[hylafax-users] Problems trying to fax from Eicon PRI to Eicon PRI

["Ulf Zimmermann" <ulf@xxxxxxxxxxxxxx>]

I currently have 3 servers. Two in Fremont, CA and one in Phoenix, AZ.
In Fremont one server has a Patton 2977 card with an older Hylafax
install and another server with an Eicon PRI card with Hylafax
Enterprise 2.4.7.

In Phoenix I had a Patton 2977 card and just swapped it with an Eicon
PRI and then upgraded the OS (RedHat EL4) and installed Hylafax 4.3.3.

When I try to fax from Eicon server in Fremont to the Eicon server in
Phoenix, I get on the Phoenix side just:

Apr 13 23:33:30.27: [ 5278]: SESSION BEGIN 000000011 16023241958
Apr 13 23:33:30.27: [ 5278]: HylaFAX (tm) Version 4.3.3
Apr 13 23:33:30.27: [ 5278]: CallID: "5107431400" "6023241958"
Apr 13 23:33:30.27: [ 5278]: <-- [11:ATS0=255;A\r]
Apr 13 23:33:37.56: [ 5278]: --> [8:+FHNG: 3]
Apr 13 23:33:37.56: [ 5278]: REMOTE HANGUP: No loop current (code 3)
Apr 13 23:33:37.56: [ 5278]: ANSWER: Ring detected without successful
handshake
Apr 13 23:33:37.56: [ 5278]: SESSION END

On the Fremont side I get the job rejected with "High resolution
document is not supported by client" and the log looks like:

Apr 13 23:47:07.57: [18477]: SESSION BEGIN 000000046 16023241958
Apr 13 23:47:07.57: [18477]: HylaFAX (tm) Enterprise Version 2.4.7
Apr 13 23:47:07.57: [18477]: SEND FAX: JOB 18 DEST 6023241958 COMMID
000000046 DEVICE '/dev/ttyds22' FROM 'Ulf Zimmermann
<ulf@xxxxxxxxxxxxxxxxxxxxxx>' USER ulf
Apr 13 23:47:07.57: [18477]: <-- [10:AT+FBOR=0\r]
Apr 13 23:47:07.57: [18477]: --> [2:OK]
Apr 13 23:47:07.57: [18477]: <-- [24:AT+FDCC=7,D,2,2,0,2,0,0\r]
Apr 13 23:47:07.57: [18477]: --> [2:OK]
Apr 13 23:47:07.57: [18477]: DIAL 6023241958
Apr 13 23:47:07.57: [18477]: <-- [22:ATS0=255;DT6023241958\r]
Apr 13 23:47:15.30: [18477]: --> [5:+FCON]
Apr 13 23:47:15.30: [18477]: --> [28:+FCSI:"ATC-Onlane, Inc.    "]
Apr 13 23:47:15.30: [18477]: REMOTE CSI "ATC-Onlane, Inc."
Apr 13 23:47:15.30: [18477]: --> [22:+FDIS: 2,5,2,2,0,2,0,0]
Apr 13 23:47:15.30: [18477]: --> [2:OK]
Apr 13 23:47:15.30: [18477]: REMOTE best rate 14400 bit/s
Apr 13 23:47:15.30: [18477]: REMOTE max A3 page width (303 mm)
Apr 13 23:47:15.30: [18477]: REMOTE max unlimited page length
Apr 13 23:47:15.30: [18477]: REMOTE best vres 15.4 line/mm
Apr 13 23:47:15.30: [18477]: REMOTE format support: MH
Apr 13 23:47:15.30: [18477]: REMOTE supports T.30 Annex C, half duplex
ECM
Apr 13 23:47:15.30: [18477]: REMOTE best 0 ms/scanline
Apr 13 23:47:15.30: [18477]: USE 14400 bit/s
Apr 13 23:47:15.30: [18477]: USE error correction mode
Apr 13 23:47:15.30: [18477]: SEND file "docq/doc18.ps;0181"
Apr 13 23:47:15.30: [18477]: High resolution document is not supported
by client, image resolution 7.71654 lines/mm
Apr 13 23:47:15.30: [18477]: <-- [5:ATH0\r]
Apr 13 23:47:15.30: [18477]: --> [2:OK]
Apr 13 23:47:15.30: [18477]: SESSION END

So figure the reject comes from the Eicon driver itself as the above log
doesn't show Hylafax to ever get the connect. Both Eicon boards are set
to do Class2 with 57600 serial speed.

From the Patton 2977 setup the fax goes through fine. Anyone got a hint
what config I need to tune to make this work?

Regards, Ulf.


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*