[hylafax-users] GVC Fax 14400 V.42bis/MNP5 Modem Problem with Hylafax

[Heribert Schorn <h.schorn@xxxxxx>]

Hello

i try to use the GVC Fax 14400 V42bis/MNP5 Modem with Hylafax. But I can't send
any Fax. 
My Linux System is SUSE 8.0 with kernel 2.4.18 and hylafax 4.1-200.
The installation of the Software seems to be succsessfull.

probemodem gets me the following :

Now we are going to probe the tty port.  This takes a few seconds,
so be patient.  Note that if you do not have the modem cabled to
the port, or the modem is turned off, this may hang (just go and
cable up the modem or turn it on, or whatever).

Probing for best speed to talk to modem: 38400 OK.

This looks like a Class 2 modem.

ATI0	RESULT = "OK"	RESPONSE = "242"
ATI1	RESULT = "OK"	RESPONSE = "175"
ATI2	RESULT = "OK"	RESPONSE = "OK"
ATI3	RESULT = "OK"	RESPONSE = "E.C.  Version : 7.1"

Class 2 stuff...

AT+FCLASS=?	RESULT = "OK"	RESPONSE = "0,2"
AT+FCLASS?	RESULT = "OK"	RESPONSE = "2"
AT+FCLASS=0	RESULT = "OK"	RESPONSE = "OK"
AT+FCLASS=1	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FCLASS=2	RESULT = "OK"	RESPONSE = "OK"
AT+FCLASS?	RESULT = "OK"	RESPONSE = "2"
AT+FJUNK=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FJUNK?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FAA=?	RESULT = "OK"	RESPONSE = "060"
AT+FAA?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FAXERR=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FAXERR?	RESULT = "OK"	RESPONSE = "OK"
AT+FBADLIN=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FBADLIN?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FBADMUL=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FBADMUL?	RESULT = "OK"	RESPONSE = "OK"
AT+FBOR=?	RESULT = "OK"	RESPONSE = "060"
AT+FBOR?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FBUF=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FBUF?	RESULT = "OK"	RESPONSE = "OK"
AT+FBUG=?	RESULT = "OK"	RESPONSE = "060"
AT+FBUG?	RESULT = "OK"	RESPONSE = "0"
AT+FCIG=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FCIG?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FCQ=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FCQ?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FCR=?	RESULT = "OK"	RESPONSE = "060"
AT+FCR?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FTBC=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FTBC?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FDCC=?	RESULT = "OK"	RESPONSE = "(0-1),(0-5),(0-3),(0-2),(0-2),(0),(0),(0-7)"
AT+FDCC?	RESULT = "OK"	RESPONSE = ",,0,2,0,0,0,0"
AT+FDCS=?	RESULT = "OK"	RESPONSE = "(0-1),(0-5),(0-3),(0-2),(0-2),(0),(0),(0-7)"
AT+FDCS?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FDIS=?	RESULT = "OK"	RESPONSE = "(0-1),(0-5),(0-3),(0-2),(0-2),(0),(0),(0-7)"
AT+FDIS?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FDT=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FDT?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FECM=?	RESULT = "OK"	RESPONSE = "060"
AT+FECM?	RESULT = "OK"	RESPONSE = "OK"
AT+FET=?	RESULT = "OK"	RESPONSE = "060"
AT+FET?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FLID=?	RESULT = "OK"	RESPONSE = ""
AT+FLID?	RESULT = "OK"	RESPONSE = "E.C.  Version : 7.1"
AT+FLNFC=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FLNFC?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FLPL=?	RESULT = "OK"	RESPONSE = "060"
AT+FLPL?	RESULT = "OK"	RESPONSE = "0"
AT+FMDL?	RESULT = "OK"	RESPONSE = "ROCKWELL 144DP"
AT+FMFR?	RESULT = "OK"	RESPONSE = "EXAR"
AT+FMINSP=?	RESULT = "OK"	RESPONSE = "060"
AT+FMINSP?	RESULT = "OK"	RESPONSE = "OK"
AT+FPHCTO=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FPHCTO?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FPTS=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FPTS?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FRBC=?	RESULT = "OK"	RESPONSE = "060"
AT+FRBC?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FREL=?	RESULT = "OK"	RESPONSE = "EXAR"
AT+FREL?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FREV?	RESULT = "OK"	RESPONSE = "E.C.  Version : 7.1"
AT+FSPL=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FSPL?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FTBC=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FTBC?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FVRFC=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FVRFC?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FWDFC=?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FWDFC?	RESULT = "ERROR"	RESPONSE = "ERROR"
AT+FK=?	RESULT = "OK"	RESPONSE = "060"


