Re: [hylafax-users] cannot send with USR Sportster

[Nerijus Baliunas <nerijus@xxxxxxxxxxxxxxxxxxxxx>]

On Sun, 26 Oct 2008 19:58:27 -0700 Lee Howard <faxguy@xxxxxxxxxxxxxxxx> wrote:

> > Filename                 Size Type
> > docq/doc4.ps.4              0
> >
> > So I was able to see that size is 0. Of course, I should have noticed it earlier...
> 
> Did HylaFAX+ even attempt the fax (place a call) in the first place?  It 
> shouldn't have.

Yes. I've just tried - docq/doc5.ps.5 size is 0, sender log:

SESSION BEGIN 000000006 XXXXXXX
HylaFAX (tm) Version 5.2.7
SEND FAX: JOB 5 DEST xxxxxxx COMMID 000000006 DEVICE '/dev/ttyS0' FROM 'administrator <postmaster@ek
STATE CHANGE: RUNNING -> SENDING
<-- [12:AT+FCLASS=1\r]
--> [2:OK]
MODEM set XON/XOFF/FLUSH: input ignored, output disabled
DIAL 9,xxxxxxx
<-- [14:ATDT9,xxxxxxx\r]
--> [7:CONNECT]
--> HDLC<34:FF C0 04 AD 00 55 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 4C 74 AC 95 75>
--> [2:OK]
REMOTE NSF "B5 00 AA 48 79 6C 61 46 41 58 20 28 74 6D 29 20 56 65 72 73 69 6F 6E 20 34 2E 32 2E 35"
NSF remote fax equipment: HylaFAX
NSF remote station ID: "HylaFAX (tm) Version 4.2.5"
<-- [9:AT+FRH=3\r]
--> [7:CONNECT]
--> HDLC<25:FF C0 02 CE 86 D6 CE 86 2A 04 CE 96 CE 86 96 36 86 5A 04 04 04 04 04 57 DD>
--> [2:OK]
REMOTE CSI "XXX YYY"
<-- [9:AT+FRH=3\r]
--> [7:CONNECT]
--> HDLC<15:FF C8 01 00 77 5F 23 01 FB C1 01 01 18 0C 8E>
--> [2:OK]
REMOTE best rate 14400 bit/s
REMOTE max A3 page width (303 mm)
REMOTE max unlimited page length
REMOTE best vres R16 x 15.4 line/mm
REMOTE format support: MH, MR, MMR
REMOTE supports T.30 Annex A, 256-byte ECM
REMOTE best 0 ms/scanline
USE 14400 bit/s
USE error correction mode
DELAY 70 ms
<-- [9:AT+FTH=3\r]
--> [7:CONNECT]
<-- HDLC<3:FF C8 DF>
<-- data [3]
<-- data [2]
--> [2:OK]
MODEM input buffering enabled
<-- [5:ATH0\r]
--> [2:OK]
MODEM set DTR OFF
STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
SESSION END

Receiver log:

SESSION BEGIN 000002411 XXXXXXX
HylaFAX (tm) Version 4.2.5
<-- [13:AT+FCLASS=1A\r]
--> [7:CONNECT]
ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
RECV FAX: begin
<-- data [32]
<-- data [2]
--> [7:CONNECT]
<-- data [23]
<-- data [2]
--> [7:CONNECT]
<-- data [13]
<-- data [2]
--> [2:OK]
<-- [9:AT+FRH=3\r]
--> [7:CONNECT]
--> [2:OK]
RECV FAX: RSPREC error/got DCN
RECV FAX: end
SESSION END


Regards,
Nerijus


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*