Re: [hylafax-users] No response to MPS repeated 3 tries; too many attempts to dial

["Andrew Rinaldi" <andrew.rinaldi@xxxxxxxxxxxx>]

Hi Paolo,

 

This is a IP568x chipset from IC ACE Corp (www.icace.com.tw).  I would guess from the dates of the firmware (2002) that they were related to IC Plus Corp (www.icplus.com.tw) at the time they left the modem market.

 

If you search www.hylafax.org for ip586x (note 586 NOT 568) you will find users reporting issues with this chipset.  Most of these chipsets have no external flash and therefore cannot be upgraded (even if they could no new firmware is available as far as I’m aware).

 

Time to get yourself a new modem based on the Agere Venus chipset...

 

Regards

 

ANDREW RINALDI

Mainpine Limited - Support

USA +1 503 822 9944 | Asia/Europe +44 1225 869439  

andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com

 

From: T.C.P. Sistemi [mailto:info@xxxxxxxxxxxxx]
Sent: 24 April 2007 10:56
To: andrew.rinaldi@xxxxxxxxxxxx
Cc: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] No response to MPS repeated 3 tries; too many attempts to dial

 

Hi,
Here is the result of AT commands:

ATI0
TP560 Data/Fax/Voice 56K Modem
OK
ATI1
External Controller Ver3.00, CheckSum=3802
OK
ATI2
TEST OK!
OK
ATI3
TP560 Data/Fax/Voice 56K Modem
OK
ATI4
DSP Ver3.00 CheckSum=668C
OK
ATI5
CTR21 Complex Impedence
OK
ATI6
0
OK
ATI7
Controller Ver3.00 Date:Jan 02 14:16 2002
OK
ATI8
DSP Ver3.00 Date:Jan 02 14:06 2002
OK
ATI9
Software Speakerphone
OK
ATI10
Program Memory CheckSum=9E8E
OK
ATI11

 

C56
OK

Thank You for your help,

Paolo Ciucani

Andrew Rinaldi ha scritto:

Hi,

Are you sure this modem is using the IC Plus chipset ?  Is this the INF file

that you actually used to install the modem under Windows ?  Can you use

Minicom to issue information commands (ATI0, ATI1, etc) until you reach

ATI11 and then send us the results ?  This will confirm the modem type and

firmware revision.

The reason I'm asking you to verify the modem type is because IC Plus left

the modem market several years ago and therefore I'm surprised that you can

still buy a modem with this chipset.

Regards

ANDREW RINALDI

Mainpine Limited - Support

USA +1 503 822 9944 | Asia/Europe +44 1225 869439  

andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com

-----Original Message-----

From: T.C.P. Sistemi [mailto:info@xxxxxxxxxxxxx] 

Sent: 19 April 2007 09:44

To: andrew.rinaldi@xxxxxxxxxxxx; hylafax-users@xxxxxxxxxxx

Subject: Re: [hylafax-users] No response to MPS repeated 3 tries; too many

attempts to dial

I have an external RS232 modem, model "Mediacom 103/ME56W" 

(http://www.mediacomeurope.it/prodotto.asp?pid=10) which use an IC Plus 

Semiconductor Chipset (I have seen it in the windows .inf file 

http://contents.driverguide.com/content.php?id=57025&path=WinXP%2Ficp.inf )

Thank You

Andrew Rinaldi ha scritto:

Hi,

What modem are you using ?

Regards

*ANDREW RINALDI*

*Mainpine Limited - Support*

USA +1 503 822 9944 | Asia/Europe +44 1225 869439  

andrew.rinaldi@xxxxxxxxxxxx <mailto:andrew.rinaldi@xxxxxxxxxxxx> | 

www.mainpine.com <http://www.mainpine.com/>

*From:* hylafax-users-bounce@xxxxxxxxxxx 

[mailto:hylafax-users-bounce@xxxxxxxxxxx] *On Behalf Of *T.C.P. Sistemi

*Sent:* 18 April 2007 18:45

*To:* hylafax-users@xxxxxxxxxxx

*Subject:* [hylafax-users] No response to MPS repeated 3 tries; too 

many attempts to dial

Hallo All,

I have a problem when I try to send a long fax with Hylafax Version 

4.3.3 on Linux Fedora 5;

here is log of the session:

---------------------------------------------------

Your job to XXXXXXXXX failed because:

