Re: [hylafax-users] COMREC invalid response received to PPS

["Marcello Golfieri" <golfieri@xxxxxxxxx>]

Hi there,

I am too using one instance of iaxmodem 0.2.1.  Stacking almost instantly 2 faxes by means of faxmail app I get "COMREC invalid command received" error when second fax is being transmitted on first dial.  Usually it gets done on second dial, sometimes even at third one.

Isn't it that hylafax with iaxmodem needs a pause between two sendings?  If this is the case, how can I instruct the sendq to put a wait between jobs?

I just attached my log for the faulty fax transmission.

Thanks all, keep up the good work!

apr 27 11:47:03.70: [  312]: SESSION BEGIN 000000238 390532499
apr 27 11:47:03.70: [  312]: HylaFAX (tm) Version 4.3.2
apr 27 11:47:03.70: [  312]: SEND FAX: JOB 104 DEST 499 COMMID 000000238 DEVICE '/dev/ttyIAX0' FROM 'open1 <
open1@xxxxxxxxxxxxxxxxx>' USER open1
apr 27 11:47:03.70: [  312]: STATE CHANGE: RUNNING -> SENDING
apr 27 11:47:03.70: [  312]: <-- [12:AT+FCLASS=1\r]
apr 27 11:47:
03.70: [  312]: --> [2:OK]
apr 27 11:47:03.70: [  312]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
apr 27 11:47:03.70: [  312]: DIAL 499
apr 27 11:47:03.70: [  312]: <-- [8:ATDT499\r]
apr 27 11:47:
07.52: [  312]: --> [7:CONNECT]
apr 27 11:47:08.66: [  312]: --> HDLC<5:FF C8 F4 CC 66>
apr 27 11:47:08.70: [  312]: --> [2:OK]
apr 27 11:47:08.70: [  312]: COMREC invalid command received/no DIS or DTC
apr 27 11:47:08.70: [  312]: SEND FAILED: JOB 104 DEST 499 ERR COMREC invalid command received/no DIS or DTC
apr 27 11:47:08.70: [  312]: <-- [9:AT+FTH=3\r]
apr 27 11:47:08.71: [  312]: --> [7:CONNECT]
apr 27 11:47:08.71: [  312]: <-- HDLC<3:FF C8 DF>
apr 27 11:47:08.71: [  312]: <-- data [3]
apr 27 11:47:08.71: [  312]: <-- data [2]
apr 27 11:47:09.79: [  312]: --> [2:OK]
apr 27 11:47:09.79
: [  312]: MODEM input buffering enabled
apr 27 11:47:09.79: [  312]: SEND FAILED: JOB 104 DEST 499 ERR COMREC invalid command received/no DIS or DTC; too many attempts to send
apr 27 11:47:09.79: [  312]: <-- [5:ATH0\r]
apr 27 11:47:09.90: [  312]: --> [2:OK]
apr 27 11:47:09.90: [  312]: MODEM set DTR OFF
apr 27 11:47:09.90: [  312]: MODEM set baud rate: 0 baud (flow control unchanged)
apr 27 11:47:09.90: [  312]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
apr 27 11:47:09.90: [  312]: SESSION END

-- 
Marcello Golfieri