 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Problem to recived Faxs
- To: hylafax-users <hylafax-users@xxxxxxxxxxx>
- Subject: [hylafax-users] Problem to recived Faxs
- From: pigna <lucap78@xxxxxxxxxxxx>
- Date: Mon, 10 Sep 2007 16:03:22 +0200
Hi All.
I have installed Hylafax+ 5.1.7 on OpenSuse 10.2.
Hylafax use modem US Robotics 56K FAX EXT Rev. 11.16.63, Product ID: 0056300.
I have a problem on to recive some fax, Hylafax return me error: session with terminated abnormally: T.30 T2 timeout, expected page not received {E111}.
This is configuration file of modem:
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and RTS/CTS flow control.
#
ModemType: Class1 # use class 1 interface
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: rtscts # hardware flow control
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
ModemResultCodesCmd: ATQ0X3 # enable result codes
ModemMfrQueryCmd: !USR
ModemModelQueryCmd: ATI3
ModemRevQueryCmd: ATI7 # XXX, returns a multi-line result
Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control
Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow control
Class1SFLOCmd: "" # modem does this automatically
Class1SwitchingCmd: <delay:7> # Test 2
ModemSetupAACmd: AT+FCLASS=0&H1&I0&R2 # leave modem in class 0
ModemAnswerCmd: AT+FCLASS=1&H1&I0&R2A # force RTS/CTS after change
Class2NRCmd: AT+FNR=1,1,1,0
#Test
#Class1RMQueryCmd: "!3,24"
And this is one log:
Sep 10 15:46:15.84: [ 3602]: SESSION BEGIN 000136694 +39xxxxxxxx
Sep 10 15:46:15.84: [ 3602]: HylaFAX (tm) Version 5.1.7
Sep 10 15:46:15.84: [ 3602]: <-- [22:AT+FCLASS=1&H1&I0&R2A\r]
Sep 10 15:46:21.04: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:21.04: [ 3602]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyr00'
Sep 10 15:46:21.04: [ 3602]: RECV FAX: begin
Sep 10 15:46:21.05: [ 3602]: <-- data [32]
Sep 10 15:46:21.05: [ 3602]: <-- data [2]
Sep 10 15:46:21.20: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:21.20: [ 3602]: <-- data [23]
Sep 10 15:46:21.20: [ 3602]: <-- data [2]
Sep 10 15:46:21.92: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:21.92: [ 3602]: <-- data [13]
Sep 10 15:46:21.92: [ 3602]: <-- data [2]
Sep 10 15:46:24.19: [ 3602]: --> [2:OK]
Sep 10 15:46:24.19: [ 3602]: <-- [9:AT+FRH=3\r]
Sep 10 15:46:24.50: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:25.81: [ 3602]: --> [5:ERROR]
Sep 10 15:46:25.81: [ 3602]: MODEM Command error
Sep 10 15:46:25.81: [ 3602]: FCS error
Sep 10 15:46:25.81: [ 3602]: DELAY 70 ms
Sep 10 15:46:25.88: [ 3602]: <-- [9:AT+FTH=3\r]
Sep 10 15:46:26.07: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:26.07: [ 3602]: <-- data [3]
Sep 10 15:46:26.07: [ 3602]: <-- data [2]
Sep 10 15:46:27.25: [ 3602]: --> [2:OK]
Sep 10 15:46:27.25: [ 3602]: RECV send CRP (command repeat)
Sep 10 15:46:27.25: [ 3602]: <-- [9:AT+FRH=3\r]
Sep 10 15:46:27.89: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:34.06: [ 3602]: --> [5:ERROR]
Sep 10 15:46:34.06: [ 3602]: MODEM Command error
Sep 10 15:46:34.06: [ 3602]: FCS error
Sep 10 15:46:34.06: [ 3602]: DELAY 70 ms
Sep 10 15:46:34.14: [ 3602]: <-- [9:AT+FTH=3\r]
Sep 10 15:46:34.33: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:34.33: [ 3602]: <-- data [3]
Sep 10 15:46:34.33: [ 3602]: <-- data [2]
Sep 10 15:46:35.51: [ 3602]: --> [2:OK]
Sep 10 15:46:35.51: [ 3602]: RECV send CRP (command repeat)
Sep 10 15:46:35.51: [ 3602]: <-- [9:AT+FRH=3\r]
Sep 10 15:46:36.14: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:41.33: [ 3602]: --> [5:ERROR]
Sep 10 15:46:41.33: [ 3602]: MODEM Command error
Sep 10 15:46:41.33: [ 3602]: FCS error
Sep 10 15:46:41.33: [ 3602]: DELAY 70 ms
Sep 10 15:46:41.41: [ 3602]: <-- [9:AT+FTH=3\r]
Sep 10 15:46:41.61: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:41.61: [ 3602]: <-- data [3]
Sep 10 15:46:41.61: [ 3602]: <-- data [2]
Sep 10 15:46:42.78: [ 3602]: --> [2:OK]
Sep 10 15:46:42.78: [ 3602]: RECV send CRP (command repeat)
Sep 10 15:46:42.78: [ 3602]: <-- [9:AT+FRH=3\r]