No response to MPS repeated 3 tries; too many attempts to dial

    ---- Transcript of session follows ----

apr 18 18:01:00.08: [11872]: SESSION BEGIN 000000440 39861067822820

apr 18 18:01:00.08: [11872]: HylaFAX (tm) Version 4.3.3

apr 18 18:01:00.08: [11872]: SEND FAX: JOB 25 DEST XXXXXXXX COMMID

000000440 DEVICE '/dev/ttyS0' FROM 'faxuser 

<xxxxxxxxxx@xxxxxxxxxxxxx>' <mailto:giorgio@xxxxxxxxxxxxxxxxxxxxx%3E%27>

USER faxuser

apr 18 18:01:00.08: [11872]: <-- [12:AT+FCLASS=1\r]

apr 18 18:01:00.19: [11872]: --> [2:OK]

apr 18 18:01:00.19: [11872]: DIAL XXXXXXXX

apr 18 18:01:00.19: [11872]: <-- [14:ATDTXXXXXXXX\r]

apr 18 18:01:40.62: [11872]: --> [7:CONNECT]

apr 18 18:01:42.16: [11872]: --> [2:OK]

apr 18 18:01:42.16: [11872]: REMOTE NSF "50 80 00 A6 00 00 02 00 00 00 

00 00

00 00 00 00 00 00 00 FF"

apr 18 18:01:42.16: [11872]: NSF remote fax equipment: unknown

apr 18 18:01:42.16: [11872]: <-- [9:AT+FRH=3\r]

apr 18 18:01:42.18: [11872]: --> [7:CONNECT]

apr 18 18:01:42.86: [11872]: --> [2:OK]

apr 18 18:01:42.86: [11872]: REMOTE CSI "XXXXXXXX"

apr 18 18:01:42.86: [11872]: <-- [9:AT+FRH=3\r]

apr 18 18:01:42.88: [11872]: --> [7:CONNECT]

apr 18 18:01:43.22: [11872]: --> [2:OK]

apr 18 18:01:43.22: [11872]: REMOTE best rate 9600 bit/s

apr 18 18:01:43.22: [11872]: REMOTE max A4 page width (215 mm)

apr 18 18:01:43.22: [11872]: REMOTE max unlimited page length

apr 18 18:01:43.22: [11872]: REMOTE best vres 7.7 line/mm

apr 18 18:01:43.22: [11872]: REMOTE format support: MH, MR

apr 18 18:01:43.22: [11872]: REMOTE best 20 ms, 10 ms/scanline

apr 18 18:01:43.22: [11872]: USE 9600 bit/s

apr 18 18:01:43.22: [11872]: SEND file "docq/doc25.ps;c1"

apr 18 18:01:43.22: [11872]: USE A4 page width (215 mm)

apr 18 18:01:43.22: [11872]: USE unlimited page length

apr 18 18:01:43.22: [11872]: USE 7.7 line/mm

apr 18 18:01:43.22: [11872]: USE 2-D MR

apr 18 18:01:43.22: [11872]: USE 10 ms/scanline

apr 18 18:01:43.22: [11872]: SEND training at v.29 9600 bit/s

apr 18 18:01:43.22: [11872]: DELAY 70 ms

apr 18 18:01:43.29: [11872]: <-- [9:AT+FTH=3\r]

apr 18 18:01:43.34: [11872]: --> [7:CONNECT]

apr 18 18:01:43.37: [11872]: --> [7:CONNECT]

apr 18 18:01:45.53: [11872]: --> [2:OK]

apr 18 18:01:45.53: [11872]: DELAY 70 ms

apr 18 18:01:45.61: [11872]: <-- [10:AT+FTM=96\r]

apr 18 18:01:46.12: [11872]: --> [7:CONNECT]

apr 18 18:01:47.67: [11872]: --> [2:OK]

apr 18 18:01:47.67: [11872]: <-- [9:AT+FRH=3\r]

apr 18 18:01:48.17: [11872]: --> [7:CONNECT]

apr 18 18:01:49.34: [11872]: --> [2:OK]

apr 18 18:01:49.34: [11872]: TRAINING succeeded

apr 18 18:01:49.34: [11872]: DELAY 70 ms

apr 18 18:01:49.41: [11872]: <-- [10:AT+FTM=96\r]

apr 18 18:01:50.00: [11872]: --> [7:CONNECT]

apr 18 18:01:50.00: [11872]: SEND begin page

apr 18 18:01:50.04: [11872]: Reading MMR-compressed image file

apr 18 18:01:50.07: [11872]: SENT 74 bytes of data

apr 18 18:01:50.07: [11872]: SENT 71 bytes of data

.......................................

