 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] No response to PPS repeated 3 times.:
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] No response to PPS repeated 3 times.:
- From: "CS Linux Support Group" <cslinux@xxxxxxxxxx>
- Reply-to: cslinux@xxxxxxxxxx
- Date: Wed, 23 Jan 2008 21:56:14 -0500 (EST)
Hi all,
I am using a USR V.92 5686 FAXMODEM.I installed the latest version of
hylafax server (hylafax-4.4.4).I was able to send and receive faxes
perfectly when the receiving faxmachine was a Panasonic model.
But when the I tried sending a fax to the faxmachine of model
ricoh I received the following error
"No response to PPS repeated 3 times.; Giving up after 3 attempts to send".
The faxsend requests were failing consistently when sent to a ricoh
machine and the machine is only able to receive the fax cover sheet.
I searched the mailing list for this issue and I did see postings
on it but didn't find any specific reply fixing it.
Is this issue specific to the USR modem and/or the Ricoh
faxmachine ?
Thanking you all in advance.
Aravindan.
The log I received when trying to send a fax to the ricoh faxmachine is as
follows.
--------------------------------------------------------------------
> No response to PPS repeated 3 times.; Giving up after 3 attempts to send
same page
> ---- Transcript of session follows ----
> Jan 22 16:13:32.66: [11552]: SESSION BEGIN 000000097 121254640
> Jan 22 16:13:32.66: [11552]: HylaFAX (tm) Version 4.4.2
> Jan 22 16:13:32.66: [11552]: SEND FAX: JOB 59 DEST 54640 COMMID
000000097
DEVICE '/dev/ttyS0' FROM 'acase <acase@xxxxxxxxxxxx>' USER acase
> Jan 22 16:13:32.66: [11552]: <-- [12:AT+FCLASS=1\r]
> Jan 22 16:13:32.80: [11552]: --> [2:OK]
> Jan 22 16:13:32.80: [11552]: DIAL 54640
> Jan 22 16:13:32.80: [11552]: <-- [10:ATDT54640\r]
> Jan 22 16:13:44.11: [11552]: --> [7:CONNECT]
> Jan 22 16:13:45.59: [11552]: --> [2:OK]
> Jan 22 16:13:45.59: [11552]: REMOTE NSF "00 00 25 00 00 00 92 10 4D 02
00 58
00 28 00 A0 80 80 B1 60"
> Jan 22 16:13:45.59: [11552]: NSF remote fax equipment: Ricoh
> Jan 22 16:13:45.59: [11552]: <-- [9:AT+FRH=3\r]
> Jan 22 16:13:45.60: [11552]: --> [7:CONNECT]
> Jan 22 16:13:46.02: [11552]: --> [2:OK]
> Jan 22 16:13:46.02: [11552]: REMOTE best rate 33600 bit/s
> Jan 22 16:13:46.02: [11552]: REMOTE max A3 page width (303 mm)
> Jan 22 16:13:46.02: [11552]: REMOTE max unlimited page length
> Jan 22 16:13:46.02: [11552]: REMOTE best vres 200 x 200 dpi
> Jan 22 16:13:46.02: [11552]: REMOTE format support: MH, MR, MMR, JBIG
Jan 22 16:13:46.02: [11552]: REMOTE supports T.30 Annex A, 256-byte ECM
Jan 22 16:13:46.02: [11552]: REMOTE best 10 ms/scanline
> Jan 22 16:13:46.02: [11552]: USE 14400 bit/s
> Jan 22 16:13:46.02: [11552]: USE error correction mode
> Jan 22 16:13:46.02: [11552]: SEND file "docq/cover59;f0"
> Jan 22 16:13:46.02: [11552]: USE A4 page width (215 mm)
