[hylafax-users] Remote fax answers but fails

["bubba" <bubba@xxxxxxxxxxxxxxx>]

Title: Message

OK I can not get any fax machine or even another HylaFax server to receive a fax using Hylafax

 

Jan 04 14:56:16.28: [ 2932]: SESSION BEGIN 000000034 593042285555555 Jan 04 14:56:16.28: [ 2932]: HylaFAX (tm) Version 4.3.0.7 Jan 04 14:56:16.28: [ 2932]: SEND FAX: JOB 7 DEST 2285555555 COMMID 000000034 DEVICE '/dev/ttyIAX1' FROM '4120 <bubba@xxxxxxxxxxxx>' USER 4120 Jan 04 14:56:16.28: [ 2932]: STATE CHANGE: RUNNING -> SENDING Jan 04 14:56:16.28: [ 2932]: <-- [12:AT+FCLASS=1\r] Jan 04 14:56:16.28: [ 2932]: --> [2:OK] Jan 04 14:56:16.28: [ 2932]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled Jan 04 14:56:16.28: [ 2932]: DIAL 2285555555 Jan 04 14:56:16.28: [ 2932]: <-- [15:ATDT2285555555\r] Jan 04 14:56:27.15: [ 2932]: --> [7:CONNECT] Jan 04 14:56:28.57: [ 2932]: --> HDLC<19:FF C0 04 B5 00 6C 04 00 A2 00 30 D6 76 C4 43 00 FE 4B 9B> Jan 04 14:56:28.57: [ 2932]: --> [2:OK] Jan 04 14:56:28.57: [ 2932]: REMOTE NSF "AD 00 36 20 00 45 00 0C 6B 6E 23 C2 00 7F" Jan 04 14:56:28.57: [ 2932]: NSF remote fax equipment: HP LaserJet 3150 Jan 04 14:56:28.57: [ 2932]: <-- [9:AT+FRH=3\r] Jan 04 14:56:29.27: [ 2932]: --> [7:CONNECT] Jan 04 14:56:29.27: [ 2932]: --> HDLC<25:FF C0 02 EC 4C 9C 9C 04 AC EC AC 04 1C 4C 4C 04 04 04 04 04 04 04 04 0A D6> Jan 04 14:56:29.27: [ 2932]: --> [2:OK] Jan 04 14:56:29.27: [ 2932]: REMOTE CSI "228 555 5555" Jan 04 14:56:29.27: [ 2932]: <-- [9:AT+FRH=3\r] Jan 04 14:56:29.71: [ 2932]: --> [7:CONNECT] Jan 04 14:56:29.71: [ 2932]: --> HDLC<15:FF C8 01 00 77 1F 23 01 49 01 01 01 06 D0 B8> Jan 04 14:56:29.81: [ 2932]: --> [2:OK] Jan 04 14:56:29.81: [ 2932]: REMOTE best rate 14400 bit/s Jan 04 14:56:29.81: [ 2932]: REMOTE max A4 page width (215 mm) Jan 04 14:56:29.81: [ 2932]: REMOTE max unlimited page length Jan 04 14:56:29.81: [ 2932]: REMOTE best vres 300 x 300 dpi Jan 04 14:56:29.81: [ 2932]: REMOTE format support: MH, MR, MMR, JBIG Jan 04 14:56:29.81: [ 2932]: REMOTE supports T.30 Annex A, 256-byte ECM Jan 04 14:56:29.81: [ 2932]: REMOTE best 0 ms/scanline Jan 04 14:56:29.81: [ 2932]: USE 14400 bit/s Jan 04 14:56:29.81: [ 2932]: USE error correction mode Jan 04 14:56:29.81: [ 2932]: <-- [9:AT+FTH=3\r] Jan 04 14:56:29.83: [ 2932]: --> [7:CONNECT] Jan 04 14:56:29.83: [ 2932]: <-- HDLC<3:FF C8 DF> Jan 04 14:56:31.01: [ 2932]: --> [2:OK] Jan 04 14:56:31.01: [ 2932]: MODEM input buffering enabled Jan 04 14:56:31.01: [ 2932]: <-- [5:ATH0\r] Jan 04 14:56:31.11: [ 2932]: --> [2:OK] Jan 04 14:56:31.11: [ 2932]: MODEM set DTR OFF Jan 04 14:56:31.11: [ 2932]: MODEM set baud rate: 0 baud (flow control unchanged) Jan 04 14:56:31.11: [ 2932]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5) Jan 04 14:56:31.11: [ 2932]: SESSION END

 

 

 

 

Bubba