Re: [hylafax-users] RSPREC error/got DCN (code 51) since hylafax upgrade

["Jeff Brickwell" <t800949@xxxxxxxxx>]

Same modems / PABX magic.  Just to be sure, below is a log from a
successful send from the modem on the same line on the term server on
the existing hylafax server.

What's different is the (reverse terminal server) software I'm using
as the layer between /dev/modem30 and the terminal server TCP port.
On the HP-UX server I'm using HPUX ocd (part of the ddfa suite) and on
the Linux server I'm unsing a modified version of ttyd.  While I
wouldn't expect this to make a difference....

Regards
Jeff

----------Session log for successful example on same line----
Jan 16 16:12:52.47: [13556]: SESSION BEGIN 001357198 XXXXXXXXXXX
Jan 16 16:12:52.47: [13556]: HylaFAX (tm) Version 4.2.1
Jan 16 16:12:52.47: [13556]: SEND FAX: JOB 1149713 DEST XXXXXXXXXX
COMMID 001357198 DEVICE '/dev/modem30'
Jan 16 16:12:52.47: [13556]: <-- [10:AT+FTBC=0\r]
Jan 16 16:12:52.64: [13556]: --> [2:OK]
Jan 16 16:12:52.64: [13556]: <-- [10:AT+FBOR=0\r]
Jan 16 16:12:52.78: [13556]: --> [2:OK]
Jan 16 16:12:52.78: [13556]: <-- [13:AT+FPHCTO=30\r]
Jan 16 16:12:52.94: [13556]: --> [2:OK]
Jan 16 16:12:52.94: [13556]: <-- [24:AT+FDCC=1,7,2,2,0,0,0,0\r]
Jan 16 16:12:53.08: [13556]: --> [5:ERROR]
Jan 16 16:12:53.08: [13556]: MODEM Command error
Jan 16 16:12:53.08: [13556]: DIAL XXXXXXXXXX
Jan 16 16:12:53.08: [13556]: <-- [15:ATDTXXXXXXXXXX\r]
Jan 16 16:13:05.70: [13556]: --> [5:+FCON]
Jan 16 16:13:07.09: [13556]: --> [65:+FNSF:00 00 25 00 00 00 92 10 4D
02 00 58 00 28 B8 A0 80 80 B1 60]
Jan 16 16:13:07.09: [13556]: REMOTE NSF "00 00 25 00 00 00 92 10 4D 02
00 58 00 28 B8 A0 80 80 B1 60"
Jan 16 16:13:07.09: [13556]: NSF remote fax equipment: Ricoh
Jan 16 16:13:07.62: [13556]: --> [50:+FNSF:00 00 25 01 53 4E 52 49 41
43 20 55 48 50 54]
Jan 16 16:13:07.62: [13556]: REMOTE NSF "00 00 25 01 53 4E 52 49 41 43
20 55 48 50 54"
Jan 16 16:13:07.62: [13556]: NSF remote fax equipment: Ricoh
Jan 16 16:13:07.62: [13556]: NSF remote station ID: "THE SUN PLACE H"
Jan 16 16:13:08.32: [13556]: --> [28:+FCSI:"       XX X XXXXXXXX"]
Jan 16 16:13:08.32: [13556]: REMOTE CSI "XX X XXXXXXXX"
Jan 16 16:13:08.75: [13556]: --> [21:+FDIS:1,5,2,2,3,1,0,3]
Jan 16 16:13:08.75: [13556]: --> [2:OK]
Jan 16 16:13:08.75: [13556]: REMOTE best rate 14400 bit/s
Jan 16 16:13:08.75: [13556]: REMOTE max A3 page width (303 mm)
Jan 16 16:13:08.75: [13556]: REMOTE max unlimited page length
Jan 16 16:13:08.75: [13556]: REMOTE best vres 7.7 line/mm
Jan 16 16:13:08.75: [13556]: REMOTE best format 2-D MMR
Jan 16 16:13:08.75: [13556]: REMOTE supports T.30 Annex A, 64-byte ECM
Jan 16 16:13:08.75: [13556]: REMOTE best 10 ms/scanline
Jan 16 16:13:08.75: [13556]: USE 14400 bit/s
Jan 16 16:13:08.75: [13556]: USE 10 ms/scanline
Jan 16 16:13:08.75: [13556]: SEND file "docq/doc1149720.ps;01"
Jan 16 16:13:08.75: [13556]: USE A4 page width (215 mm)
Jan 16 16:13:08.75: [13556]: USE unlimited page length
Jan 16 16:13:08.75: [13556]: USE 7.7 line/mm
Jan 16 16:13:08.75: [13556]: USE 1-D MH
Jan 16 16:13:08.75: [13556]: <-- [24:AT+FDIS=1,5,0,2,0,0,0,3\r]
Jan 16 16:13:08.90: [13556]: --> [2:OK]
Jan 16 16:13:08.90: [13556]: <-- [7:AT+FDT\r]
Jan 16 16:13:16.42: [13556]: --> [21:+FDCS:1,5,0,2,0,0,0,3]
Jan 16 16:13:16.99: [13556]: --> [7:CONNECT]
Jan 16 16:13:16.99: [13556]: SEND wait for XON
Jan 16 16:13:16.99: [13556]: --> [1:]
Jan 16 16:13:16.99: [13556]: SEND begin page
Jan 16 16:13:16.99: [13556]: <-- data [1027]

