r]
Jan 23 19:50:57.30: [22500]: --> [7:CONNECT]
Jan 23 19:50:58.47: [22500]: --> [2:OK]
Jan 23 19:50:58.47: [22500]: REMOTE NSF "00 00 66 01 18 0B B2 6A 10 00 00 00
00 00 00 24"
Jan 23 19:50:58.47: [22500]: NSF remote fax equipment: Utax/Mita
Jan 23 19:50:58.47: [22500]: <-- [9:AT+FRH=3\r]
Jan 23 19:50:58.50: [22500]: --> [7:CONNECT]
Jan 23 19:50:59.00: [22500]: --> [2:OK]
Jan 23 19:50:59.00: [22500]: REMOTE NSF "00 00 66 02 09 52 41 44 4E 55 53 20
52 44"
Jan 23 19:50:59.00: [22500]: NSF remote fax equipment: Utax/Mita
Jan 23 19:50:59.00: [22500]: NSF remote station ID: "DR SUNDAR"
Jan 23 19:50:59.00: [22500]: <-- [9:AT+FRH=3\r]
Jan 23 19:50:59.02: [22500]: --> [7:CONNECT]
Jan 23 19:50:59.70: [22500]: --> [2:OK]
Jan 23 19:50:59.70: [22500]: REMOTE CSI "xxxxxxxxxx"
Jan 23 19:50:59.70: [22500]: <-- [9:AT+FRH=3\r]
Jan 23 19:50:59.72: [22500]: --> [7:CONNECT]
Jan 23 19:51:00.16: [22500]: --> [2:OK]
Jan 23 19:51:00.16: [22500]: REMOTE best rate 33600 bit/s
Jan 23 19:51:00.16: [22500]: REMOTE max A3 page width (303 mm)
Jan 23 19:51:00.16: [22500]: REMOTE max unlimited page length
Jan 23 19:51:00.16: [22500]: REMOTE best vres 15.4 line/mm
Jan 23 19:51:00.16: [22500]: REMOTE format support: MH, MR, MMR, JBIG
Jan 23 19:51:00.16: [22500]: REMOTE supports T.30 Annex A, 256-byte ECM
Jan 23 19:51:00.16: [22500]: REMOTE best 10 ms, 5 ms/scanline
Jan 23 19:51:00.16: [22500]: USE 14400 bit/s
Jan 23 19:51:00.16: [22500]: USE error correction mode
Jan 23 19:51:00.16: [22500]: SEND file "docq/doc19.ps;31"
Jan 23 19:51:00.16: [22500]: USE A4 page width (215 mm)
Jan 23 19:51:00.16: [22500]: USE unlimited page length
Jan 23 19:51:00.16: [22500]: USE 7.7 line/mm
Jan 23 19:51:00.16: [22500]: USE 2-D MMR
Jan 23 19:51:00.16: [22500]: USE 0 ms/scanline
Jan 23 19:51:00.16: [22500]: SEND training at v.17 14400 bit/s
Jan 23 19:51:00.16: [22500]: <-- [9:AT+FRS=7\r]
Jan 23 19:51:00.31: [22500]: --> [2:OK]
Jan 23 19:51:00.31: [22500]: <-- [9:AT+FTH=3\r]
Jan 23 19:51:00.63: [22500]: --> [7:CONNECT]
Jan 23 19:51:00.63: [22500]: <-- data [23]
Jan 23 19:51:00.63: [22500]: <-- data [2]
Jan 23 19:51:02.20: [22500]: --> [7:CONNECT]
Jan 23 19:51:02.20: [22500]: <-- data [7]
Jan 23 19:51:02.20: [22500]: <-- data [2]
Jan 23 19:51:02.72: [22500]: --> [2:OK]
Jan 23 19:51:02.72: [22500]: <-- [9:AT+FTS=7\r]
Jan 23 19:51:02.87: [22500]: --> [2:OK]
Jan 23 19:51:02.87: [22500]: <-- [11:AT+FTM=145\r]
Jan 23 19:51:02.89: [22500]: --> [7:CONNECT]
Jan 23 19:51:02.89: [22500]: <-- data [1024]
Jan 23 19:51:02.89: [22500]: <-- data [1024]
Jan 23 19:51:02.89: [22500]: <-- data [652]
Jan 23 19:51:02.89: [22500]: <-- data [2]
Jan 23 19:51:06.05: [22500]: --> [2:OK]
Jan 23 19:51:06.05: [22500]: <-- [9:AT+FRH=3\r]
Jan 23 19:51:06.70: [22500]: --> [7:CONNECT]
Jan 23 19:51:07.99: [22500]: --> [2:OK]
Jan 23 19:51:07.99: [22500]: TRAINING succeeded
Jan 23 19:51:07.99: [22500]: SEND begin page
Jan 23 19:51:07.99: [22500]: Reading MH-compressed image file
Jan 23 19:51:08.00: [22500]: SEND EOFB
Jan 23 19:51:08.00: [22500]: SEND send frame number 0