.......................................

apr 18 18:02:12.13: [11872]: SENT 72 bytes of data

apr 18 18:02:12.13: [11872]: SENT 72 bytes of data

apr 18 18:02:12.13: [11872]: SENT 60 bytes of data

apr 18 18:02:12.13: [11872]: SEND 2D RTC

apr 18 18:02:12.13: [11872]: SEND end page

apr 18 18:02:27.01: [11872]: --> [2:OK]

apr 18 18:02:27.01: [11872]: DELAY 70 ms

apr 18 18:02:27.08: [11872]: SEND send MPS (more pages, same document)

apr 18 18:02:27.08: [11872]: <-- [9:AT+FTH=3\r]

apr 18 18:02:27.13: [11872]: --> [7:CONNECT]

apr 18 18:02:28.44: [11872]: --> [2:OK]

apr 18 18:02:28.44: [11872]: <-- [9:AT+FRH=3\r]

apr 18 18:02:31.55: [11872]: --> [0:]

apr 18 18:02:31.55: [11872]: MODEM <Empty line>

apr 18 18:02:31.75: [11872]: MODEM <Timeout>

apr 18 18:02:31.75: [11872]: SEND send MPS (more pages, same document)

apr 18 18:02:31.75: [11872]: <-- [9:AT+FTH=3\r]

apr 18 18:02:31.80: [11872]: --> [7:CONNECT]

apr 18 18:02:33.12: [11872]: --> [2:OK]

apr 18 18:02:33.12: [11872]: <-- [9:AT+FRH=3\r]

apr 18 18:02:36.22: [11872]: --> [0:]

apr 18 18:02:36.22: [11872]: MODEM <Empty line>

apr 18 18:02:36.43: [11872]: MODEM <Timeout>

apr 18 18:02:36.43: [11872]: SEND send MPS (more pages, same document)

apr 18 18:02:36.43: [11872]: <-- [9:AT+FTH=3\r]

apr 18 18:02:36.47: [11872]: --> [7:CONNECT]

apr 18 18:02:37.79: [11872]: --> [2:OK]

apr 18 18:02:37.79: [11872]: <-- [9:AT+FRH=3\r]

apr 18 18:02:40.89: [11872]: --> [0:]

apr 18 18:02:40.89: [11872]: MODEM <Empty line>

apr 18 18:02:41.10: [11872]: MODEM <Timeout>

apr 18 18:02:41.10: [11872]: No response to MPS repeated 3 tries

apr 18 18:02:41.10: [11872]: <-- [9:AT+FTH=3\r]

apr 18 18:02:41.15: [11872]: --> [7:CONNECT]

apr 18 18:02:42.46: [11872]: --> [2:OK]

apr 18 18:02:42.46: [11872]: SEND FAILED: JOB 25 DEST XXXXXXXX ERR No

response to MPS repeated 3 tries; too many attempts to dial

apr 18 18:02:42.46: [11872]: <-- [5:ATH0\r]

apr 18 18:02:42.89: [11872]: --> [10:NO CARRIER]

apr 18 18:02:42.89: [11872]: MODEM No carrier

apr 18 18:02:42.89: [11872]: SESSION END

------- Unsent job status -------

      Destination: XXXXXXXX

            JobID: 25

          GroupID: 25

           Sender: faxuser

         Mailaddr: xxxxx@xxxxxxxxxxx <mailto:xxxxx@xxxxxxxxxxx>

           CommID: 000000440

            Modem: any

   Submitted From: 192.168.0.11

       Page Width: 194  (mm)

      Page Length: 281 (mm)

       Resolution: 213 (lpi)

           Status: No response to MPS repeated 3 tries; too many 

attempts to

dial

          Dialogs: 2

            Dials: 0

            Calls: 2

            Pages: 0

         TotPages: 7

         Attempts: 2

           Dirnum:

---------------------------------------------------

can anyone help me, please??

Thank You

Bye

 

--
Nota di riservatezza: il presente messaggio, corredato dei relativi allegati, contiene informazioni da considerarsi strettamente riservate ed è destinato esclusivamente al destinatario sopra indicato, il quale è l'unico autorizzato ad usarlo, copiarlo e, sotto la propria responsabilità, diffonderlo. Chiunque ricevesse questo messaggio per errore o comunque lo leggesse senza esserne legittimato è avvertito che trattenerlo, copiarlo, divulgarlo, distribuirlo a persone diverse dal destinatario è severamente proibito ed è pregato di rinviarlo immediatamente al mittente distruggendo l'originale. Grazie.

Confidentiality notice: this message, together with its annexes, contains information to be deemed strictly confidential and is destined only to the addressee(s) identified above who only may use, copy and, under his/their responsibility, further disseminate it. If anyone received this message by mistake or reads it without entitlement is forewarned that keeping, copying, disseminating or distributing this message to persons other than the addressee(s) is strictly forbidden and is asked to transmit it immediately to the sender and to erase the original message received. Thank you.