Re: [hylafax-users] GVC Fax 14400 V.42bis/MNP5 Modem Problem with Hylafax

[Schorn@xxxxxxxxxxx]

Hello Michael,

thank you for your help. I tested your config file, but the failure still is
there.
When you take a look into the log, I can't see where the modem switched to class
1

Jun 14 22:57:15.07: [ 7041]: SESSION BEGIN 00000076 49222415
Jun 14 22:57:15.07: [ 7041]: HylaFAX (tm) Version 4.1
Jun 14 22:57:15.07: [ 7041]: SEND FAX: JOB 30 DEST ############## COMMID
00000076
Jun 14 22:57:15.07: [ 7041]: DEVICE '/dev/ttyS0'
Jun 14 22:57:15.07: [ 7041]: DELAY 75 ms
Jun 14 22:57:15.14: [ 7041]: DELAY 2600 ms
Jun 14 22:57:17.74: [ 7041]: <-- [4:ATZ\r]
Jun 14 22:57:18.35: [ 7041]: --> [3:ATZ]
Jun 14 22:57:18.35: [ 7041]: --> [2:OK]
Jun 14 22:57:18.35: [ 7041]: <-- [5:ATE0\r]
Jun 14 22:57:18.58: [ 7041]: --> [4:ATE0]
Jun 14 22:57:18.59: [ 7041]: --> [2:OK]
Jun 14 22:57:18.59: [ 7041]: <-- [5:ATV1\r]
Jun 14 22:57:18.82: [ 7041]: --> [2:OK]
Jun 14 22:57:18.82: [ 7041]: <-- [5:ATQ0\r]
Jun 14 22:57:19.04: [ 7041]: --> [2:OK]
Jun 14 22:57:19.04: [ 7041]: <-- [7:ATS0=0\r]
Jun 14 22:57:19.27: [ 7041]: --> [2:OK]
Jun 14 22:57:19.27: [ 7041]: <-- [7:ATS8=2\r]
Jun 14 22:57:19.50: [ 7041]: --> [2:OK]
Jun 14 22:57:19.50: [ 7041]: <-- [8:ATS7=60\r]
Jun 14 22:57:19.73: [ 7041]: --> [2:OK]
Jun 14 22:57:19.73: [ 7041]: <-- [6:AT\Q3\r]
Jun 14 22:57:19.96: [ 7041]: --> [2:OK]
Jun 14 22:57:19.96: [ 7041]: <-- [6:AT&D3\r]
Jun 14 22:57:20.19: [ 7041]: --> [2:OK]
Jun 14 22:57:20.19: [ 7041]: <-- [6:AT&C1\r]
Jun 14 22:57:20.42: [ 7041]: --> [2:OK]
Jun 14 22:57:20.42: [ 7041]: <-- [12:AT+FCLASS=2\r]
Jun 14 22:57:20.65: [ 7041]: --> [2:OK]
Jun 14 22:57:20.65: [ 7041]: <-- [10:AT+FBOR=0\r]
Jun 14 22:57:20.88: [ 7041]: --> [2:OK]
Jun 14 22:57:20.88: [ 7041]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Jun 14 22:57:21.12: [ 7041]: --> [2:OK]
Jun 14 22:57:21.12: [ 7041]: <-- [7:ATL0M1\r]
Jun 14 22:57:21.36: [ 7041]: --> [2:OK]
Jun 14 22:57:21.36: [ 7041]: <-- [12:AT+FCLASS=2\r]
Jun 14 22:57:21.69: [ 7041]: --> [2:OK]
Jun 14 22:57:21.69: [ 7041]: <-- [10:AT+FBOR=0\r]
Jun 14 22:57:22.01: [ 7041]: --> [2:OK]
