Re: [hylafax-users] No response to MPS repeated 3 tries; too many attempts to dial

["T.C.P. Sistemi" <info@xxxxxxxxxxxxx>]

Hi,
Here is the result of AT commands:

ATI0
TP560 Data/Fax/Voice 56K Modem
OK
ATI1
External Controller Ver3.00, CheckSum=3802
OK
ATI2
TEST OK!
OK
ATI3
TP560 Data/Fax/Voice 56K Modem
OK
ATI4
DSP Ver3.00 CheckSum=668C
OK
ATI5
CTR21 Complex Impedence
OK
ATI6
0
OK
ATI7
Controller Ver3.00 Date:Jan 02 14:16 2002
OK
ATI8
DSP Ver3.00 Date:Jan 02 14:06 2002
OK
ATI9
Software Speakerphone
OK
ATI10
Program Memory CheckSum=9E8E
OK
ATI11

 

C56
OK

Thank You for your help,
Paolo Ciucani

Andrew Rinaldi ha scritto:

Hi,

Are you sure this modem is using the IC Plus chipset ?  Is this the INF file
that you actually used to install the modem under Windows ?  Can you use
Minicom to issue information commands (ATI0, ATI1, etc) until you reach
ATI11 and then send us the results ?  This will confirm the modem type and
firmware revision.

The reason I'm asking you to verify the modem type is because IC Plus left
the modem market several years ago and therefore I'm surprised that you can
still buy a modem with this chipset.

Regards

ANDREW RINALDI
Mainpine Limited - Support
USA +1 503 822 9944 | Asia/Europe +44 1225 869439  
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com

-----Original Message-----
From: T.C.P. Sistemi [mailto:info@xxxxxxxxxxxxx] 
Sent: 19 April 2007 09:44
To: andrew.rinaldi@xxxxxxxxxxxx; hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] No response to MPS repeated 3 tries; too many
attempts to dial

I have an external RS232 modem, model "Mediacom 103/ME56W" 
(http://www.mediacomeurope.it/prodotto.asp?pid=10) which use an IC Plus 
Semiconductor Chipset (I have seen it in the windows .inf file 
http://contents.driverguide.com/content.php?id=57025&path=WinXP%2Ficp.inf )

Thank You

Andrew Rinaldi ha scritto:
  

Hi,

 

What modem are you using ?

 

Regards

 

*ANDREW RINALDI*

*Mainpine Limited - Support*

USA +1 503 822 9944 | Asia/Europe +44 1225 869439  

andrew.rinaldi@xxxxxxxxxxxx <mailto:andrew.rinaldi@xxxxxxxxxxxx> | 
www.mainpine.com <http://www.mainpine.com/>

 

*From:* hylafax-users-bounce@xxxxxxxxxxx 
[mailto:hylafax-users-bounce@xxxxxxxxxxx] *On Behalf Of *T.C.P. Sistemi
*Sent:* 18 April 2007 18:45
*To:* hylafax-users@xxxxxxxxxxx
*Subject:* [hylafax-users] No response to MPS repeated 3 tries; too 
many attempts to dial

 

Hallo All,

I have a problem when I try to send a long fax with Hylafax Version 
4.3.3 on Linux Fedora 5;
here is log of the session:

---------------------------------------------------
Your job to XXXXXXXXX failed because:

