Hi,
What modem are you using ?
Regards
From:
hylafax-users-bounce@xxxxxxxxxxx [mailto:hylafax-users-bounce@xxxxxxxxxxx] On
Behalf Of T.C.P. Sistemi
Sent: 18 April 2007 18:45
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] No response to MPS repeated 3 tries; too many
attempts to dial
Hallo All,
I have a problem when I try to send a long fax with Hylafax Version 4.3.3 on
Linux Fedora 5;
here is log of the session:
---------------------------------------------------
Your job to XXXXXXXXX failed because:
No response to MPS repeated 3 tries; too many attempts to dial
---- Transcript of session follows ----
apr 18 18:01:00.08: [11872]: SESSION BEGIN 000000440 39861067822820
apr 18 18:01:00.08: [11872]: HylaFAX (tm) Version 4.3.3
apr 18 18:01:00.08: [11872]: SEND FAX: JOB 25 DEST XXXXXXXX COMMID
000000440 DEVICE '/dev/ttyS0' FROM 'faxuser <xxxxxxxxxx@xxxxxxxxxxxxx>'
USER faxuser
apr 18 18:01:00.08: [11872]: <-- [12:AT+FCLASS=1\r]
apr 18 18:01:00.19: [11872]: --> [2:OK]
apr 18 18:01:00.19: [11872]: DIAL XXXXXXXX
apr 18 18:01:00.19: [11872]: <-- [14:ATDTXXXXXXXX\r]
apr 18 18:01:40.62: [11872]: --> [7:CONNECT]
apr 18 18:01:42.16: [11872]: --> [2:OK]
apr 18 18:01:42.16: [11872]: REMOTE NSF "50 80 00 A6 00 00 02 00 00 00 00
00
00 00 00 00 00 00 00 FF"
apr 18 18:01:42.16: [11872]: NSF remote fax equipment: unknown
apr 18 18:01:42.16: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:01:42.18: [11872]: --> [7:CONNECT]
apr 18 18:01:42.86: [11872]: --> [2:OK]
apr 18 18:01:42.86: [11872]: REMOTE CSI "XXXXXXXX"
apr 18 18:01:42.86: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:01:42.88: [11872]: --> [7:CONNECT]
apr 18 18:01:43.22: [11872]: --> [2:OK]
apr 18 18:01:43.22: [11872]: REMOTE best rate 9600 bit/s
apr 18 18:01:43.22: [11872]: REMOTE max A4 page width (215 mm)
apr 18 18:01:43.22: [11872]: REMOTE max unlimited page length
apr 18 18:01:43.22: [11872]: REMOTE best vres 7.7 line/mm
apr 18 18:01:43.22: [11872]: REMOTE format support: MH, MR
apr 18 18:01:43.22: [11872]: REMOTE best 20 ms, 10 ms/scanline
apr 18 18:01:43.22: [11872]: USE 9600 bit/s
apr 18 18:01:43.22: [11872]: SEND file "docq/doc25.ps;c1"
apr 18 18:01:43.22: [11872]: USE A4 page width (215 mm)
apr 18 18:01:43.22: [11872]: USE unlimited page length
apr 18 18:01:43.22: [11872]: USE 7.7 line/mm
apr 18 18:01:43.22: [11872]: USE 2-D MR
apr 18 18:01:43.22: [11872]: USE 10 ms/scanline
apr 18 18:01:43.22: [11872]: SEND training at v.29 9600 bit/s
apr 18 18:01:43.22: [11872]: DELAY 70 ms
apr 18 18:01:43.29: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:01:43.34: [11872]: --> [7:CONNECT]
apr 18 18:01:43.37: [11872]: --> [7:CONNECT]
apr 18 18:01:45.53: [11872]: --> [2:OK]
apr 18 18:01:45.53: [11872]: DELAY 70 ms
apr 18 18:01:45.61: [11872]: <-- [10:AT+FTM=96\r]
apr 18 18:01:46.12: [11872]: --> [7:CONNECT]
apr 18 18:01:47.67: [11872]: --> [2:OK]
apr 18 18:01:47.67: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:01:48.17: [11872]: --> [7:CONNECT]
apr 18 18:01:49.34: [11872]: --> [2:OK]
apr 18 18:01:49.34: [11872]: TRAINING succeeded
apr 18 18:01:49.34: [11872]: DELAY 70 ms
apr 18 18:01:49.41: [11872]: <-- [10:AT+FTM=96\r]
apr 18 18:01:50.00: [11872]: --> [7:CONNECT]
apr 18 18:01:50.00: [11872]: SEND begin page
apr 18 18:01:50.04: [11872]: Reading MMR-compressed image file
apr 18 18:01:50.07: [11872]: SENT 74 bytes of data
apr 18 18:01:50.07: [11872]: SENT 71 bytes of data
.......................................
