Re: [hylafax-users] EICON users

["Luke McKee" <hojuruku@xxxxxxxxx>]

I made an earlier suggestion to use CAPI for receiving faxes. There was a patch to asterisk to allow DID fax receiving to a file.
Once the file is imported you could create a custom faxrecvd process to inject it back into hylafax and continue to send as per normal.
Note this only applies to using CAPI with EICON Diva fax servers.

This could work around some of the "problem" people have been having. I found that little patch / gem hiding in the asteriskbrazil forum and thought I'd share it.

If you have trouble digging up the post let me know (should be in web archive - whole new thread about EICON thing late last month)

Cheers,

Luke

On 09/05/07, Mark Hunting <mark@xxxxxxxxxx> wrote:

I use the same cards as you (versions 1, 2 and 3), also with the
diva_tty driver. I also had to struggle a lot with the modem config, but
now it works very well. I don't use the drivers 'Super Fine/Ultra Fine
resolutions' setting however, do you want to use that? I just use the
Hylafax 'normal' resolution. This is my modem config:


CountryCode:            31
AreaCode:               20
FAXNumber:              ""
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
JobRetryNoCarrier:      0
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        ""
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          ""

MaxConsecutiveBadLines: 0               # don't check (default is 5)
PercentGoodLines:       0               # don't check (default is 95%)

ModemType:              Class2          # use this to supply a hint
ModemRate:              57600           # on boards supporting V.34-fax,
                                        # this may need to be 57600
ModemFlowControl:       rtscts
ModemNoFlowCmd:         AT&K0
ModemSoftFlowCmd:       AT&K4
ModemHardFlowCmd:       AT&K3

ModemResetCmds:         "AT#CID=15+iQ=a1" # port 01-30: a1, 31-60: a2, etc.

Class2APQueryCmd:       none
Class2SPLCmd:           none
Class2ECMType:          2.0             # see README or
http://www.hylafax.org/archive/2004-06/msg00080.php
Class2CQQueryCmd:       !3
Class2CQCmd:            AT

Class2TBCCmd:           none
Class2PHCTOCmd:         none

QualifyCID:            "etc/cid"
CIDNumber:             "RING;"
RingExtended:          "RING;"

Regards,
Mark




Moritz Winterberg wrote:
> Those of you who are using Eicon Diva Server Cards with hylafax:
>
> I'd like to have a little exchange about modem config and card driver
> (config and version).
> And maybe also some typical problems.
>
> I'm using DIVA PRI E1 30 cards with eicons diva_tty  driver. I have
> been using capi before
> but wanted to take out capi4hylafax. This is another story though.
> I use driver version 107-13 (compiled from source) on Debian.
>
> I'm generally happy with the cards performance I just have problems
> sending fine resolution at the moment. I'm working on it with Eicon
> Support.
>
> Here is my modem config. I would be happy if you'd like to share yours
> and tell me your experiences:
>
> -----------------------------------------------------
> LongDistancePrefix:     0
> InternationalPrefix:    00
> DialStringRules:        etc/dialrules
> ServerTracing:          0xFFFFF
> SessionTracing:         0xFFFFF
> RecvFileMode:           0600
> LogFileMode:            0600
> DeviceMode:                     0600
> RingsBeforeAnswer:      3
> SpeakerVolume:          off
> GettyArgs:         "-b -r -s %s %l"
> LocalIdentifier:         blablub
> TagLineFont:            etc/lutRS18.pcf
> TagLineFormat:      "%%m|%t|Seite %%P von %%T"
> MaxRecvPages:           200
> MaxConsecutiveBadLines: 0       # don't check, it will produce to many
> failures
> PercentGoodLines:   0       # don't check
> #
> #
> ModemType:              Class2   # I've never been sure about what
> class to use best ??
> ModemRate:              57600   # Diva Server supports V.34-fax
> ModemFlowControl:       rtscts
> ModemNoFlowCmd:         AT&K0
> ModemSoftFlowCmd:       AT&K4
> ModemHardFlowCmd:       AT&K3
> #
> #
> # Enable this to set Caller*ID Number
> #
> ModemSetOriginCmd:     AT+iO%d
>
> ModemResultCodesCmd:    ATQ0            # enable result codes
> ModemVerboseResultsCmd: ATV1            # enable verbose command results
>
> Class2APQueryCmd:       none
> Class2SPLCmd:           none
> Class2TBCCmd:           none
> Class2ECMType:          2     # follows Class 2.0 spec, not Class 2
> Class2UseHex:           true
>
> #Bind Modem to Controller 1
> ModemResetCmds:         AT#CID=14+iQ=a1
>
> # I'd like to retrieve Caller information
> CIDNumber:              "DAD: "
> CIDName:                "CID: "
> --------------------------------------------
>
> Moritz
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
>  To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxx .*
>

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*