Jan 23 19:51:08.00: [22500]: SEND send frame number 1
Jan 23 19:51:08.00: [22500]: SEND send frame number 2
Jan 23 19:51:08.00: [22500]: SEND send frame number 3
Jan 23 19:51:08.00: [22500]: SEND send frame number 4
Jan 23 19:51:08.00: [22500]: SEND send frame number 5
Jan 23 19:51:08.00: [22500]: SEND send frame number 6
Jan 23 19:51:08.00: [22500]: SEND send frame number 7
Jan 23 19:51:08.00: [22500]: SEND send frame number 8
Jan 23 19:51:08.00: [22500]: SEND send frame number 9
Jan 23 19:51:08.00: [22500]: SEND send frame number 10
Jan 23 19:51:08.00: [22500]: SEND send frame number 11
Jan 23 19:51:08.00: [22500]: SEND send frame number 12
Jan 23 19:51:08.00: [22500]: SEND send frame number 13
Jan 23 19:51:08.00: [22500]: SEND send frame number 14
Jan 23 19:51:08.00: [22500]: SEND send frame number 15
Jan 23 19:51:08.00: [22500]: SEND send frame number 16
Jan 23 19:51:08.00: [22500]: SEND send frame number 17
Jan 23 19:51:08.00: [22500]: SEND send frame number 18
Jan 23 19:51:08.00: [22500]: SEND send frame number 19
Jan 23 19:51:08.00: [22500]: SEND send frame number 20
Jan 23 19:51:08.00: [22500]: SEND send frame number 21
Jan 23 19:51:08.00: [22500]: SEND send frame number 22
Jan 23 19:51:08.00: [22500]: SEND send frame number 23
Jan 23 19:51:08.00: [22500]: SEND send frame number 24
Jan 23 19:51:08.00: [22500]: SEND send frame number 25
Jan 23 19:51:08.00: [22500]: SEND send frame number 26
Jan 23 19:51:08.00: [22500]: SEND send frame number 27
Jan 23 19:51:08.00: [22500]: SEND send frame number 28
Jan 23 19:51:08.00: [22500]: SEND send frame number 29
Jan 23 19:51:08.00: [22500]: SEND send frame number 30
Jan 23 19:51:08.00: [22500]: SEND send frame number 31
Jan 23 19:51:08.00: [22500]: SEND send frame number 32
Jan 23 19:51:08.00: [22500]: SEND send frame number 33
Jan 23 19:51:08.00: [22500]: SEND send frame number 34
Jan 23 19:51:08.00: [22500]: SEND send frame number 35
Jan 23 19:51:08.00: [22500]: <-- [9:AT+FRS=7\r]
Jan 23 19:51:08.13: [22500]: --> [2:OK]
Jan 23 19:51:08.13: [22500]: <-- [11:AT+FTM=146\r]
Jan 23 19:51:08.45: [22500]: --> [7:CONNECT]
Jan 23 19:51:08.45: [22500]: <-- data [1029]
Jan 23 19:51:08.45: [22500]: <-- data [1029]
Jan 23 19:51:08.45: [22500]: <-- data [1029]
Jan 23 19:51:08.45: [22500]: <-- data [1035]
Jan 23 19:51:08.45: [22500]: <-- data [1036]
Jan 23 19:51:08.45: [22500]: <-- data [1034]
Jan 23 19:51:08.45: [22500]: <-- data [1030]
Jan 23 19:51:08.45: [22500]: <-- data [1047]
Jan 23 19:51:09.40: [22500]: <-- data [1033]
Jan 23 19:51:09.40: [22500]: <-- data [1027]
Jan 23 19:51:10.55: [22500]: <-- data [152]
Jan 23 19:51:10.55: [22500]: <-- data [2]
Jan 23 19:51:14.65: [22500]: --> [2:OK]
Jan 23 19:51:14.65: [22500]: <-- [9:AT+FTS=9\r]
Jan 23 19:51:14.82: [22500]: --> [2:OK]
Jan 23 19:51:14.82: [22500]: <-- [9:AT+FTH=3\r]
Jan 23 19:51:14.85: [22500]: --> [7:CONNECT]
Jan 23 19:51:14.85: [22500]: <-- data [7]
Jan 23 19:51:14.85: [22500]: <-- data [2]
Jan 23 19:51:16.23: [22500]: --> [2:OK]
Jan 23 19:51:16.23: [22500]: SEND send PPS (partial page signal)