the faxaddmodem dives me the config.ttyS0

# $Id: exar,v 1.1.1.1 1998/10/12 20:47:47 root Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Exar-manufactured Class 2 modem.
#	Yocom 1414E		firmware E.C.  Version : 7.1
#
# This configuration file sets up the modem to run at 19.2 for
# sending and for receiving.  XON/XOFF flow control is used on
# the tty port.
#
#
CountryCode:		49
AreaCode:		2224
FAXNumber:		##########   for security fx-nr-hidden
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	0
SpeakerVolume:		quiet
GettyArgs:		""
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		19200		# fax send&recv is locked at 19.2
ModemFlowControl:	xonxoff		# default
#
ModemSoftFlowCmd:	AT&S1\G0\Q4\X1	# software flow control
ModemSetupDTRCmd:	AT&D2		# DTR off causes modem to reset
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
ModemSetupAACmd:	AT+FAA=1	# enable in current class
#
ModemSendFillOrder:	LSB2MSB		# as expected
ModemRecvFillOrder:	MSB2LSB		# opposite of what makes sense
#
ModemDialCmd:		ATX3DT%s@		# T for tone dialing, @ for silence
#
ModemWaitForConnect:	yes		# wait for CONNECT on answer
#
Class2RecvDataTrigger:	"\022"		# DC2
Class2DDISCmd:		AT+FDIS		# set parameter before dialing

As to this point it seems to be succsessfull.
But when i try to send a fax, the other fax machine gets a call and hook up, the
modem trys to get a connection, but after a while it stops and no transmitting
starts. The log file shows :

