Re: [hylafax-users] HylaFAX not receiving faxes.

["Ramon F. McDougall" <rfm@xxxxxxxxxxxxxxxxxx>]

Ramon F. McDougall wrote:
> David Forrest wrote:
> > On Tue, 25 Nov 2008, Ramon F. McDougall wrote:
> >
> > > Aidan Van Dyk wrote:
> > > > * Ramon F. McDougall <rfm@xxxxxxxxxxxxxxxxxx> [081125 21:26]:
> > > >
> > > > > Hi,
> > > > >
> > > > > The reason I included that one is because my system did not create 
> > > > > ttyS1. I thought that all those files are related somehow. I 
> > > > > figured that if you have your ttyS1 for your serial device that it 
> > > > > would write a corresponding file to event file. That makes it 
> > > > > interesting even though the distributions are different the files 
> > > > > are similar. I will edit mine tty1 and try to start that warlock 
> > > > > faxgetty deamon.
> > > >
> > > >
> > > > Look at /etc/default/hylafax, where you "configure" HylaFAX service
> > > > start/stop/options in debian (and thus ubuntu). You tell it in 
> > > > there whether
> > > > you're runing faxgettys already from init (well, I guess in ubuntu 
> > > > you'll have
> > > > to figure it out in upstart/event.d), or if you want to make the 
> > > > rc.d script
> > > > start them for you.
> > > >
> > > > You have to make sure your config matches your "init".
> > > >
> > > > a.
> > > I looked at /etc/default/ but there is not hylafax.
> > >
> > > [root@Hermes /]# cd /etc/default
> > > [root@Hermes default]# ls
> > > nss useradd
> > >
> > >
> > > Thanks,
> > >
> > > Ramon
> >
> > Ramon, I've been off the list for a while and out of town so I've 
> > missed some of your prior notes.
> >
> > I am running Fedora 9 and had a dickens of a time getting it all set 
> > up the first time so I feel for you considering the frustration I 
> > had. I remember you said you were running F9. If so try the following.
> >
> > First: run the command chkconfig to see what gets started in each 
> > runlevel. hylafax should run ("on") in runlevels 2,3,4, and 5, and be 
> > "off" in 0,1, and 6. faxsetup should have created this setup.
> >
> > Second: run the command dmesg | grep tty to see what tty's have been 
> > found. One of them should be your modem.
> >
> > Third: check to see if there is a config file for your modem in 
> > /var/spool/hylafax/etc. File should be named config.ttyXXX (replace 
> > XXX with whatever you found in step 2) If it does not exist, rerun 
> > faxaddmodem using the ttyXXX you found in step 2.
> >
> > Fourth: Check to see if faxgetty is running. ps axl |grep faxgetty 
> > should show /usr/local/sbin/faxgetty ttyXXX if it is. If not, just 
> > start it as root as faxgetty ttyXXX. It is better to have it always 
> > running as it forks for each call; mine seems to be the same pid for 
> > weeks on end and runs as user uucp. I do use the F9 
> > /etc/event.d/ttyXXX script, though, which should respawn it if it 
> > gets killed for any reason. See the man init and man telinit pages. 
> > Thsi script was installed by the make install command as I compiled 
> > hylafax from source. I do not know how the rpm binaries do it but I 
> > assume they "just do it".
> >
> > There is a short page here: 
> > http://maplepark.com/~drf/consults/FaxServer.php
> > about my system and config files.
> >
> >
> >
> > David Forrest e-mail drf@xxxxxxxxxxxxx
> > Maple Park Development Corporation http://www.maplepark.com
> > St. Louis, Missouri
> Well I'm glad you are back in town. :-) Welcome back.
> First:
> [root@Hermes /]# chkconfig
>
> hylafax 0:off 1:off 2:off 3:on 4:on 5:on 6:offo I have to assume it 
> has been running all along.
>
>
> Well 2 is off. I guess I need to edit the inittab an include 2.
>
> Second:
> [root@Hermes /]# dmesg | grep tty
> console [tty0] enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 0000:00:08.0: ttyS1 at I/O 0xe400 (irq = 17) is a 16550A
>
> ttyS1 on irq 17 is verified
>
> Third:
>
> root@Hermes etc]# ls
> config dialrules FaxDispatch setup.cache
> config.sav dialrules.europe hosts.hfaxd setup.modem
> config.ttyS1 dialrules.sf-ba lastrun templates
> cover.templ dpsprinter.ps lutRS18.pcf xferfaxlog
> [root@Hermes etc]#
>
> There is a config.ttyS1
>
> Fourth:
>
> [root@Hermes /]# ps axl |grep faxgetty
> 0 0 4714 3851 20 0 5036 688 pipe_w S+ pts/3 0:00 grep faxgetty
>
> Well I was running ps -ef and could never see. I'll attempt to start 
> it again. Attempted to start faxgetty which is
> in the /usr/sbin but I get a blinking cursor only, how long does it 
> blink for before it starts?
>
> I was under the impression that the RPMs would be easier. I was 
> attempting to do a source install and that did not
> work for me so I tried the RPM.
>
> Thanks,
>
> Ramon
>
>
>
>
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>  To subscribe/unsubscribe, click 
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
> /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
I just went back and did a:

[root@Hermes /]# ps axl |grep faxgetty
4    10  4724  3851  20   0   8024  1444 signal T    pts/3      0:00 
faxgetty ttyS1
4    10  4732  3851  20   0   8024  1440 select S+   pts/3      0:00 
faxgetty ttyS1

Question: Is it normal that when you run the command that you get 
blinking cursor after typing? I thought it will get you back at the 
prompt #.

/usr/sbin/fagetty ttyS1

Well this is some progress now. I will need to test the fax see if it 
will answer. If you don't mind please try fax me at 305 373 8108.


Thank you and Kind Regards,

Ramon


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*