Jan 23 19:51:16.23: [22500]: SEND send EOP (no more pages or documents)
Jan 23 19:51:16.23: [22500]: <-- [9:AT+FRH=3\r]
Jan 23 19:51:16.38: [22500]: --> [7:CONNECT]
Jan 23 19:51:16.49: [22500]: --> [5:ERROR]
Jan 23 19:51:16.49: [22500]: MODEM Command error
Jan 23 19:51:16.49: [22500]: FCS error
Jan 23 19:51:16.49: [22500]: <-- [9:AT+FTH=3\r]
Jan 23 19:51:18.33: [22500]: --> [7:CONNECT]
Jan 23 19:51:18.33: [22500]: <-- data [7]
Jan 23 19:51:18.33: [22500]: <-- data [2]
Jan 23 19:51:19.73: [22500]: --> [2:OK]
Jan 23 19:51:19.73: [22500]: SEND send PPS (partial page signal)
Jan 23 19:51:19.73: [22500]: SEND send EOP (no more pages or documents)
Jan 23 19:51:19.73: [22500]: <-- [9:AT+FRH=3\r]
Jan 23 19:51:19.88: [22500]: --> [7:CONNECT]
Jan 23 19:51:20.00: [22500]: --> [5:ERROR]
Jan 23 19:51:20.00: [22500]: MODEM Command error
Jan 23 19:51:20.00: [22500]: FCS error
Jan 23 19:51:20.00: [22500]: <-- [9:AT+FTH=3\r]
Jan 23 19:51:21.84: [22500]: --> [7:CONNECT]
Jan 23 19:51:21.84: [22500]: <-- data [7]
Jan 23 19:51:21.84: [22500]: <-- data [2]
Jan 23 19:51:23.24: [22500]: --> [2:OK]
Jan 23 19:51:23.24: [22500]: SEND send PPS (partial page signal)
Jan 23 19:51:23.24: [22500]: SEND send EOP (no more pages or documents)
Jan 23 19:51:23.24: [22500]: <-- [9:AT+FRH=3\r]
Jan 23 19:51:23.39: [22500]: --> [7:CONNECT]
Jan 23 19:51:23.51: [22500]: --> [5:ERROR]
Jan 23 19:51:23.51: [22500]: MODEM Command error
Jan 23 19:51:23.51: [22500]: FCS error
Jan 23 19:51:23.51: [22500]: No response to PPS repeated 3 times.
Jan 23 19:51:23.51: [22500]: SEND end page
Jan 23 19:51:23.51: [22500]: SEND: Giving up after 3 attempts to send same
page "docq/doc19.ps;31", dirnum 0
Jan 23 19:51:23.51: [22500]: <-- [9:AT+FRS=7\r]
Jan 23 19:51:23.66: [22500]: --> [2:OK]
Jan 23 19:51:23.66: [22500]: <-- [9:AT+FTH=3\r]
Jan 23 19:51:25.36: [22500]: --> [7:CONNECT]
Jan 23 19:51:25.36: [22500]: <-- data [3]
Jan 23 19:51:25.36: [22500]: <-- data [2]
Jan 23 19:51:26.65: [22500]: --> [2:OK]
Jan 23 19:51:27.65: [22500]: <-- [5:ATH0\r]
Jan 23 19:51:27.78: [22500]: --> [2:OK]
Jan 23 19:51:27.78: [22500]: SESSION END

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of CS Linux Support
Group
Sent: Friday, January 25, 2008 12:38 PM
To: Daren Russell
Cc: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] No response to PPS repeated 3 times.:

Hi Daren and everyone,
     Thanks for the reply.I tried your approach and installed
hylafax-4.3.4 and tried faxing the document to Ricoh faxmachine but I got
the same error.I tried many subversions in 4.3 but still received the same
error.
      I didnt have any problem in sending faxes to Panasonic receivers in
all the Hylafax versions I have tried.
      This issue has already been reported(USR modem and a RICOH receiver
was used) in this forum in the following threads.
http://www.hylafax.org/archive/2006-05/msg00539.php
http://www.hylafax.org/archive/2004-06/msg00217.php
but no solution in specific was mentioned.The problem many suspect is in the
Ricoh firmware.