> Jan 22 16:13:46.02: [11552]: USE unlimited page length
> Jan 22 16:13:46.02: [11552]: USE 3.85 line/mm
> Jan 22 16:13:46.02: [11552]: USE 2-D MMR
> Jan 22 16:13:46.02: [11552]: USE 0 ms/scanline
> Jan 22 16:13:46.02: [11552]: SEND training at v.17 14400 bit/s
> Jan 22 16:13:46.02: [11552]: DELAY 70 ms
> Jan 22 16:13:46.09: [11552]: <-- [9:AT+FTH=3\r]
> Jan 22 16:13:46.28: [11552]: --> [7:CONNECT]
> Jan 22 16:13:46.28: [11552]: <-- data [23]
> Jan 22 16:13:46.28: [11552]: <-- data [2]
> Jan 22 16:13:46.30: [11552]: --> [7:CONNECT]
> Jan 22 16:13:46.30: [11552]: <-- data [7]
> Jan 22 16:13:46.30: [11552]: <-- data [2]
> Jan 22 16:13:48.28: [11552]: --> [2:OK]
> Jan 22 16:13:48.28: [11552]: <-- [9:AT+FTS=7\r]
> Jan 22 16:13:48.36: [11552]: --> [2:OK]
> Jan 22 16:13:48.36: [11552]: <-- [11:AT+FTM=145\r]
> Jan 22 16:13:49.84: [11552]: --> [7:CONNECT]
> Jan 22 16:13:49.84: [11552]: <-- data [1024]
> Jan 22 16:13:49.84: [11552]: <-- data [1024]
> Jan 22 16:13:49.84: [11552]: <-- data [652]
> Jan 22 16:13:49.84: [11552]: <-- data [2]
> Jan 22 16:13:51.37: [11552]: --> [2:OK]
> Jan 22 16:13:51.37: [11552]: <-- [9:AT+FRS=1\r]
> Jan 22 16:13:51.39: [11552]: --> [2:OK]
> Jan 22 16:13:51.39: [11552]: <-- [9:AT+FRH=3\r]
> Jan 22 16:13:52.56: [11552]: --> [7:CONNECT]
> Jan 22 16:13:53.17: [11552]: --> [2:OK]
> Jan 22 16:13:53.17: [11552]: TRAINING succeeded
> Jan 22 16:13:53.17: [11552]: SEND begin page
> Jan 22 16:13:53.17: [11552]: SEND EOFB
> Jan 22 16:13:53.17: [11552]: SEND send frame number 0
> Jan 22 16:13:53.17: [11552]: SEND send frame number 1
> Jan 22 16:13:53.17: [11552]: SEND send frame number 2
> Jan 22 16:13:53.17: [11552]: SEND send frame number 3
> Jan 22 16:13:53.17: [11552]: SEND send frame number 4
> Jan 22 16:13:53.17: [11552]: SEND send frame number 5
> Jan 22 16:13:53.17: [11552]: SEND send frame number 6
> Jan 22 16:13:53.17: [11552]: SEND send frame number 7
> Jan 22 16:13:53.17: [11552]: SEND send frame number 8
> Jan 22 16:13:53.17: [11552]: SEND send frame number 9
> Jan 22 16:13:53.17: [11552]: SEND send frame number 10
> Jan 22 16:13:53.17: [11552]: SEND send frame number 11
> Jan 22 16:13:53.17: [11552]: SEND send frame number 12
> Jan 22 16:13:53.17: [11552]: SEND send frame number 13
> Jan 22 16:13:53.17: [11552]: DELAY 70 ms
> Jan 22 16:13:53.24: [11552]: <-- [11:AT+FTM=146\r]
> Jan 22 16:13:53.50: [11552]: --> [7:CONNECT]
> Jan 22 16:13:53.50: [11552]: <-- data [1034]
> Jan 22 16:13:53.50: [11552]: <-- data [1037]
> Jan 22 16:13:53.50: [11552]: <-- data [1041]
> Jan 22 16:13:53.50: [11552]: <-- data [1031]
> Jan 22 16:13:55.49: [11552]: <-- data [49]
> Jan 22 16:13:55.49: [11552]: <-- data [2]
> Jan 22 16:13:55.83: [11552]: --> [2:OK]
> Jan 22 16:13:55.83: [11552]: <-- [9:AT+FTS=7\r]
> Jan 22 16:13:55.91: [11552]: --> [2:OK]
> Jan 22 16:13:55.91: [11552]: <-- [9:AT+FTH=3\r]