Sep 10 15:46:43.50: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:45.13: [ 3602]: --> [2:OK]
Sep 10 15:46:45.13: [ 3602]: RECV recv TSI (sender id)
Sep 10 15:46:45.13: [ 3602]: REMOTE TSI ""
Sep 10 15:46:45.13: [ 3602]: <-- [9:AT+FRH=3\r]
Sep 10 15:46:45.15: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:45.48: [ 3602]: --> [2:OK]
Sep 10 15:46:45.48: [ 3602]: RECV recv DCS (command signal)
Sep 10 15:46:45.48: [ 3602]: REMOTE wants 14400 bit/s
Sep 10 15:46:45.48: [ 3602]: REMOTE wants A4 page width (215 mm)
Sep 10 15:46:45.48: [ 3602]: REMOTE wants unlimited page length
Sep 10 15:46:45.48: [ 3602]: REMOTE wants 3.85 line/mm
Sep 10 15:46:45.48: [ 3602]: REMOTE wants 1-D MH
Sep 10 15:46:45.48: [ 3602]: RECV training at v.17 14400 bit/s
Sep 10 15:46:45.48: [ 3602]: <-- [11:AT+FRM=145\r]
Sep 10 15:46:47.14: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:48.59: [ 3602]: RECV: TCF 2631 bytes, 2% non-zero, 2563 zero-run
Sep 10 15:46:48.60: [ 3602]: --> [10:NO CARRIER]
Sep 10 15:46:48.60: [ 3602]: DELAY 70 ms
Sep 10 15:46:48.67: [ 3602]: TRAINING succeeded
Sep 10 15:46:48.67: [ 3602]: <-- [9:AT+FTH=3\r]
Sep 10 15:46:48.87: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:48.87: [ 3602]: <-- data [3]
Sep 10 15:46:48.87: [ 3602]: <-- data [2]
Sep 10 15:46:50.05: [ 3602]: --> [2:OK]
Sep 10 15:46:50.05: [ 3602]: <-- [11:AT+FRM=146\r]
Sep 10 15:46:51.61: [ 3602]: --> [7:CONNECT]
Sep 10 15:46:51.62: [ 3602]: RECV: begin page
Sep 10 15:47:03.87: [ 3602]: RECV: 21842 bytes of data, 990 total lines
Sep 10 15:47:03.87: [ 3602]: RECV: end page
Sep 10 15:47:03.87: [ 3602]: --> [10:NO CARRIER]
Sep 10 15:47:03.87: [ 3602]: <-- [9:AT+FRH=3\r]
Sep 10 15:47:04.38: [ 3602]: --> [7:CONNECT]
Sep 10 15:47:05.11: [ 3602]: --> [2:OK]
Sep 10 15:47:05.11: [ 3602]: RECV recv MPS (more pages, same document)
Sep 10 15:47:05.11: [ 3602]: DELAY 70 ms
Sep 10 15:47:05.18: [ 3602]: RECV send MCF (message confirmation)
Sep 10 15:47:05.18: [ 3602]: <-- [9:AT+FTH=3\r]
Sep 10 15:47:05.48: [ 3602]: --> [7:CONNECT]
Sep 10 15:47:05.48: [ 3602]: RECV FAX (000136694): from , page 1 in 0:42, INF, 3.85 line/mm, 1-D MH, 14400 bit/s
Sep 10 15:47:05.48: [ 3602]: <-- data [3]
Sep 10 15:47:05.48: [ 3602]: <-- data [2]
Sep 10 15:47:06.65: [ 3602]: --> [2:OK]
Sep 10 15:47:06.65: [ 3602]: <-- [11:AT+FRM=146\r]
Sep 10 15:47:13.66: [ 3602]: <-- data [1]
Sep 10 15:47:13.77: [ 3602]: --> [2:OK]
Sep 10 15:47:13.77: [ 3602]: <-- [9:AT+FRH=3\r]
Sep 10 15:47:17.28: [ 3602]: --> [7:CONNECT]
Sep 10 15:47:27.29: [ 3602]: <-- data [1]
Sep 10 15:47:27.40: [ 3602]: --> [2:OK]
Sep 10 15:47:27.40: [ 3602]: <-- data [1]
Sep 10 15:47:27.61: [ 3602]: MODEM <Timeout>
Sep 10 15:47:27.61: [ 3602]: RECV FAX (000136694): recvq/fax000114206.tif from , subaddress <unspecified>, 1 pages in 1:06
Sep 10 15:47:27.61: [ 3602]: RECV FAX: T.30 T2 timeout, expected page not received {E111}
Sep 10 15:47:27.61: [ 3602]: <-- [9:AT+FTH=3\r]
Sep 10 15:47:27.75: [ 3602]: --> [7:CONNECT]
Sep 10 15:47:27.75: [ 3602]: <-- data [3]
Sep 10 15:47:27.75: [ 3602]: <-- data [2]
Sep 10 15:47:28.92: [ 3602]: --> [2:OK]
Sep 10 15:47:28.93: [ 3602]: RECV FAX (000136694): session with terminated abnormally: T.30 T2 timeout, expected page not received {E111}
Sep 10 15:47:28.93: [ 3602]: RECV FAX: bin/faxrcvd 'recvq/fax000114206.tif' 'ttyr00' '000136694' 'T.30 T2 timeout, expected page not received {E111}'
Sep 10 15:47:28.93: [ 3602]: RECV FAX: end
Sep 10 15:47:28.93: [ 3602]: SESSION END
Help me for resolv the problem please!!! :)
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Problem to recived Faxs
- From: Lee Howard
- Re: [hylafax-users] Problem to recived Faxs
- Prev by Date: Re: [hylafax-users] Faxgetty gets stuck after receiving a fax
- Next by Date: [hylafax-users] using faxsend/faxstat behind a nat firewall - REVISITED - how does the passive connection work?
- Previous by thread: Re: [hylafax-users] Faxgetty gets stuck after receiving a fax
- Next by thread: Re: [hylafax-users] Problem to recived Faxs
- Index(es):
Project hosted by iFAX Solutions