Re: [hylafax-users] No Sending / Receiving Possible With Devolo FUN II Modem CLASS 1

[NeroZero <support4fpo@xxxxxxx>]

@ Darren, does it still bounce to the list???


Your job to 555 failed because:

Failure to train remote modem at 2400 bps or minimum speed; Giving up
after 3 attempts to send same page


    ---- Transcript of session follows ----

Feb 09 01:54:26.09: [21287]: SESSION BEGIN 000000021 14157674
Feb 09 01:54:26.09: [21287]: HylaFAX (tm) Version 4.3.1
Feb 09 01:54:26.09: [21287]: SEND FAX: JOB 6 DEST 555 COMMID 000000021
DEVICE '/dev/ttyS0' FROM 'dau <dau@xxxxxxxx>' USER dau
Feb 09 01:54:26.09: [21287]: <-- [12:AT+FCLASS=1\r]
Feb 09 01:54:26.12: [21287]: --> [2:OK]
Feb 09 01:54:26.12: [21287]: DIAL 555
Feb 09 01:54:26.12: [21287]: <-- [11:ATDT0W555\r]
Feb 09 01:54:49.59: [21287]: --> [7:CONNECT]
Feb 09 01:54:51.09: [21287]: --> [2:OK]
Feb 09 01:54:51.09: [21287]: REMOTE NSF "50 80 00 16 00 00 02 00 00 00
00 00 00 00 00 00 00 00 00 FF"
Feb 09 01:54:51.09: [21287]: NSF remote fax equipment: unknown
Feb 09 01:54:51.09: [21287]: <-- [9:AT+FRH=3\r]
Feb 09 01:54:51.10: [21287]: --> [7:CONNECT]
Feb 09 01:54:51.78: [21287]: --> [2:OK]
Feb 09 01:54:51.78: [21287]: REMOTE CSI ""
Feb 09 01:54:51.78: [21287]: <-- [9:AT+FRH=3\r]
Feb 09 01:54:51.79: [21287]: --> [7:CONNECT]
Feb 09 01:54:52.01: [21287]: --> [2:OK]
Feb 09 01:54:52.01: [21287]: REMOTE best rate 9600 bit/s
Feb 09 01:54:52.01: [21287]: REMOTE max A4 page width (215 mm)
Feb 09 01:54:52.01: [21287]: REMOTE max unlimited page length
Feb 09 01:54:52.01: [21287]: REMOTE best vres 7.7 line/mm
Feb 09 01:54:52.01: [21287]: REMOTE format support: MH, MR
Feb 09 01:54:52.01: [21287]: REMOTE best 20 ms, 10 ms/scanline
Feb 09 01:54:52.01: [21287]: USE 9600 bit/s
Feb 09 01:54:52.01: [21287]: SEND file "docq/cover6;c1"
Feb 09 01:54:52.01: [21287]: USE A4 page width (215 mm)
Feb 09 01:54:52.01: [21287]: USE unlimited page length
Feb 09 01:54:52.01: [21287]: USE 7.7 line/mm
Feb 09 01:54:52.01: [21287]: USE 2-D MR
Feb 09 01:54:52.01: [21287]: USE 10 ms/scanline
Feb 09 01:54:52.01: [21287]: SEND training at v.29 9600 bit/s
Feb 09 01:54:52.01: [21287]: <-- [9:AT+FRS=7\r]
Feb 09 01:55:22.02: [21287]: MODEM <Timeout>
Feb 09 01:55:22.02: [21287]: Failure to receive silence.
Feb 09 01:55:22.02: [21287]: Error sending T.30 prologue frames
Feb 09 01:55:22.02: [21287]: SEND training at v.29 7200 bit/s
Feb 09 01:55:22.02: [21287]: <-- [9:AT+FRS=7\r]
Feb 09 01:55:22.04: [21287]: --> [2:OK]
Feb 09 01:55:22.04: [21287]: <-- [9:AT+FTH=3\r]
Feb 09 01:55:22.11: [21287]: --> [7:CONNECT]
Feb 09 01:55:23.10: [21287]: --> [7:CONNECT]
Feb 09 01:55:24.13: [21287]: --> [2:OK]
Feb 09 01:55:24.13: [21287]: <-- [9:AT+FTS=7\r]
Feb 09 01:55:24.21: [21287]: --> [2:OK]
Feb 09 01:55:24.21: [21287]: <-- [10:AT+FTM=72\r]
Feb 09 01:55:24.51: [21287]: --> [7:CONNECT]
Feb 09 01:55:26.32: [21287]: --> [2:OK]
Feb 09 01:55:26.32: [21287]: <-- [9:AT+FRH=3\r]
Feb 09 01:55:26.85: [21287]: --> [7:CONNECT]
Feb 09 01:55:26.90: [21287]: --> [5:ERROR]
Feb 09 01:55:26.90: [21287]: MODEM Command error
