Re: [hylafax-users] GVC Fax 14400 V.42bis/MNP5 Modem Problem with Hylafax

["Michael J. Pedersen" <pedermj@xxxxxxxxxxx>]

On Sun, Jun 13, 2004 at 06:29:06PM -0700, Lee Howard wrote:
> Here are the relevant parts of the post:
> ATI0	RESULT = "OK"	RESPONSE = "242"
> ATI1	RESULT = "OK"	RESPONSE = "175"
> ATI2	RESULT = "OK"	RESPONSE = "OK"
> ATI3	RESULT = "OK"	RESPONSE = "E.C.  Version : 7.1"

Thank you. I can pretty safely say that that modem is a GVC 14.4
modem.

I'm kind of suspicious of the output, though. For comparison, here's the
output from a GVC 28.8 ATI command set.

ATI0
288

OK

ATI1
173

F1128V/R6  V6.18.13

OK

ATI2
OK
ATI3
E.C. Version: T
ATI4

F1128V/R6  V6.18.13

MODEM CHIP: ROCKWELL RC288DPi

FAX CLASS 1 AND FAX CLASS 2

OK
AT+FCLASS=?
0,1,2

OK

Notice the carriage returns in responses. Dunno if that will matter to
HylaFAX or not. However, it is most definitely class 1 and 2 capable. In
fact all GVC modems that were class 2 capable were class 1 capable.

I'm attaching my config.ttyS1 in hope that it
will help.

-----config.ttyS1

# $Id: gvc-288-2,v 1.3 2002/04/07 20:29:26 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a GVC MAXTech 288 RC288DPi-based Class 2 modem.
# Tested with firmware rev KA1131-00.
#
# NB: DCD is toggled at page end during transmits; this can
#     cause problems on systems where it's not possible to
#     set CLOCAL and also enable RTS/CTS flow control.
#
#
CountryCode:		1
AreaCode:		908
FAXNumber:		1-908-435-3711
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		0x08501
SessionTracing:		0x08501
RecvFileMode:		0640
LogFileMode:		0640
DeviceMode:		0660
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-r -b %l"
LocalIdentifier:	"Michael Pedersen"
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 1 interface
ModemRate:		19200		# locked for fax sending&receiving
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT\Q0		# disable flow control cmd
ModemSoftFlowCmd:	AT\Q1		# software flow control cmd
ModemHardFlowCmd:	AT\Q3		# hardware flow control cmd
ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
ModemSetupAACmd:	AT+FAA=1	# enable adaptive-answer in Class 2
#
ModemRecvFillOrder:	MSB2LSB		# bit order of received facsimile
ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
ModemDialCmd:		ATDT%s		# T for tone dialing
#
# Chip locks the line rate and switches to xon/xoff flow
# control when receiving facsimile--we must follow suit.
#
ModemAnswerFaxBeginCmd:	"<19200><xon>"	# lock line rate & switch flow control
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv
#
# These are known to not be implemented on the GVC with the above
# firmware rev.  Sending them to the modem does not harm anything,
# but generates an ERROR result that can generate questions from the
# naive--so we disable them here.
#
Class2TBCCmd:		none		# setup stream mode
Class2PHCTOCmd:		none		# set phase C timeout parameter

--end config.ttyS1
-- 
Michael J. Pedersen
My IM IDs: Jabber/pedersen@xxxxxxxxxxxxxx, ICQ/103345809, AIM/pedermj022171
           Yahoo/pedermj2002, MSN/pedermj022171@xxxxxxxxxxx
My GnuPG KeyID: 6CB0A96C       My Public Key Available At: www.keyserver.net
My GnuPG Key Fingerprint: E8F0 920F EB2F 7FDE DF4E  23CC 2CEB 8E6F 6CB0 A96C

Attachment: pgp00002.pgp
Description: PGP signature