(snipped data lines)

Jan 16 16:14:03.21: [13556]: <-- data [1024]
Jan 16 16:14:03.21: [13556]: <-- data [122]
Jan 16 16:14:03.21: [13556]: SENT 77946 bytes of data
Jan 16 16:14:03.21: [13556]: <-- data [2]
Jan 16 16:14:03.21: [13556]: SEND end page
Jan 16 16:14:11.46: [13556]: --> [2:OK]
Jan 16 16:14:11.46: [13556]: SEND send EOP (no more pages or documents)
Jan 16 16:14:11.46: [13556]: <-- [9:AT+FET=2\r]
Jan 16 16:14:14.24: [13556]: --> [7:+FPTS:1]
Jan 16 16:14:15.85: [13556]: --> [7:+FHNG:0]
Jan 16 16:14:15.85: [13556]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Jan 16 16:14:15.85: [13556]: SEND recv MCF (message confirmation)
Jan 16 16:14:15.85: [13556]: SEND FAX (001357198): FROM
jeffb@xxxxxxxxxx TO XXXXXXXXXX (docq/doc1149720.ps;01 sent in 1:07)
Jan 16 16:14:15.85: [13556]: SEND FAX (001357198): FROM
jeffb@xxxxxxxxxx TO XXXXXXXXXX (page 1 of 1 sent in 1:07)
Jan 16 16:14:16.87: [13556]: <-- [5:ATH0\r]
Jan 16 16:14:16.87: [13556]: --> [2:OK]
Jan 16 16:14:16.89: [13556]: SESSION END



