[hylafax-users] Since two days I cannot send faxes

[hychris@xxxxxxxxxxx]

Hi,

Since two days I cannot send faxes because of the error:

"Failure to train remote modem at 2400 bps or minimum speed"

Always I try I got this message.
From other servers with the same configuration I can send the same fax to
the same numbers without problems. The receiver-number is also a server
with ISDN in Germany, also working since years.

Here is the logfile: (I have marked the difference to the log-file of
another server dialed the same number.)

Dec 04 14:01:58.90: [13430]: SESSION BEGIN 000000102 49721509666000
Dec 04 14:01:58.90: [13430]: HylaFAX (tm) Version 4.4.1
Dec 04 14:01:58.90: [13430]: SEND FAX: JOB 79 DEST +49721509666000 COMMID
000000102 DEVICE '/dev/ttya09' FROM 'support <.............>' USER root
Dec 04 14:01:58.90: [13430]: <-- [12:AT+FCLASS=1\r]
Dec 04 14:01:58.92: [13430]: --> [2:OK]
Dec 04 14:01:58.95: [13430]: DIAL 01149721509666000
Dec 04 14:01:58.95: [13430]: <-- [22:ATDT01149721509666000\r]
Dec 04 14:02:25.41: [13430]: --> [7:CONNECT]
Dec 04 14:02:26.47: [13430]: --> [2:OK]
Dec 04 14:02:26.47: [13430]: REMOTE best rate 9600 bit/s
Dec 04 14:02:26.47: [13430]: REMOTE max A4 page width (215 mm)
Dec 04 14:02:26.47: [13430]: REMOTE max unlimited page length
Dec 04 14:02:26.47: [13430]: REMOTE best vres 7.7 line/mm
Dec 04 14:02:26.47: [13430]: REMOTE format support: MH, MR, MMR
Dec 04 14:02:26.47: [13430]: REMOTE supports T.30 Annex A, 256-byte ECM
Dec 04 14:02:26.47: [13430]: REMOTE best 0 ms/scanline
Dec 04 14:02:26.47: [13430]: USE 9600 bit/s
Dec 04 14:02:26.47: [13430]: USE error correction mode
Dec 04 14:02:26.47: [13430]: SEND file "docq/doc82.ps;c1"
Dec 04 14:02:26.47: [13430]: USE A4 page width (215 mm)
Dec 04 14:02:26.47: [13430]: USE unlimited page length
Dec 04 14:02:26.47: [13430]: USE 7.7 line/mm
Dec 04 14:02:26.47: [13430]: USE 2-D MMR
Dec 04 14:02:26.47: [13430]: USE 0 ms/scanline
Dec 04 14:02:26.47: [13430]: SEND training at v.29 9600 bit/s
Dec 04 14:02:26.47: [13430]: <-- [9:AT+FRS=7\r]
Dec 04 14:02:26.59: [13430]: --> [2:OK]
Dec 04 14:02:26.59: [13430]: <-- [9:AT+FTH=3\r]
Dec 04 14:02:26.65: [13430]: --> [7:CONNECT]
Dec 04 14:02:26.65: [13430]: <-- data [23]
Dec 04 14:02:26.65: [13430]: <-- data [2]
Dec 04 14:02:28.43: [13430]: --> [7:CONNECT]
Dec 04 14:02:28.43: [13430]: <-- data [7]
Dec 04 14:02:28.43: [13430]: <-- data [2]
Dec 04 14:02:28.87: [13430]: --> [2:OK]
Dec 04 14:02:28.87: [13430]: <-- [9:AT+FTS=7\r]
Dec 04 14:02:28.97: [13430]: --> [2:OK]
Dec 04 14:02:28.97: [13430]: <-- [10:AT+FTM=96\r]
Dec 04 14:02:29.03: [13430]: --> [7:CONNECT]
Dec 04 14:02:29.03: [13430]: <-- data [1024]
Dec 04 14:02:29.03: [13430]: <-- data [776]
Dec 04 14:02:29.03: [13430]: <-- data [2]
Dec 04 14:02:30.97: [13430]: --> [2:OK]
Dec 04 14:02:30.97: [13430]: <-- [9:AT+FRH=3\r]
Dec 04 14:02:34.07: [13430]: --> [0:]             <<<<<<<<< Problem???
Dec 04 14:02:34.07: [13430]: MODEM <Empty line>
Dec 04 14:02:34.07: [13430]: <-- data [1]
Dec 04 14:02:34.13: [13430]: --> [2:OK]
Dec 04 14:02:34.13: [13430]: <-- [9:AT+FRS=7\r]
Dec 04 14:02:34.27: [13430]: --> [2:OK]
Dec 04 14:02:34.27: [13430]: SEND training at v.29 7200 bit/s
Dec 04 14:02:34.27: [13430]: <-- [9:AT+FTH=3\r]
Dec 04 14:02:34.33: [13430]: --> [7:CONNECT]
Dec 04 14:02:34.33: [13430]: <-- data [23]
Dec 04 14:02:34.33: [13430]: <-- data [2]
Dec 04 14:02:36.11: [13430]: --> [7:CONNECT]
Dec 04 14:02:36.11: [13430]: <-- data [7]
Dec 04 14:02:36.11: [13430]: <-- data [2]
Dec 04 14:02:36.55: [13430]: --> [2:OK]
Dec 04 14:02:36.55: [13430]: <-- [9:AT+FTS=7\r]
Dec 04 14:02:36.65: [13430]: --> [2:OK]
Dec 04 14:02:36.65: [13430]: <-- [10:AT+FTM=72\r]
Dec 04 14:02:36.71: [13430]: --> [7:CONNECT]
Dec 04 14:02:36.71: [13430]: <-- data [1024]
Dec 04 14:02:36.71: [13430]: <-- data [326]
Dec 04 14:02:36.71: [13430]: <-- data [2]
Dec 04 14:02:38.65: [13430]: --> [2:OK]
Dec 04 14:02:38.65: [13430]: <-- [9:AT+FRH=3\r]
Dec 04 14:02:41.75: [13430]: --> [0:]
Dec 04 14:02:41.75: [13430]: MODEM <Empty line>
Dec 04 14:02:41.75: [13430]: <-- data [1]
Dec 04 14:02:41.81: [13430]: --> [2:OK]
Dec 04 14:02:41.81: [13430]: <-- [9:AT+FRS=7\r]
Dec 04 14:02:41.93: [13430]: --> [2:OK]
Dec 04 14:02:41.93: [13430]: TRAINING failed
Dec 04 14:02:41.93: [13430]: <-- [9:AT+FTH=3\r]
Dec 04 14:02:41.99: [13430]: --> [7:CONNECT]
Dec 04 14:02:41.99: [13430]: <-- data [3]
Dec 04 14:02:41.99: [13430]: <-- data [2]
Dec 04 14:02:43.29: [13430]: --> [2:OK]
Dec 04 14:02:44.29: [13430]: <-- [5:ATH0\r]
Dec 04 14:02:45.21: [13430]: --> [2:OK]
Dec 04 14:02:45.21: [13430]: SESSION END


I have no idea what happens, especially because of the server has worked
fine all the time till 2days before.

What can I do to fix this problem?

best regards
Christian


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*