         Is this problem still being encountered by anyone and is there any
way to get around with this Ricoh firmware issue ?


Thank you all,
Aravindan


> CS Linux Support Group wrote:
>> Hi all,
>>      I am using a USR V.92 5686 FAXMODEM.I installed the latest 
>> version of hylafax server (hylafax-4.4.4).I was able to send and 
>> receive faxes
perfectly when the receiving faxmachine was a Panasonic model.
>>         But when the I tried sending a fax to the faxmachine of model 
>> ricoh I received the following error "No response to PPS repeated 3 
>> times.; Giving up after 3 attempts to
send".
>>      The faxsend requests were failing consistently when sent to a
ricoh
>> machine and the machine is only able to receive the fax cover sheet.
>>          I searched the mailing list for this issue and I did see 
>> postings on it but didn't find any specific reply fixing it.
>>         Is this issue specific to the USR modem and/or the Ricoh 
>> faxmachine ?
>> Thanking you all in advance.
>> Aravindan.
>
> Hi
>
> You're not alone with this.  I was about to compose a mail saying
exactly the same after upgrading from 4.3.4 to 4.4.4 on FreeBSD.
>
> We got the error from receivers who previously did not have a problem
with - and in spite of the error, they receive the fax OK, but then Hylafax
has another go at sending it!
>
> We're using a Diamond SupraExpress, so it's not specific to USR, and 
> we
tried both Class 1 and 1.0.
>
> I ended up downgrading again back to 4.3.4, and the problem went away.
>
> Regards
> Daren
>
>> The log I received when trying to send a fax to the ricoh faxmachine 
>> is as follows.
>> --------------------------------------------------------------------
>>> No response to PPS repeated 3 times.; Giving up after 3 attempts to 
>>> send
>> same page
>>>    ---- Transcript of session follows ---- Jan 22 16:13:32.66: 
>>> [11552]: SESSION BEGIN 000000097 121254640 Jan 22
16:13:32.66: [11552]: HylaFAX (tm) Version 4.4.2
>>> Jan 22 16:13:32.66: [11552]: SEND FAX: JOB 59 DEST 54640 COMMID
>> 000000097
>> DEVICE '/dev/ttyS0' FROM 'acase <acase@xxxxxxxxxxxx>' USER acase
>>> Jan 22 16:13:32.66: [11552]: <-- [12:AT+FCLASS=1\r] Jan 22 
>>> 16:13:32.80: [11552]: --> [2:OK] Jan 22 16:13:32.80: [11552]: DIAL 
>>> 54640 Jan 22 16:13:32.80: [11552]: <-- [10:ATDT54640\r] Jan 22 
>>> 16:13:44.11: [11552]: --> [7:CONNECT] Jan 22 16:13:45.59: [11552]: 
>>> --> [2:OK] Jan 22 16:13:45.59: [11552]: REMOTE NSF "00 00 25 00 00 
>>> 00 92 10 4D 02
>> 00 58
>> 00 28 00 A0 80 80 B1 60"
>>> Jan 22 16:13:45.59: [11552]: NSF remote fax equipment: Ricoh Jan 22 
>>> 16:13:45.59: [11552]: <-- [9:AT+FRH=3\r] Jan 22 16:13:45.60: 
>>> [11552]: --> [7:CONNECT] Jan 22 16:13:46.02: [11552]: --> [2:OK] Jan 
>>> 22 16:13:46.02: [11552]: REMOTE best rate 33600 bit/s Jan 22 
>>> 16:13:46.02: [11552]: REMOTE max A3 page width (303 mm) Jan 22
16:13:46.02: [11552]: REMOTE max unlimited page length
>>> Jan 22 16:13:46.02: [11552]: REMOTE best vres 200 x 200 dpi Jan 22 
>>> 16:13:46.02: [11552]: REMOTE format support: MH, MR, MMR, JBIG