Jun 14 22:57:22.01: [ 7041]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Jun 14 22:57:22.35: [ 7041]: --> [2:OK]
Jun 14 22:57:22.35: [ 7041]: <-- [25:AT+FLID="Schorn, ############ "\r]
Jun 14 22:57:22.70: [ 7041]: --> [2:OK]
Jun 14 22:57:22.70: [ 7041]: DIAL 15
Jun 14 22:57:22.70: [ 7041]: <-- [9:ATX3DT15\r]
Jun 14 22:57:29.24: [ 7041]: --> [3:CED]
Jun 14 22:57:34.62: [ 7041]: --> [5:+FCON]
Jun 14 22:57:34.62: [ 7041]: --> [40:+FNSF: 00 00 56 55 55 00 80 B0 80 00 00 ]
Jun 14 22:57:34.62: [ 7041]: REMOTE NSF " 00 00 56 55 55 00 80 B0 80 00 00"
Jun 14 22:57:34.63: [ 7041]: NSF remote fax equipment: Brother
Jun 14 22:57:34.63: [ 7041]: --> [29:+FCSI: "     +49 2224 9##########"]
Jun 14 22:57:34.63: [ 7041]: REMOTE CSI "+49 2224 9#########"
Jun 14 22:57:34.63: [ 7041]: --> [22:+FDIS: 1,3,0,2,0,0,0,3]
Jun 14 22:57:34.63: [ 7041]: --> [2:OK]
Jun 14 22:57:34.63: [ 7041]: REMOTE best rate 9600 bit/s
Jun 14 22:57:34.63: [ 7041]: REMOTE max page width 1728 pixels in 215 mm
Jun 14 22:57:34.63: [ 7041]: REMOTE max unlimited page length 
Jun 14 22:57:34.63: [ 7041]: REMOTE best vres 7.7 line/mm
Jun 14 22:57:34.63: [ 7041]: REMOTE best format 1-D MR
Jun 14 22:57:34.63: [ 7041]: REMOTE best 10 ms/scanline
Jun 14 22:57:34.63: [ 7041]: USE 9600 bit/s
Jun 14 22:57:34.63: [ 7041]: USE 10 ms/scanline
Jun 14 22:57:34.63: [ 7041]: SEND file "docq/doc30.ps;00"
Jun 14 22:57:34.63: [ 7041]: USE page width 1728 pixels in 215 mm
Jun 14 22:57:34.63: [ 7041]: USE unlimited page length
Jun 14 22:57:34.63: [ 7041]: USE 3.85 line/mm
Jun 14 22:57:34.63: [ 7041]: USE 1-D MR
Jun 14 22:57:34.63: [ 7041]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,3\r]
Jun 14 22:57:36.00: [ 7041]: --> [9:+FHNG: 40]
Jun 14 22:57:36.00: [ 7041]: REMOTE HANGUP: Unspecified Transmit Phase C error
(code 40)
Jun 14 22:57:36.00: [ 7041]: --> [2:OK]
Jun 14 22:57:36.00: [ 7041]: <-- [7:AT+FDT\r]
Jun 14 22:57:36.42: [ 7041]: --> [10:NO CARRIER]
Jun 14 22:57:36.42: [ 7041]: MODEM No carrier
Jun 14 22:57:36.42: [ 7041]: <-- [5:ATH0\r]
Jun 14 22:57:37.12: [ 7041]: --> [2:OK]
Jun 14 22:57:37.13: [ 7041]: SESSION END