On 14/02/07, Lee Howard <faxguy@xxxxxxxxxxxxxxxx> wrote:
> Are you positive that you're not using different modems here?  Or maybe
> different modem revisions or something.  Because it really does appear
> that your modem suddenly gained the ability to use ECM.
>
> Lee.
>
>
> Jeff Brickwell wrote:
>
> > -------------------Session log for error case
> > ----------------------------
> >
> > Feb 13 09:11:21.58: [ 8202]: SESSION BEGIN 000000005 XXXXXXXXXXX
> > Feb 13 09:11:21.58: [ 8202]: HylaFAX (tm) Version 4.3.1
> > Feb 13 09:11:21.58: [ 8202]: SEND FAX: JOB 8 DEST XXXXXXXXXX COMMID
> > 000000005 DEVICE '/dev/tmodem30' FROM 'uucp ' USER uucp
> > Feb 13 09:11:21.58: [ 8202]: <-- [10:AT+FTBC=0\r]
> > Feb 13 09:11:21.91: [ 8202]: --> [2:OK]
> > Feb 13 09:11:21.91: [ 8202]: <-- [10:AT+FBOR=0\r]
> > Feb 13 09:11:22.19: [ 8202]: --> [2:OK]
> > Feb 13 09:11:22.19: [ 8202]: <-- [13:AT+FPHCTO=30\r]
> > Feb 13 09:11:22.46: [ 8202]: --> [2:OK]
> > Feb 13 09:11:22.46: [ 8202]: <-- [24:AT+FDCC=1,5,2,2,3,1,0,0\r]
> > Feb 13 09:11:22.73: [ 8202]: --> [2:OK]
> > Feb 13 09:11:22.75: [ 8202]: DIAL XXXXXXXXXX
> > Feb 13 09:11:22.75: [ 8202]: <-- [15:ATDTXXXXXXXXXX\r]
> > Feb 13 09:11:35.34: [ 8202]: --> [5:+FCON]
> > Feb 13 09:11:37.27: [ 8202]: --> [110:+FNSF:00 00 11 80 00 8A 49 10 41
> > 6C 62 65 72 74 20 41 6E 69 6D 61 6C 20 48 6F 00 89 00 80 80 80 06 01
> > 01 01 01]
> > Feb 13 09:11:37.27: [ 8202]: REMOTE NSF "00 00 11 80 00 8A 49 10 41 6C
> > 62 65 72 74 20 41 6E 69 6D 61 6C 20 48 6F 00 89 00 80 80 80 06 01 01
> > 01 01"
> > Feb 13 09:11:37.27: [ 8202]: NSF remote fax equipment: Canon Laser
> > Class 9000 Series
> > Feb 13 09:11:37.27: [ 8202]: NSF remote station ID: "Albert Place Hou"
> > Feb 13 09:11:38.00: [ 8202]: --> [28:+FCSI:" XXXXXXXXXX"]
> > Feb 13 09:11:38.00: [ 8202]: REMOTE CSI "XXXXXXXXXX"
> > Feb 13 09:11:38.43: [ 8202]: --> [21:+FDIS:1,5,0,2,3,1,0,3]
> > Feb 13 09:11:38.43: [ 8202]: --> [2:OK]
> > Feb 13 09:11:38.43: [ 8202]: REMOTE best rate 14400 bit/s
> > Feb 13 09:11:38.43: [ 8202]: REMOTE max A4 page width (215 mm)
> > Feb 13 09:11:38.43: [ 8202]: REMOTE max unlimited page length
> > Feb 13 09:11:38.43: [ 8202]: REMOTE best vres 7.7 line/mm
> > Feb 13 09:11:38.43: [ 8202]: REMOTE format support: MH, MMR
> > Feb 13 09:11:38.43: [ 8202]: REMOTE supports T.30 Annex A, 64-byte ECM
> > Feb 13 09:11:38.43: [ 8202]: REMOTE best 10 ms/scanline
> > Feb 13 09:11:38.43: [ 8202]: USE 14400 bit/s
> > Feb 13 09:11:38.43: [ 8202]: USE error correction mode
> > Feb 13 09:11:38.43: [ 8202]: SEND file "docq/doc8.ps;c1"
> > Feb 13 09:11:38.44: [ 8202]: USE A4 page width (215 mm)
> > Feb 13 09:11:38.44: [ 8202]: USE unlimited page length
