Re: [hylafax-users] EICON users

[Mark Hunting <mark@xxxxxxxxxx>]

I use the same cards as you (versions 1, 2 and 3), also with the 
diva_tty driver. I also had to struggle a lot with the modem config, but 
now it works very well. I don't use the drivers 'Super Fine/Ultra Fine 
resolutions' setting however, do you want to use that? I just use the 
Hylafax 'normal' resolution. This is my modem config:


CountryCode:            31
AreaCode:               20
FAXNumber:              ""
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
JobRetryNoCarrier:      0
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        ""
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          ""

MaxConsecutiveBadLines: 0               # don't check (default is 5)
PercentGoodLines:       0               # don't check (default is 95%)

ModemType:              Class2          # use this to supply a hint
ModemRate:              57600           # on boards supporting V.34-fax,
                                       # this may need to be 57600
ModemFlowControl:       rtscts
ModemNoFlowCmd:         AT&K0
ModemSoftFlowCmd:       AT&K4
ModemHardFlowCmd:       AT&K3

ModemResetCmds:         "AT#CID=15+iQ=a1" # port 01-30: a1, 31-60: a2, etc.

Class2APQueryCmd:       none
Class2SPLCmd:           none
Class2ECMType:          2.0             # see README or 
http://www.hylafax.org/archive/2004-06/msg00080.php
Class2CQQueryCmd:       !3
Class2CQCmd:            AT

Class2TBCCmd:           none
Class2PHCTOCmd:         none

QualifyCID:            "etc/cid"
CIDNumber:             "RING;"
RingExtended:          "RING;"

Regards,
Mark




Moritz Winterberg wrote:
> Those of you who are using Eicon Diva Server Cards with hylafax:
>
> I'd like to have a little exchange about modem config and card driver
> (config and version).
> And maybe also some typical problems.
>
> I'm using DIVA PRI E1 30 cards with eicons diva_tty  driver. I have
> been using capi before
> but wanted to take out capi4hylafax. This is another story though.
> I use driver version 107-13 (compiled from source) on Debian.
>
> I'm generally happy with the cards performance I just have problems
> sending fine resolution at the moment. I'm working on it with Eicon
> Support.
>
> Here is my modem config. I would be happy if you'd like to share yours
> and tell me your experiences:
>
> -----------------------------------------------------
> LongDistancePrefix:     0
> InternationalPrefix:    00
> DialStringRules:        etc/dialrules
> ServerTracing:          0xFFFFF
> SessionTracing:         0xFFFFF
> RecvFileMode:           0600
> LogFileMode:            0600
> DeviceMode:                     0600
> RingsBeforeAnswer:      3
> SpeakerVolume:          off
> GettyArgs:         "-b -r -s %s %l"
> LocalIdentifier:         blablub
> TagLineFont:            etc/lutRS18.pcf
> TagLineFormat:      "%%m|%t|Seite %%P von %%T"
> MaxRecvPages:           200
> MaxConsecutiveBadLines: 0       # don't check, it will produce to many 
> failures
> PercentGoodLines:   0       # don't check
> #
> #
> ModemType:              Class2   # I've never been sure about what
> class to use best ??
> ModemRate:              57600   # Diva Server supports V.34-fax
> ModemFlowControl:       rtscts
> ModemNoFlowCmd:         AT&K0
> ModemSoftFlowCmd:       AT&K4
> ModemHardFlowCmd:       AT&K3
> #
> #
> # Enable this to set Caller*ID Number
> #
> ModemSetOriginCmd:     AT+iO%d
>
> ModemResultCodesCmd:    ATQ0            # enable result codes
> ModemVerboseResultsCmd: ATV1            # enable verbose command results
>
> Class2APQueryCmd:       none
> Class2SPLCmd:           none
> Class2TBCCmd:           none
> Class2ECMType:          2     # follows Class 2.0 spec, not Class 2
> Class2UseHex:           true
>
> #Bind Modem to Controller 1
> ModemResetCmds:         AT#CID=14+iQ=a1
>
> # I'd like to retrieve Caller information
> CIDNumber:              "DAD: "
> CIDName:                "CID: "
> --------------------------------------------
>
> Moritz
>
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>  To subscribe/unsubscribe, click 
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
> /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*