No response to MPS repeated 3 tries; too many attempts to dial


    ---- Transcript of session follows ----

apr 18 18:01:00.08: [11872]: SESSION BEGIN 000000440 39861067822820
apr 18 18:01:00.08: [11872]: HylaFAX (tm) Version 4.3.3
apr 18 18:01:00.08: [11872]: SEND FAX: JOB 25 DEST XXXXXXXX COMMID
000000440 DEVICE '/dev/ttyS0' FROM 'faxuser 
<xxxxxxxxxx@xxxxxxxxxxxxx>' <mailto:giorgio@xxxxxxxxxxxxxxxxxxxxx%3E%27>
USER faxuser
apr 18 18:01:00.08: [11872]: <-- [12:AT+FCLASS=1\r]
apr 18 18:01:00.19: [11872]: --> [2:OK]
apr 18 18:01:00.19: [11872]: DIAL XXXXXXXX
apr 18 18:01:00.19: [11872]: <-- [14:ATDTXXXXXXXX\r]
apr 18 18:01:40.62: [11872]: --> [7:CONNECT]
apr 18 18:01:42.16: [11872]: --> [2:OK]
apr 18 18:01:42.16: [11872]: REMOTE NSF "50 80 00 A6 00 00 02 00 00 00 
00 00
00 00 00 00 00 00 00 FF"
apr 18 18:01:42.16: [11872]: NSF remote fax equipment: unknown
apr 18 18:01:42.16: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:01:42.18: [11872]: --> [7:CONNECT]
apr 18 18:01:42.86: [11872]: --> [2:OK]
apr 18 18:01:42.86: [11872]: REMOTE CSI "XXXXXXXX"
apr 18 18:01:42.86: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:01:42.88: [11872]: --> [7:CONNECT]
apr 18 18:01:43.22: [11872]: --> [2:OK]
apr 18 18:01:43.22: [11872]: REMOTE best rate 9600 bit/s
apr 18 18:01:43.22: [11872]: REMOTE max A4 page width (215 mm)
apr 18 18:01:43.22: [11872]: REMOTE max unlimited page length
apr 18 18:01:43.22: [11872]: REMOTE best vres 7.7 line/mm
apr 18 18:01:43.22: [11872]: REMOTE format support: MH, MR
apr 18 18:01:43.22: [11872]: REMOTE best 20 ms, 10 ms/scanline
apr 18 18:01:43.22: [11872]: USE 9600 bit/s
apr 18 18:01:43.22: [11872]: SEND file "docq/doc25.ps;c1"
apr 18 18:01:43.22: [11872]: USE A4 page width (215 mm)
apr 18 18:01:43.22: [11872]: USE unlimited page length
apr 18 18:01:43.22: [11872]: USE 7.7 line/mm
apr 18 18:01:43.22: [11872]: USE 2-D MR
apr 18 18:01:43.22: [11872]: USE 10 ms/scanline
apr 18 18:01:43.22: [11872]: SEND training at v.29 9600 bit/s
apr 18 18:01:43.22: [11872]: DELAY 70 ms
apr 18 18:01:43.29: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:01:43.34: [11872]: --> [7:CONNECT]
apr 18 18:01:43.37: [11872]: --> [7:CONNECT]
apr 18 18:01:45.53: [11872]: --> [2:OK]
apr 18 18:01:45.53: [11872]: DELAY 70 ms
apr 18 18:01:45.61: [11872]: <-- [10:AT+FTM=96\r]
apr 18 18:01:46.12: [11872]: --> [7:CONNECT]
apr 18 18:01:47.67: [11872]: --> [2:OK]
apr 18 18:01:47.67: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:01:48.17: [11872]: --> [7:CONNECT]
apr 18 18:01:49.34: [11872]: --> [2:OK]
apr 18 18:01:49.34: [11872]: TRAINING succeeded
apr 18 18:01:49.34: [11872]: DELAY 70 ms
apr 18 18:01:49.41: [11872]: <-- [10:AT+FTM=96\r]
apr 18 18:01:50.00: [11872]: --> [7:CONNECT]
apr 18 18:01:50.00: [11872]: SEND begin page
apr 18 18:01:50.04: [11872]: Reading MMR-compressed image file
apr 18 18:01:50.07: [11872]: SENT 74 bytes of data
apr 18 18:01:50.07: [11872]: SENT 71 bytes of data
.......................................
.......................................
apr 18 18:02:12.13: [11872]: SENT 72 bytes of data
apr 18 18:02:12.13: [11872]: SENT 72 bytes of data
apr 18 18:02:12.13: [11872]: SENT 60 bytes of data
apr 18 18:02:12.13: [11872]: SEND 2D RTC
apr 18 18:02:12.13: [11872]: SEND end page
apr 18 18:02:27.01: [11872]: --> [2:OK]
apr 18 18:02:27.01: [11872]: DELAY 70 ms
apr 18 18:02:27.08: [11872]: SEND send MPS (more pages, same document)
apr 18 18:02:27.08: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:27.13: [11872]: --> [7:CONNECT]
apr 18 18:02:28.44: [11872]: --> [2:OK]
apr 18 18:02:28.44: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:02:31.55: [11872]: --> [0:]
apr 18 18:02:31.55: [11872]: MODEM <Empty line>
apr 18 18:02:31.75: [11872]: MODEM <Timeout>
apr 18 18:02:31.75: [11872]: SEND send MPS (more pages, same document)
apr 18 18:02:31.75: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:31.80: [11872]: --> [7:CONNECT]
apr 18 18:02:33.12: [11872]: --> [2:OK]
apr 18 18:02:33.12: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:02:36.22: [11872]: --> [0:]
apr 18 18:02:36.22: [11872]: MODEM <Empty line>
apr 18 18:02:36.43: [11872]: MODEM <Timeout>
apr 18 18:02:36.43: [11872]: SEND send MPS (more pages, same document)
apr 18 18:02:36.43: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:36.47: [11872]: --> [7:CONNECT]
apr 18 18:02:37.79: [11872]: --> [2:OK]
apr 18 18:02:37.79: [11872]: <-- [9:AT+FRH=3\r]
apr 18 18:02:40.89: [11872]: --> [0:]
apr 18 18:02:40.89: [11872]: MODEM <Empty line>
apr 18 18:02:41.10: [11872]: MODEM <Timeout>
apr 18 18:02:41.10: [11872]: No response to MPS repeated 3 tries
apr 18 18:02:41.10: [11872]: <-- [9:AT+FTH=3\r]
apr 18 18:02:41.15: [11872]: --> [7:CONNECT]
apr 18 18:02:42.46: [11872]: --> [2:OK]
apr 18 18:02:42.46: [11872]: SEND FAILED: JOB 25 DEST XXXXXXXX ERR No
response to MPS repeated 3 tries; too many attempts to dial
apr 18 18:02:42.46: [11872]: <-- [5:ATH0\r]
apr 18 18:02:42.89: [11872]: --> [10:NO CARRIER]
apr 18 18:02:42.89: [11872]: MODEM No carrier
apr 18 18:02:42.89: [11872]: SESSION END