> > Feb 13 09:11:38.44: [ 8202]: USE 7.7 line/mm
> > Feb 13 09:11:38.44: [ 8202]: USE 2-D MMR
> > Feb 13 09:11:38.44: [ 8202]: USE 0 ms/scanline
> > Feb 13 09:11:38.44: [ 8202]: <-- [24:AT+FDIS=1,5,0,2,3,1,0,0\r]
> > Feb 13 09:11:38.70: [ 8202]: --> [2:OK]
> > Feb 13 09:11:38.70: [ 8202]: <-- [7:AT+FDT\r]
> > Feb 13 09:11:45.97: [ 8202]: --> [21:+FDCS:1,5,0,2,3,1,0,0]
> > Feb 13 09:11:45.97: [ 8202]: --> [7:CONNECT]
> > Feb 13 09:11:45.97: [ 8202]: SEND wait for XON
> > Feb 13 09:11:45.97: [ 8202]: --> [1:]
> > Feb 13 09:11:45.97: [ 8202]: SEND begin page
> > Feb 13 09:11:45.99: [ 8202]: <-- data [1038]
>
> (snipped)
>
> > Feb 13 09:11:47.31: [ 8202]: <-- data [821]
> > Feb 13 09:11:47.31: [ 8202]: SENT 11058 bytes of data
> > Feb 13 09:11:47.31: [ 8202]: <-- data [2]
> > Feb 13 09:11:47.66: [ 8202]: SEND end page
> > Feb 13 09:11:53.47: [ 8202]: --> [2:OK]
> > Feb 13 09:11:53.47: [ 8202]: SEND send EOP (no more pages or documents)
> > Feb 13 09:11:53.47: [ 8202]: <-- [9:AT+FET=2\r]
> > Feb 13 09:11:56.69: [ 8202]: --> [8:+FHNG:51]
> > Feb 13 09:11:56.69: [ 8202]: REMOTE HANGUP: RSPREC error/got DCN (code
> > 51)
> > Feb 13 09:11:56.69: [ 8202]: <-- [5:ATH0\r]
> > Feb 13 09:11:56.69: [ 8202]: --> [2:OK]
> > Feb 13 09:11:56.69: [ 8202]: SESSION END
> >
> > -------------------Session log for non-error case
> > ------------------------
> >
> > Feb 13 09:18:32.47: [23039]: SESSION BEGIN 001435920 XXXXXXXXXXX
> > Feb 13 09:18:32.47: [23039]: HylaFAX (tm) Version 4.2.1
> > Feb 13 09:18:32.48: [23039]: SEND FAX: JOB 1216416 DEST XXXXXXXXXX
> > COMMID 001435920 DEVICE '/dev/modem17'
> > Feb 13 09:18:32.48: [23039]: <-- [10:AT+FTBC=0\r]
> > Feb 13 09:18:32.63: [23039]: --> [2:OK]
> > Feb 13 09:18:32.63: [23039]: <-- [10:AT+FBOR=0\r]
> > Feb 13 09:18:32.79: [23039]: --> [2:OK]
> > Feb 13 09:18:32.79: [23039]: <-- [13:AT+FPHCTO=30\r]
> > Feb 13 09:18:32.94: [23039]: --> [2:OK]
> > Feb 13 09:18:32.94: [23039]: <-- [24:AT+FDCC=1,7,2,2,0,0,0,0\r]
> > Feb 13 09:18:33.09: [23039]: --> [5:ERROR]
> > Feb 13 09:18:33.09: [23039]: MODEM Command error
> > Feb 13 09:18:33.09: [23039]: DIAL XXXXXXXXXX
> > Feb 13 09:18:33.09: [23039]: <-- [15:ATDTXXXXXXXXXX\r]
> > Feb 13 09:18:45.54: [23039]: --> [5:+FCON]
> > Feb 13 09:18:47.47: [23039]: --> [110:+FNSF:00 00 11 80 00 8A 49 10 41
> > 6C 62 65 72 74 20 41 6E 69 6D 61 6C 20 48 6F 00 89 00 80 80 80 06 01
> > 01 01 01]
> > Feb 13 09:18:47.47: [23039]: REMOTE NSF "00 00 11 80 00 8A 49 10 41 6C
> > 62 65 72 74 20 41 6E 69 6D 61 6C 20 48 6F 00 89 00 80 80 80 06 01 01
> > 01 01"
> > Feb 13 09:18:47.47: [23039]: NSF remote fax equipment: Canon Laser
> > Class 9000 Series
> > Feb 13 09:18:47.47: [23039]: NSF remote station ID: "Albert Place Hou"