Feb 09 01:55:26.90: [21287]: FCS error
Feb 09 01:55:26.90: [21287]: <-- [9:AT+FRS=7\r]
Feb 09 01:55:56.90: [21287]: MODEM <Timeout>
Feb 09 01:55:56.90: [21287]: DELAY 1500 ms
Feb 09 01:55:58.40: [21287]: SEND training at v.27ter 4800 bit/s
Feb 09 01:55:58.40: [21287]: <-- [9:AT+FRS=7\r]
Feb 09 01:55:58.43: [21287]: --> [2:OK]
Feb 09 01:55:58.43: [21287]: <-- [9:AT+FTH=3\r]
Feb 09 01:55:58.51: [21287]: --> [7:CONNECT]
Feb 09 01:55:59.50: [21287]: --> [7:CONNECT]
Feb 09 01:56:00.52: [21287]: --> [2:OK]
Feb 09 01:56:00.52: [21287]: <-- [9:AT+FTS=7\r]
Feb 09 01:56:00.60: [21287]: --> [2:OK]
Feb 09 01:56:00.60: [21287]: <-- [10:AT+FTM=48\r]
Feb 09 01:56:01.56: [21287]: --> [7:CONNECT]
Feb 09 01:56:03.38: [21287]: --> [2:OK]
Feb 09 01:56:03.38: [21287]: <-- [9:AT+FRH=3\r]
Feb 09 01:56:06.48: [21287]: --> [0:]
Feb 09 01:56:06.48: [21287]: MODEM <Empty line>
Feb 09 01:56:06.49: [21287]: --> [2:OK]
Feb 09 01:56:06.49: [21287]: DELAY 1500 ms
Feb 09 01:56:07.99: [21287]: SEND training at v.27ter fallback mode 2400
bit/s
Feb 09 01:56:07.99: [21287]: <-- [9:AT+FRS=7\r]
Feb 09 01:56:08.74: [21287]: --> [2:OK]
Feb 09 01:56:08.74: [21287]: <-- [9:AT+FTH=3\r]
Feb 09 01:56:08.81: [21287]: --> [7:CONNECT]
Feb 09 01:56:09.80: [21287]: --> [7:CONNECT]
Feb 09 01:56:10.83: [21287]: --> [2:OK]
Feb 09 01:56:10.83: [21287]: <-- [9:AT+FTS=7\r]
Feb 09 01:56:10.91: [21287]: --> [2:OK]
Feb 09 01:56:10.91: [21287]: <-- [10:AT+FTM=24\r]
Feb 09 01:56:12.11: [21287]: --> [7:CONNECT]
Feb 09 01:56:13.95: [21287]: --> [2:OK]
Feb 09 01:56:13.95: [21287]: <-- [9:AT+FRH=3\r]
Feb 09 01:56:17.07: [21287]: --> [0:]
Feb 09 01:56:17.07: [21287]: MODEM <Empty line>
Feb 09 01:56:17.09: [21287]: --> [2:OK]
Feb 09 01:56:17.09: [21287]: DELAY 1500 ms
Feb 09 01:56:18.59: [21287]: TRAINING failed
Feb 09 01:56:18.59: [21287]: SEND: Failure to train remote modem at 2400
bps or minimum speed; Giving up after 3 attempts to send same page
"docq/cover6;c1", dirnum 0
Feb 09 01:56:18.59: [21287]: <-- [9:AT+FTH=3\r]
Feb 09 01:56:18.66: [21287]: --> [7:CONNECT]
Feb 09 01:56:19.90: [21287]: --> [2:OK]
Feb 09 01:56:19.90: [21287]: <-- [5:ATH0\r]
Feb 09 01:56:20.21: [21287]: --> [2:OK]
Feb 09 01:56:20.21: [21287]: SESSION END

------- Unsent job status -------
      Destination: 555
            JobID: 6
          GroupID: 6
           Sender:
         Mailaddr:
          CommID: 000000021
            Modem: any
   Submitted From: localhost
       Page Width: 209  (mm)
      Page Length: 296 (mm)
       Resolution: 196 (lpi)
           Status: Failure to train remote modem at 2400 bps or minimum
speed; Giving up after 3 attempts to send same page
          Dialogs: 3
            Dials: 0
            Calls: 3
            Pages: 0
         TotPages: 2
         Attempts: 3
           Dirnum:


faxguy@xxxxxxxxxxxxxxxx wrote:
> NeroZero wrote:
>
>> Under hyla it is doing the same time out. Where do I get the error
>> log there?
>>
>
> /var/spool/hylafax/log
>
> Lee.
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
>  To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*