How can I bring the modem to class 1, even when the AT+FCLASS shows, thas this
is not supported
regards
Heribert




On Sun, 13 Jun 2004 23:15:24 -0400
"Michael J. Pedersen" <pedermj@xxxxxxxxxxx> wrote:

> On Sun, Jun 13, 2004 at 06:29:06PM -0700, Lee Howard wrote:
> > Here are the relevant parts of the post:
> > ATI0	RESULT = "OK"	RESPONSE = "242"
> > ATI1	RESULT = "OK"	RESPONSE = "175"
> > ATI2	RESULT = "OK"	RESPONSE = "OK"
> > ATI3	RESULT = "OK"	RESPONSE = "E.C.  Version : 7.1"
> 
> Thank you. I can pretty safely say that that modem is a GVC 14.4
> modem.
> 
> I'm kind of suspicious of the output, though. For comparison, here's the
> output from a GVC 28.8 ATI command set.
> 
> ATI0
> 288
> 
> OK
> 
> ATI1
> 173
> 
> F1128V/R6  V6.18.13
> 
> OK
> 
> ATI2
> OK
> ATI3
> E.C. Version: T
> ATI4
> 
> F1128V/R6  V6.18.13
> 
> MODEM CHIP: ROCKWELL RC288DPi
> 
> FAX CLASS 1 AND FAX CLASS 2
> 
> OK
> AT+FCLASS=?
> 0,1,2
> 
> OK
> 
> Notice the carriage returns in responses. Dunno if that will matter to
> HylaFAX or not. However, it is most definitely class 1 and 2 capable. In
> fact all GVC modems that were class 2 capable were class 1 capable.
> 
> I'm attaching my config.ttyS1 in hope that it
> will help.
> 
> -----config.ttyS1
> 
> # $Id: gvc-288-2,v 1.3 2002/04/07 20:29:26 darren Exp $
> #
> # HylaFAX Facsimile Software
> #
> # Copyright (c) 1990-1996 Sam Leffler
> # Copyright (c) 1991-1996 Silicon Graphics, Inc.
> # HylaFAX is a trademark of Silicon Graphics, Inc.
> # 
> # Permission to use, copy, modify, distribute, and sell this software and 
> # its documentation for any purpose is hereby granted without fee, provided
> # that (i) the above copyright notices and this permission notice appear in
> # all copies of the software and related documentation, and (ii) the names of
> # Sam Leffler and Silicon Graphics may not be used in any advertising or
> # publicity relating to the software without the specific, prior written
> # permission of Sam Leffler and Silicon Graphics.
> # 
> # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
> # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
> # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
> # 
> # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
> # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
> # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
> # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
> # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
> # OF THIS SOFTWARE.
> #
> 
> #
> # Configuration for a GVC MAXTech 288 RC288DPi-based Class 2 modem.
> # Tested with firmware rev KA1131-00.
> #
> # NB: DCD is toggled at page end during transmits; this can
> #     cause problems on systems where it's not possible to
> #     set CLOCAL and also enable RTS/CTS flow control.
> #
> #
> CountryCode:		1
> AreaCode:		908
> FAXNumber:		1-908-435-3711
> LongDistancePrefix:	1
> InternationalPrefix:	011
> DialStringRules:	etc/dialrules
> ServerTracing:		0x08501
> SessionTracing:		0x08501
> RecvFileMode:		0640
> LogFileMode:		0640
> DeviceMode:		0660
> RingsBeforeAnswer:	1
> SpeakerVolume:		off
> GettyArgs:		"-r -b %l"
> LocalIdentifier:	"Michael Pedersen"
> TagLineFormat:		"From %%l|%c|Page %%P of %%T"
> MaxRecvPages:		25
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType:		Class2		# use class 1 interface
> ModemRate:		19200		# locked for fax sending&receiving
> ModemFlowControl:	rtscts		# default
> #
> ModemNoFlowCmd:		AT\Q0		# disable flow control cmd
> ModemSoftFlowCmd:	AT\Q1		# software flow control cmd
> ModemHardFlowCmd:	AT\Q3		# hardware flow control cmd
> ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
> ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
> ModemSetupAACmd:	AT+FAA=1	# enable adaptive-answer in Class 2
> #
> ModemRecvFillOrder:	MSB2LSB		# bit order of received facsimile
> ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
> #
> ModemDialCmd:		ATDT%s		# T for tone dialing
> #
> # Chip locks the line rate and switches to xon/xoff flow
> # control when receiving facsimile--we must follow suit.
> #
> ModemAnswerFaxBeginCmd:	"<19200><xon>"	# lock line rate & switch flow control
> #
> Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv
> #
> # These are known to not be implemented on the GVC with the above
> # firmware rev.  Sending them to the modem does not harm anything,
> # but generates an ERROR result that can generate questions from the
> # naive--so we disable them here.
> #
> Class2TBCCmd:		none		# setup stream mode
> Class2PHCTOCmd:		none		# set phase C timeout parameter
> 
> --end config.ttyS1
> -- 
> Michael J. Pedersen
> My IM IDs: Jabber/pedersen@xxxxxxxxxxxxxx, ICQ/103345809, AIM/pedermj022171
>            Yahoo/pedermj2002, MSN/pedermj022171@xxxxxxxxxxx
> My GnuPG KeyID: 6CB0A96C       My Public Key Available At: www.keyserver.net
> My GnuPG Key Fingerprint: E8F0 920F EB2F 7FDE DF4E  23CC 2CEB 8E6F 6CB0 A96C
> 

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*