------- Unsent job status -------
      Destination: XXXXXXXX
            JobID: 25
          GroupID: 25
           Sender: faxuser
         Mailaddr: xxxxx@xxxxxxxxxxx <mailto:xxxxx@xxxxxxxxxxx>
           CommID: 000000440
            Modem: any
   Submitted From: 192.168.0.11
       Page Width: 194  (mm)
      Page Length: 281 (mm)
       Resolution: 213 (lpi)
           Status: No response to MPS repeated 3 tries; too many 
attempts to
dial
          Dialogs: 2
            Dials: 0
            Calls: 2
            Pages: 0
         TotPages: 7
         Attempts: 2
           Dirnum:


---------------------------------------------------

can anyone help me, please??

Thank You
Bye

    

--
Nota di riservatezza: il presente messaggio, corredato dei relativi allegati, contiene informazioni da considerarsi strettamente riservate ed è destinato esclusivamente al destinatario sopra indicato, il quale è l'unico autorizzato ad usarlo, copiarlo e, sotto la propria responsabilità, diffonderlo. Chiunque ricevesse questo messaggio per errore o comunque lo leggesse senza esserne legittimato è avvertito che trattenerlo, copiarlo, divulgarlo, distribuirlo a persone diverse dal destinatario è severamente proibito ed è pregato di rinviarlo immediatamente al mittente distruggendo l'originale. Grazie.

Confidentiality notice: this message, together with its annexes, contains information to be deemed strictly confidential and is destined only to the addressee(s) identified above who only may use, copy and, under his/their responsibility, further disseminate it. If anyone received this message by mistake or reads it without entitlement is forewarned that keeping, copying, disseminating or distributing this message to persons other than the addressee(s) is strictly forbidden and is asked to transmit it immediately to the sender and to erase the original message received. Thank you.

____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*