Re: [hylafax-users] HDLC Frame too short...

[Lee Howard <lee.howard@xxxxxxxxxxxx>]

Martin Hucht wrote:
> I was asked by my Boss to evaluate Hylafax for my company, before purchasing
> an 3500,- Euro Appliance. I have to say that nearly everthing worked out of
> the box, but sending a fax :/. I set up Debian and installed Hylafax 4.4.3.
> I'm using a single Modem (1456VQE Topic Chipset). For cabeling reasons I'm
> using a NPort 5610 RS232-Device Server.
> Everytime I send a Fax I get this:
>
> Nov 10 17:28:06.70: [ 2571]: SESSION BEGIN 000000165 492504273
> Nov 10 17:28:06.70: [ 2571]: HylaFAX (tm) Version 4.4.3
> Nov 10 17:28:06.70: [ 2571]: SEND FAX: JOB 36 DEST 273 COMMID 000000165
> DEVICE '/dev/ttyp0' FROM 'faxuser <faxuser@xxxxxxxxxxxxxx>' USER faxuser
> Nov 10 17:28:06.70: [ 2571]: STATE CHANGE: RUNNING -> SENDING
> Nov 10 17:28:06.70: [ 2571]: <-- [12:AT+FCLASS=1\r]
> Nov 10 17:28:06.82: [ 2571]: --> [2:OK]
> Nov 10 17:28:06.82: [ 2571]: MODEM set XON/XOFF/FLUSH: input ignored, output
> disabled
> Nov 10 17:28:06.82: [ 2571]: DIAL 273
> Nov 10 17:28:06.82: [ 2571]: <-- [8:ATDT273\r]
> Nov 10 17:28:20.98: [ 2571]: --> [7:CONNECT]
> Nov 10 17:28:23.54: [ 2571]: --> [20:20 00 00 19 35 C0 A0 DF A5 FD D8 EF C0
> B0 A8 BF 01 0F 6E 65]
> Nov 10 17:28:23.54: [ 2571]: --> [20:73 65 77 74 65 69 4D 20 6F 6B 6B 61 54
> 04 01 07 07 03 0D 01]
> Nov 10 17:28:23.54: [ 2571]: --> [20:01 08 0F F0 02 05 02 19 00 06 01 04 07
> 01 01 09 01 07 94 1F]
> Nov 10 17:28:23.54: [ 2571]: --> [2:10 03]
> Nov 10 17:28:23.54: [ 2571]: --> [2:OK]
> Nov 10 17:28:23.54: [ 2571]: HDLC frame too short (0 bytes)
> Nov 10 17:28:23.54: [ 2571]: <-- [10:AT+FRS=21\r]
> Nov 10 17:28:23.56: [ 2571]: --> [2:OK]
> Nov 10 17:28:23.56: [ 2571]: <-- [9:AT+FTH=3\r]
> Nov 10 17:28:23.62: [ 2571]: --> [7:CONNECT]
> Nov 10 17:28:23.62: [ 2571]: <-- HDLC<3:FF C8 D8>
> Nov 10 17:28:23.62: [ 2571]: <-- data [3]
> Nov 10 17:28:23.62: [ 2571]: <-- data [2]
> Nov 10 17:28:23.65: [ 2571]: --> [7:CONNECT]
> Nov 10 17:28:31.11: [ 2571]: --> [0:]
> Nov 10 17:28:31.11: [ 2571]: MODEM <Empty line>
> Nov 10 17:28:31.11: [ 2571]: MODEM TIMEOUT: sending HDLC frame
> Nov 10 17:28:31.11: [ 2571]: <-- [9:AT+FRS=7\r]
> Nov 10 17:28:41.42: [ 2571]: --> [10:NO CARRIER]
> Nov 10 17:28:41.42: [ 2571]: MODEM No carrier
> Nov 10 17:28:41.42: [ 2571]: Failure to receive silence (synchronization
> failure).
> Nov 10 17:28:41.42: [ 2571]: <-- [9:AT+FRH=3\r]
> Nov 10 17:28:41.54: [ 2571]: --> [2:OK]
> Nov 10 17:28:41.54: [ 2571]: <-- [9:AT+FRS=7\r]
> Nov 10 17:28:41.66: [ 2571]: --> [2:OK]
>
> ...retry,retry....
>   

You say "retry,retry", but I am not certain that it means the same as 
what is given.

If the logging you provides is an accurate description of the entirety 
of what occurs later and in subsequent calls, then I'd say that the 
modem is unusable for fax.

Thanks,

Lee.


--
*Lee Howard*
*Mainpine, Inc. Software Development Lead*
Tel: +1 866 363 6680 ext 805 | Fax: +1 360 462 8160
lee.howard@xxxxxxxxxxxx | www.mainpine.com


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*