Jun 13 18:06:02.08: [ 7741]: SESSION BEGIN 00000060 49222415
Jun 13 18:06:02.08: [ 7741]: HylaFAX (tm) Version 4.1
Jun 13 18:06:02.08: [ 7741]: SEND FAX: JOB 22 DEST ######## COMMID 00000060   
#########= Destination 
Jun 13 18:06:02.08: [ 7741]: DEVICE '/dev/ttyS0'
Jun 13 18:06:02.08: [ 7741]: DELAY 75 ms
Jun 13 18:06:02.16: [ 7741]: DELAY 2600 ms
Jun 13 18:06:04.76: [ 7741]: <-- [4:ATZ\r]
Jun 13 18:06:05.36: [ 7741]: --> [2:OK]
Jun 13 18:06:05.36: [ 7741]: <-- [5:ATE0\r]
Jun 13 18:06:05.59: [ 7741]: --> [4:ATE0]
Jun 13 18:06:05.59: [ 7741]: --> [2:OK]
Jun 13 18:06:05.59: [ 7741]: <-- [5:ATV1\r]
Jun 13 18:06:05.82: [ 7741]: --> [2:OK]
Jun 13 18:06:05.82: [ 7741]: <-- [5:ATQ0\r]
Jun 13 18:06:06.05: [ 7741]: --> [2:OK]
Jun 13 18:06:06.05: [ 7741]: <-- [7:ATS0=0\r]
Jun 13 18:06:06.28: [ 7741]: --> [2:OK]
Jun 13 18:06:06.28: [ 7741]: <-- [7:ATS8=2\r]
Jun 13 18:06:06.51: [ 7741]: --> [2:OK]
Jun 13 18:06:06.51: [ 7741]: <-- [8:ATS7=60\r]
Jun 13 18:06:06.75: [ 7741]: --> [2:OK]
Jun 13 18:06:06.75: [ 7741]: <-- [15:AT&S1\G0\Q4\X1\r]
Jun 13 18:06:06.98: [ 7741]: --> [2:OK]
Jun 13 18:06:06.98: [ 7741]: <-- [6:AT&D2\r]
Jun 13 18:06:07.21: [ 7741]: --> [2:OK]
Jun 13 18:06:07.21: [ 7741]: <-- [6:AT&C1\r]
Jun 13 18:06:07.44: [ 7741]: --> [2:OK]
Jun 13 18:06:07.44: [ 7741]: <-- [12:AT+FCLASS=2\r]
Jun 13 18:06:07.68: [ 7741]: --> [2:OK]
Jun 13 18:06:07.68: [ 7741]: <-- [10:AT+FTBC=0\r]
Jun 13 18:06:07.92: [ 7741]: --> [5:ERROR]
Jun 13 18:06:07.92: [ 7741]: MODEM Command error
Jun 13 18:06:07.92: [ 7741]: <-- [10:AT+FBOR=0\r]
Jun 13 18:06:08.15: [ 7741]: --> [2:OK]
Jun 13 18:06:08.15: [ 7741]: <-- [13:AT+FPHCTO=30\r]
Jun 13 18:06:08.39: [ 7741]: --> [5:ERROR]
Jun 13 18:06:08.39: [ 7741]: MODEM Command error
Jun 13 18:06:08.39: [ 7741]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Jun 13 18:06:08.63: [ 7741]: --> [2:OK]
Jun 13 18:06:08.63: [ 7741]: <-- [7:ATL0M1\r]
Jun 13 18:06:08.86: [ 7741]: --> [2:OK]
Jun 13 18:06:08.86: [ 7741]: <-- [12:AT+FCLASS=2\r]
Jun 13 18:06:09.20: [ 7741]: --> [2:OK]
Jun 13 18:06:09.20: [ 7741]: <-- [10:AT+FTBC=0\r]
Jun 13 18:06:09.53: [ 7741]: --> [5:ERROR]
Jun 13 18:06:09.53: [ 7741]: MODEM Command error
Jun 13 18:06:09.53: [ 7741]: <-- [10:AT+FBOR=0\r]
Jun 13 18:06:09.86: [ 7741]: --> [2:OK]
Jun 13 18:06:09.86: [ 7741]: <-- [13:AT+FPHCTO=30\r]
Jun 13 18:06:10.20: [ 7741]: --> [5:ERROR]
Jun 13 18:06:10.20: [ 7741]: MODEM Command error
Jun 13 18:06:10.20: [ 7741]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Jun 13 18:06:10.54: [ 7741]: --> [2:OK]
Jun 13 18:06:10.54: [ 7741]: <-- [24:AT+FLID="+4922#############"\r]    #### for
security fax-nr- hidden
Jun 13 18:06:10.88: [ 7741]: --> [2:OK]
Jun 13 18:06:10.88: [ 7741]: <-- [24:AT+FDIS=0,5,0,2,0,0,0,0\r]
Jun 13 18:06:11.22: [ 7741]: --> [2:OK]
Jun 13 18:06:11.22: [ 7741]: DIAL 15
Jun 13 18:06:11.22: [ 7741]: <-- [10:ATX3DT##################@\r]
Jun 13 18:07:14.77: [ 7741]: --> [9:NO ANSWER]
Jun 13 18:07:14.77: [ 7741]: SEND FAILED: JOB 22 DEST ################# ERR No
answer from remote
Jun 13 18:07:14.77: [ 7741]: <-- [5:ATH0\r]
Jun 13 18:07:19.77: [ 7741]: MODEM <Timeout>
Jun 13 18:07:19.77: [ 7741]: SESSION END





Any idea to bring the modem to work ?


thank you very much
Heribert 

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*