> > Feb 13 09:18:48.21: [23039]: --> [28:+FCSI:" XXXXXXXXXX"]
> > Feb 13 09:18:48.21: [23039]: REMOTE CSI "XXXXXXXXXX"
> > Feb 13 09:18:48.63: [23039]: --> [21:+FDIS:1,5,0,2,3,1,0,3]
> > Feb 13 09:18:48.63: [23039]: --> [2:OK]
> > Feb 13 09:18:48.63: [23039]: REMOTE best rate 14400 bit/s
> > Feb 13 09:18:48.63: [23039]: REMOTE max A4 page width (215 mm)
> > Feb 13 09:18:48.63: [23039]: REMOTE max unlimited page length
> > Feb 13 09:18:48.63: [23039]: REMOTE best vres 7.7 line/mm
> > Feb 13 09:18:48.63: [23039]: REMOTE best format 2-D MMR
> > Feb 13 09:18:48.63: [23039]: REMOTE supports T.30 Annex A, 64-byte ECM
> > Feb 13 09:18:48.63: [23039]: REMOTE best 10 ms/scanline
> > Feb 13 09:18:48.63: [23039]: USE 14400 bit/s
> > Feb 13 09:18:48.63: [23039]: USE 10 ms/scanline
> > Feb 13 09:18:48.63: [23039]: SEND file "docq/doc1216423.ps;01"
> > Feb 13 09:18:48.63: [23039]: USE A4 page width (215 mm)
> > Feb 13 09:18:48.63: [23039]: USE unlimited page length
> > Feb 13 09:18:48.63: [23039]: USE 7.7 line/mm
> > Feb 13 09:18:48.63: [23039]: USE 1-D MH
> > Feb 13 09:18:48.63: [23039]: <-- [24:AT+FDIS=1,5,0,2,0,0,0,3\r]
> > Feb 13 09:18:48.79: [23039]: --> [2:OK]
> > Feb 13 09:18:48.79: [23039]: <-- [7:AT+FDT\r]
> > Feb 13 09:18:55.98: [23039]: --> [21:+FDCS:1,5,0,2,0,0,0,3]
> > Feb 13 09:18:56.56: [23039]: --> [7:CONNECT]
> > Feb 13 09:18:56.56: [23039]: SEND wait for XON
> > Feb 13 09:18:56.56: [23039]: --> [1:]
> > Feb 13 09:18:56.56: [23039]: SEND begin page
> > Feb 13 09:18:56.56: [23039]: <-- data [1028]
> > (snipped)
> > Feb 13 09:18:56.57: [23039]: <-- data [1027]
> > Feb 13 09:18:56.57: [23039]: <-- data [38]
> > Feb 13 09:18:56.57: [23039]: SENT 28710 bytes of data
> > Feb 13 09:18:56.57: [23039]: <-- data [2]
> > Feb 13 09:18:56.57: [23039]: SEND end page
> > Feb 13 09:19:26.27: [23039]: --> [2:OK]
> > Feb 13 09:19:26.27: [23039]: SEND send EOP (no more pages or documents)
> > Feb 13 09:19:26.27: [23039]: <-- [9:AT+FET=2\r]
> > Feb 13 09:19:29.31: [23039]: --> [7:+FPTS:1]
> > Feb 13 09:19:30.91: [23039]: --> [7:+FHNG:0]
> > Feb 13 09:19:30.91: [23039]: REMOTE HANGUP: Normal and proper end of
> > connection (code 0)
> > Feb 13 09:19:30.91: [23039]: SEND recv MCF (message confirmation)
> > Feb 13 09:19:30.92: [23039]: SEND FAX (001435920): FROM
> > jeffb@xxxxxxxxxxxxx TO XXXXXXXXXX (docq/doc1216423.ps;01 sent in 0:42)
> > Feb 13 09:19:30.92: [23039]: SEND FAX (001435920): FROM
> > jeffb@xxxxxxxxxxxxx TO XXXXXXXXXX (page 1 of 1 sent in 0:42)
> > Feb 13 09:19:31.94: [23039]: <-- [5:ATH0\r]
> > Feb 13 09:19:31.94: [23039]: --> [2:OK]
> > Feb 13 09:19:31.95: [23039]: SESSION END

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*