Re: [hylafax-users] mis-interpreted senderID?

[Mark <hylafax2@xxxxxxxxxx>]

Lee Howard <faxguy <at> howardsilvan.com> writes:

> That said, I think that this excersize has exposed a bug in the Class 2 
> firmware that I think can be avoided by padding the LocalIdentifier with 
> whitespaces.  Try modifying LocalIdentifier in the modem config file to 
> this:
> 
>   LocalIdentifier:  "+4618343428         "
> 
> That may prevent the bug in the Class 2 firmware from surfacing.
> 
> Lee.

Hi Lee, Today I did the padding you requested but no change was detected. The
received fax still shows the same 0q stuff, as the padding after the senderID
was was stripped off. I used FAXNumber:	"+4618343428         "   on the sending
Intertex modem.

If this is not something that can be dealt with within HylaFax, maybe I will
simply use a regexp and strip off "0q\s*" and similar problem strings as I see
them arise from inbound senderIDs a local "fix."  What do you think of that?

Dec 14 08:41:08.50: [ 4018]: SESSION BEGIN 000000661 4618341083
Dec 14 08:41:08.50: [ 4018]: HylaFAX (tm) Version 4.3.0.11
Dec 14 08:41:08.50: [ 4018]: <-- [4:ATA\r]
Dec 14 08:41:14.58: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:14.58: [ 4018]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS4'
Dec 14 08:41:14.58: [ 4018]: RECV FAX: begin
Dec 14 08:41:14.63: [ 4018]: <-- data [35]
Dec 14 08:41:14.63: [ 4018]: <-- data [2]
Dec 14 08:41:14.66: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:14.66: [ 4018]: <-- data [23]
Dec 14 08:41:14.67: [ 4018]: <-- data [2]
Dec 14 08:41:14.69: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:14.69: [ 4018]: <-- data [13]
Dec 14 08:41:14.69: [ 4018]: <-- data [2]
Dec 14 08:41:16.97: [ 4018]: --> [2:OK]
Dec 14 08:41:16.97: [ 4018]: <-- [9:AT+FRH=3\r]
Dec 14 08:41:17.20: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:18.94: [ 4018]: --> [2:OK]
Dec 14 08:41:18.94: [ 4018]: REMOTE TSI "0q       +4618343428"
Dec 14 08:41:18.94: [ 4018]: <-- [9:AT+FRH=3\r]
Dec 14 08:41:18.96: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:19.29: [ 4018]: --> [2:OK]
Dec 14 08:41:19.29: [ 4018]: REMOTE wants 14400 bit/s
Dec 14 08:41:19.29: [ 4018]: REMOTE wants A4 page width (215 mm)
Dec 14 08:41:19.29: [ 4018]: REMOTE wants unlimited page length
Dec 14 08:41:19.29: [ 4018]: REMOTE wants 7.7 line/mm
Dec 14 08:41:19.29: [ 4018]: REMOTE wants 1-D MH
Dec 14 08:41:19.29: [ 4018]: RECV training at v.17 14400 bit/s
Dec 14 08:41:19.29: [ 4018]: <-- [11:AT+FRM=145\r]
Dec 14 08:41:19.36: [ 4018]: --> [8:+FCERROR]
Dec 14 08:41:19.36: [ 4018]: <-- [11:AT+FRM=145\r]
Dec 14 08:41:21.06: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:22.54: [ 4018]: RECV: TCF 2672 bytes, 0% non-zero, 2670 zero-run
Dec 14 08:41:22.54: [ 4018]: --> [10:NO CARRIER]
Dec 14 08:41:22.54: [ 4018]: <-- [9:AT+FRS=7\r]
Dec 14 08:41:22.62: [ 4018]: --> [2:OK]
Dec 14 08:41:22.62: [ 4018]: TRAINING succeeded
Dec 14 08:41:22.63: [ 4018]: <-- [9:AT+FTH=3\r]
Dec 14 08:41:23.49: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:23.49: [ 4018]: <-- data [3]
Dec 14 08:41:23.49: [ 4018]: <-- data [2]
Dec 14 08:41:23.81: [ 4018]: --> [2:OK]
Dec 14 08:41:23.81: [ 4018]: <-- [11:AT+FRM=146\r]
Dec 14 08:41:24.59: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:24.59: [ 4018]: RECV: begin page
Dec 14 08:41:27.69: [ 4018]: RECV: 282 total lines, 0 bad lines, 0 consecutive
bad lines
Dec 14 08:41:27.69: [ 4018]: RECV: end page
Dec 14 08:41:27.69: [ 4018]: --> [10:NO CARRIER]
Dec 14 08:41:27.69: [ 4018]: <-- [9:AT+FRH=3\r]

Dec 14 08:41:30.08: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:30.08: [ 4018]: <-- data [3]
Dec 14 08:41:30.08: [ 4018]: <-- data [2]
Dec 14 08:41:30.50: [ 4018]: --> [2:OK]
Dec 14 08:41:30.51: [ 4018]: RECV send MCF (message confirmation)
Dec 14 08:41:30.51: [ 4018]: RECV FAX (000000661): from 0q       +4618343428,
page 1 in 0:13, INF, 7.7 line/mm, 1-D MH, 14400 bit/s
Dec 14 08:41:31.51: [ 4018]: RECV FAX (000000661): recvq/fax000000378.tif from
0q       +4618343428, route to <unspecified>, 1 pages in 0:16
Dec 14 08:41:31.51: [ 4018]: <-- [9:AT+FRH=3\r]
Dec 14 08:41:31.75: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:31.94: [ 4018]: --> [10:NO CARRIER]
Dec 14 08:41:31.94: [ 4018]: MODEM No carrier
Dec 14 08:41:31.94: [ 4018]: <-- [9:AT+FRS=7\r]
Dec 14 08:41:32.13: [ 4018]: --> [2:OK]
Dec 14 08:41:32.13: [ 4018]: <-- [9:AT+FTH=3\r]
Dec 14 08:41:33.09: [ 4018]: --> [7:CONNECT]
Dec 14 08:41:33.09: [ 4018]: <-- data [3]
Dec 14 08:41:33.09: [ 4018]: <-- data [2]
Dec 14 08:41:33.52: [ 4018]: --> [2:OK]
Dec 14 08:41:33.52: [ 4018]: RECV send CRP (command repeat)
Dec 14 08:41:33.52: [ 4018]: <-- [9:AT+FRH=3\r]
Dec 14 08:41:40.52: [ 4018]: --> [0:]
Dec 14 08:41:40.52: [ 4018]: MODEM <Empty line>
Dec 14 08:41:40.52: [ 4018]: <-- data [1]
Dec 14 08:41:40.62: [ 4018]: --> [2:]
Dec 14 08:41:40.62: [ 4018]: --> [2:OK]
Dec 14 08:41:40.62: [ 4018]: RECV FAX: bin/faxrcvd "recvq/fax000000378.tif"
"ttyS4" "000000661" ""
Dec 14 08:41:40.63: [ 4018]: RECV FAX: end
Dec 14 08:41:40.63: [ 4018]: SESSION END
 


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*