>> Jan 22 16:13:46.02: [11552]: REMOTE supports T.30 Annex A, 256-byte 
>> ECM
Jan 22 16:13:46.02: [11552]: REMOTE best 10 ms/scanline
>>> Jan 22 16:13:46.02: [11552]: USE 14400 bit/s Jan 22 16:13:46.02: 
>>> [11552]: USE error correction mode Jan 22 16:13:46.02: [11552]: SEND 
>>> file "docq/cover59;f0"
>>> Jan 22 16:13:46.02: [11552]: USE A4 page width (215 mm) Jan 22 
>>> 16:13:46.02: [11552]: USE unlimited page length Jan 22 16:13:46.02: 
>>> [11552]: USE 3.85 line/mm Jan 22 16:13:46.02: [11552]: USE 2-D MMR 
>>> Jan 22 16:13:46.02: [11552]: USE 0 ms/scanline Jan 22 16:13:46.02: 
>>> [11552]: SEND training at v.17 14400 bit/s Jan 22
16:13:46.02: [11552]: DELAY 70 ms
>>> Jan 22 16:13:46.09: [11552]: <-- [9:AT+FTH=3\r] Jan 22 16:13:46.28: 
>>> [11552]: --> [7:CONNECT] Jan 22 16:13:46.28: [11552]: <-- data [23] 
>>> Jan 22 16:13:46.28: [11552]: <-- data [2] Jan 22 16:13:46.30: 
>>> [11552]: --> [7:CONNECT] Jan 22 16:13:46.30: [11552]: <-- data [7] 
>>> Jan 22 16:13:46.30: [11552]: <-- data [2] Jan 22 16:13:48.28: 
>>> [11552]: --> [2:OK] Jan 22 16:13:48.28: [11552]: <-- [9:AT+FTS=7\r] 
>>> Jan 22 16:13:48.36: [11552]: --> [2:OK] Jan 22 16:13:48.36: [11552]: 
>>> <-- [11:AT+FTM=145\r] Jan 22 16:13:49.84: [11552]: --> [7:CONNECT] 
>>> Jan 22 16:13:49.84: [11552]: <-- data [1024] Jan 22 16:13:49.84: 
>>> [11552]: <-- data [1024] Jan 22 16:13:49.84: [11552]: <-- data [652] 
>>> Jan 22 16:13:49.84: [11552]: <-- data [2] Jan 22 16:13:51.37: 
>>> [11552]: --> [2:OK] Jan 22 16:13:51.37: [11552]: <-- [9:AT+FRS=1\r] 
>>> Jan 22 16:13:51.39: [11552]: --> [2:OK] Jan 22 16:13:51.39: [11552]: 
>>> <-- [9:AT+FRH=3\r] Jan 22 16:13:52.56: [11552]: --> [7:CONNECT] Jan 
>>> 22 16:13:53.17: [11552]: --> [2:OK] Jan 22 16:13:53.17: [11552]: 
>>> TRAINING succeeded Jan 22 16:13:53.17: [11552]: SEND begin page Jan 
>>> 22 16:13:53.17: [11552]: SEND EOFB Jan 22 16:13:53.17: [11552]: SEND 
>>> send frame number 0 Jan 22 16:13:53.17: [11552]: SEND send frame 
>>> number 1 Jan 22 16:13:53.17: [11552]: SEND send frame number 2 Jan 
>>> 22 16:13:53.17: [11552]: SEND send frame number 3 Jan 22 
>>> 16:13:53.17: [11552]: SEND send frame number 4 Jan 22 16:13:53.17: 
>>> [11552]: SEND send frame number 5 Jan 22 16:13:53.17: [11552]: SEND 
>>> send frame number 6 Jan 22 16:13:53.17: [11552]: SEND send frame 
>>> number 7 Jan 22 16:13:53.17: [11552]: SEND send frame number 8 Jan 
>>> 22 16:13:53.17: [11552]: SEND send frame number 9 Jan 22 
>>> 16:13:53.17: [11552]: SEND send frame number 10 Jan 22 16:13:53.17: 
>>> [11552]: SEND send frame number 11 Jan 22 16:13:53.17: [11552]: SEND 
>>> send frame number 12 Jan 22 16:13:53.17: [11552]: SEND send frame 
>>> number 13 Jan 22 16:13:53.17: [11552]: DELAY 70 ms Jan 22 
>>> 16:13:53.24: [11552]: <-- [11:AT+FTM=146\r] Jan 22 16:13:53.50: 
>>> [11552]: --> [7:CONNECT] Jan 22 16:13:53.50: [11552]: <-- data 
>>> [1034] Jan 22 16:13:53.50: [11552]: <-- data [1037] Jan 22 
>>> 16:13:53.50: [11552]: <-- data [1041] Jan 22 16:13:53.50: [11552]: 
>>> <-- data [1031] Jan 22 16:13:55.49: [11552]: <-- data [49] Jan 22 
>>> 16:13:55.49: [11552]: <-- data [2] Jan 22 16:13:55.83: [11552]: --> 