.......................................
apr 18 18:02:12.13: [11872]: SENT 72 bytes of data
apr 18 18:02:12.13: [11872]: SENT 72 bytes of data
apr 18 18:02:12.13: [11872]: SENT 60 bytes of data
apr 18 18:02:12.13: [11872]: SEND 2D RTC
apr 18 18:02:12.13: [11872]: SEND end page
apr 18 18:02:27.01: [11872]: --> [2:OK]
apr 18 18:02:27.01: [11872]: DELAY 70 ms
apr 18 18:02:27.08: [11872]: SEND send MPS (more pages, same document)
apr 18 18:02:27.08: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:27.13: [11872]: --> [7:CONNECT]
apr 18 18:02:28.44: [11872]: --> [2:OK]
apr 18 18:02:28.44: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:02:31.55: [11872]: --> [0:]
apr 18 18:02:31.55: [11872]: MODEM <Empty line>
apr 18 18:02:31.75: [11872]: MODEM <Timeout>
apr 18 18:02:31.75: [11872]: SEND send MPS (more pages, same document)
apr 18 18:02:31.75: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:31.80: [11872]: --> [7:CONNECT]
apr 18 18:02:33.12: [11872]: --> [2:OK]
apr 18 18:02:33.12: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:02:36.22: [11872]: --> [0:]
apr 18 18:02:36.22: [11872]: MODEM <Empty line>
apr 18 18:02:36.43: [11872]: MODEM <Timeout>
apr 18 18:02:36.43: [11872]: SEND send MPS (more pages, same document)
apr 18 18:02:36.43: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:36.47: [11872]: --> [7:CONNECT]
apr 18 18:02:37.79: [11872]: --> [2:OK]
apr 18 18:02:37.79: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:02:40.89: [11872]: --> [0:]
apr 18 18:02:40.89: [11872]: MODEM <Empty line>
apr 18 18:02:41.10: [11872]: MODEM <Timeout>
apr 18 18:02:41.10: [11872]: No response to MPS repeated 3 tries
apr 18 18:02:41.10: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:41.15: [11872]: --> [7:CONNECT]
apr 18 18:02:42.46: [11872]: --> [2:OK]
apr 18 18:02:42.46: [11872]: SEND FAILED: JOB 25 DEST XXXXXXXX ERR No
response to MPS repeated 3 tries; too many attempts to dial
apr 18 18:02:42.46: [11872]: <-- [5:ATH0\r]
apr 18 18:02:42.89: [11872]: --> [10:NO CARRIER]
apr 18 18:02:42.89: [11872]: MODEM No carrier
apr 18 18:02:42.89: [11872]: SESSION END
------- Unsent job status -------
Destination: XXXXXXXX
JobID: 25
GroupID: 25
Sender: faxuser
Mailaddr: xxxxx@xxxxxxxxxxx
CommID: 000000440
Modem: any
Submitted From: 192.168.0.11
Page Width: 194 (mm)
Page Length: 281 (mm)
Resolution: 213 (lpi)
Status: No
response to MPS repeated 3 tries; too many attempts to
dial
Dialogs: 2
Dials: 0
Calls: 2
Pages: 0
TotPages: 7
Attempts: 2
Dirnum:
---------------------------------------------------
can anyone help me, please??
Thank You
Bye