> Jan 22 16:13:56.06: [11552]: --> [7:CONNECT]
> Jan 22 16:13:56.06: [11552]: <-- data [7]
> Jan 22 16:13:56.06: [11552]: <-- data [2]
> Jan 22 16:13:57.34: [11552]: --> [2:OK]
> Jan 22 16:13:57.34: [11552]: SEND send PPS (partial page signal) Jan 22
16:13:57.34: [11552]: SEND send MPS (more pages, same document) Jan 22
16:13:57.34: [11552]: <-- [9:AT+FRH=3\r]
> Jan 22 16:13:57.71: [11552]: --> [10:NO CARRIER]
> Jan 22 16:13:57.71: [11552]: MODEM No carrier
> Jan 22 16:13:57.71: [11552]: <-- [9:AT+FTH=3\r]
> Jan 22 16:13:57.91: [11552]: --> [7:CONNECT]
> Jan 22 16:13:57.91: [11552]: <-- data [7]
> Jan 22 16:13:57.91: [11552]: <-- data [2]
> Jan 22 16:13:59.19: [11552]: --> [2:OK]
> Jan 22 16:13:59.19: [11552]: SEND send PPS (partial page signal) Jan 22
16:13:59.19: [11552]: SEND send MPS (more pages, same document) Jan 22
16:13:59.19: [11552]: <-- [9:AT+FRH=3\r]
> Jan 22 16:13:59.76: [11552]: --> [10:NO CARRIER]
> Jan 22 16:13:59.76: [11552]: MODEM No carrier
> Jan 22 16:13:59.76: [11552]: <-- [9:AT+FTH=3\r]
> Jan 22 16:13:59.95: [11552]: --> [7:CONNECT]
> Jan 22 16:13:59.95: [11552]: <-- data [7]
> Jan 22 16:13:59.95: [11552]: <-- data [2]
> Jan 22 16:14:01.24: [11552]: --> [2:OK]
> Jan 22 16:14:01.24: [11552]: SEND send PPS (partial page signal) Jan 22
16:14:01.24: [11552]: SEND send MPS (more pages, same document) Jan 22
16:14:01.24: [11552]: <-- [9:AT+FRH=3\r]
> Jan 22 16:14:01.71: [11552]: --> [10:NO CARRIER]
> Jan 22 16:14:01.71: [11552]: MODEM No carrier
> Jan 22 16:14:01.71: [11552]: No response to PPS repeated 3 times. Jan 22
16:14:01.71: [11552]: SEND end page
> Jan 22 16:14:01.71: [11552]: SEND: Giving up after 3 attempts to send
same
page "docq/cover59;f0", dirnum 0
> Jan 22 16:14:01.71: [11552]: DELAY 70 ms
> Jan 22 16:14:01.79: [11552]: <-- [9:AT+FTH=3\r]
> Jan 22 16:14:01.98: [11552]: --> [7:CONNECT]
> Jan 22 16:14:01.98: [11552]: <-- data [3]
> Jan 22 16:14:01.98: [11552]: <-- data [2]
> Jan 22 16:14:03.16: [11552]: --> [2:OK]
> Jan 22 16:14:04.16: [11552]: <-- [5:ATH0\r]
> Jan 22 16:14:04.39: [11552]: --> [2:OK]
> Jan 22 16:14:04.39: [11552]: SESSION END
> ------- Unsent job status -------
> Destination: 54640
> JobID: 59
--------------------------------------------------------------------
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] No response to PPS repeated 3 times.:
- From: Daren Russell
- Re: [hylafax-users] No response to PPS repeated 3 times.:
- From: Lee Howard
- Re: [hylafax-users] No response to PPS repeated 3 times.:
- Prev by Date: Re: [hylafax-users] Hardware suggestions to get Hylafax running?
- Next by Date: [hylafax-users] turning off dial tone detect
- Previous by thread: Re: [hylafax-users] Incomming Job No. limited to 1000 ? - solved
- Next by thread: Re: [hylafax-users] No response to PPS repeated 3 times.:
- Index(es):
Project hosted by iFAX Solutions