>>> [2:OK] Jan 22 16:13:55.83: [11552]: <-- [9:AT+FTS=7\r] Jan 22 
>>> 16:13:55.91: [11552]: --> [2:OK] Jan 22 16:13:55.91: [11552]: <-- 
>>> [9:AT+FTH=3\r] Jan 22 16:13:56.06: [11552]: --> [7:CONNECT] Jan 22 
>>> 16:13:56.06: [11552]: <-- data [7] Jan 22 16:13:56.06: [11552]: <-- 
>>> data [2] Jan 22 16:13:57.34: [11552]: --> [2:OK] Jan 22 16:13:57.34: 
>>> [11552]: SEND send PPS (partial page signal) Jan
22
>> 16:13:57.34: [11552]: SEND send MPS (more pages, same document) Jan 
>> 22
16:13:57.34: [11552]: <-- [9:AT+FRH=3\r]
>>> Jan 22 16:13:57.71: [11552]: --> [10:NO CARRIER] Jan 22 16:13:57.71: 
>>> [11552]: MODEM No carrier Jan 22 16:13:57.71: [11552]: <-- 
>>> [9:AT+FTH=3\r] Jan 22 16:13:57.91: [11552]: --> [7:CONNECT] Jan 22 
>>> 16:13:57.91: [11552]: <-- data [7] Jan 22 16:13:57.91: [11552]: <-- 
>>> data [2] Jan 22 16:13:59.19: [11552]: --> [2:OK] Jan 22 16:13:59.19: 
>>> [11552]: SEND send PPS (partial page signal) Jan
22
>> 16:13:59.19: [11552]: SEND send MPS (more pages, same document) Jan 
>> 22
16:13:59.19: [11552]: <-- [9:AT+FRH=3\r]
>>> Jan 22 16:13:59.76: [11552]: --> [10:NO CARRIER] Jan 22 16:13:59.76: 
>>> [11552]: MODEM No carrier Jan 22 16:13:59.76: [11552]: <-- 
>>> [9:AT+FTH=3\r] Jan 22 16:13:59.95: [11552]: --> [7:CONNECT] Jan 22 
>>> 16:13:59.95: [11552]: <-- data [7] Jan 22 16:13:59.95: [11552]: <-- 
>>> data [2] Jan 22 16:14:01.24: [11552]: --> [2:OK] Jan 22 16:14:01.24: 
>>> [11552]: SEND send PPS (partial page signal) Jan
22
>> 16:14:01.24: [11552]: SEND send MPS (more pages, same document) Jan 
>> 22
16:14:01.24: [11552]: <-- [9:AT+FRH=3\r]
>>> Jan 22 16:14:01.71: [11552]: --> [10:NO CARRIER] Jan 22 16:14:01.71: 
>>> [11552]: MODEM No carrier Jan 22 16:14:01.71: [11552]: No response 
>>> to PPS repeated 3 times. Jan 22
>> 16:14:01.71: [11552]: SEND end page
>>> Jan 22 16:14:01.71: [11552]: SEND: Giving up after 3 attempts to 
>>> send
>> same
>> page "docq/cover59;f0", dirnum 0
>>> Jan 22 16:14:01.71: [11552]: DELAY 70 ms Jan 22 16:14:01.79: 
>>> [11552]: <-- [9:AT+FTH=3\r] Jan 22 16:14:01.98: [11552]: --> 
>>> [7:CONNECT] Jan 22 16:14:01.98: [11552]: <-- data [3] Jan 22 
>>> 16:14:01.98: [11552]: <-- data [2] Jan 22 16:14:03.16: [11552]: --> 
>>> [2:OK] Jan 22 16:14:04.16: [11552]: <-- [5:ATH0\r] Jan 22 
>>> 16:14:04.39: [11552]: --> [2:OK] Jan 22 16:14:04.39: [11552]: 
>>> SESSION END
>>> ------- Unsent job status -------
>>>      Destination: 54640
>>>            JobID: 59
>> --------------------------------------------------------------------
____________________ HylaFAX(tm) Users Mailing List
>> _______________________
>>   To subscribe/unsubscribe, click
>> http://lists.hylafax.org/cgi-bin/lsg2.cgi
>>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
>> /dev/null
>>   *To learn about commercial HylaFAX(tm) support, mail 
>> sales@xxxxxxxxx*
>
>
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
> /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail 
> sales@xxxxxxxxx*
>
>


--
Aravindan Dharmalingam
CS Linux Support Group





____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*