HylaFAX The world's most advanced open source fax server |
Hello Julius, there is a config.modem script at the elsa homepage. Search for hylafax in the support database. Also I made as config.modem script for the Microlink 56k basic. Maybe you must change a bit. regards Stephan Storath Julius schrieb: > > Hi, > I am new on the list. > I need help in configuring hylafax-v4.0pl2-52 with SUSE Linux 6.1 > and the obove Modem. Firmware 1.67. > I need fax in and out, and I want to use the same line > for ppp login. > > I cannot find the correct settings for /var/spool/fax/etc/config.modem. > Is anybody out there firm with that piece of hardware. > > faxaddmodem finds the modem as a Class1 modem. > > The archive of this list I have read already butone mail I have found > did not help. > Greetings from Germany > Julius > > -- > Praxis Storath: Powered by linuX (Ver: SuSE 5.3) ; linuX-DAVID > - have another nice night with that great OS linuX (TM) made by > Internet > - blue - screens for linuX background only - REG. USER 72969
# # Class 2.0 modem configuration for ELSA 33.6 TQV. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 49 AreaCode: 7306 FAXNumber: +49.7306.919594 LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: "etc/dialrules" ServerTracing: 11 SessionTracing: 11 RecvFileMode: 0644 LogFileMode: 0644 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: quiet GettyArgs: "-h %l %s" LocalIdentifier: "Kling & Bauer" #LogFacility: local7 TagLineFont: etc/lutRS18.pcf TagLineFormat: "%%l|%c|Seite %%p von %%t" PercentGoodLines: 80 MaxConsecutiveBadLines: 20 MaxRecvPages: 50 ModemPriority: 200 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2.0 # use this to supply a hint ModemRate: 115200 # max rate for DCE-DTE communication ModemFlowControl: rtscts # XON/XOFF flow control assumed ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) # # We normally append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT%s #ModemDialCmd: "ATX0\nATDT0%s" # no '@' 'cuz then busy not recognized ModemDialCmd: "ATDT0%s" # no '@' 'cuz then busy not recognized # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # ModemResetCmds: ATX3 # stuff to do when modem is reset ModemAnswerCmd: ATA # use this to answer phone ModemNoFlowCmd: AT&K ModemHardFlowCmd: AT&K3 ModemSoftFlowCmd: AT&K1 ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" ModemEchoOffCmd: ATE0 # disable command echo ModemVerboseResultsCmd: ATV1 # enable verbose command results ModemResultCodesCmd: ATQ0 # enable result codes ModemOnHookCmd: ATH # place phone on hook (hangup) ModemSoftResetCmd: ATZ # do soft reset of modem ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds ModemRecvFillOrder: LSB2MSB # bit order of received facsimile ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # # Configuration parameters for Class 2.0 modems. # Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0 Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct) Class2CQCmd: "" # commands to enable copy quality proc. Class2AbortCmd: AT+FKS # abort session command Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities Class2TBCCmd: AT+FPP=0 # setup stream mode Class2CRCmd: AT+FCR=1 # enable capability to receive Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing Class2LIDCmd: AT+FLI # set local identifier command Class2DCCCmd: AT+FCC # set modem capabilities command Class2DISCmd: AT+FIS # set session parameters command Class2DDISCmd: "" # disable pre-dial DIS command hack Class2CIGCmd: AT+FPI # set polling identifier command Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command Class2PIECmd: AT+FIE=0 # disable interrupt-enable command Class2PTSCmd: AT+FPS # set post-page status command Class2SPLCmd: AT+FSP # set polling indicator command Class2NFLOCmd: AT+FLO=0 # set no flow control command Class2SFLOCmd: AT+FLO=1 # set software flow control command Class2HFLOCmd: AT+FLO=2 # set hardware flow control command Class2APQueryCmd: AT+FAP=?