Difference between revisions of "HylaFAX Status Codes"

000-049 : call failures
===============================================================================
000      : Call successful
001      : Busy signal detected
002      : No carrier detected
003      : No answer from remote
004      : No local dialtone
005      : Invalid dialing command
006      : Unknown problem
007      : Carrier established, but Phase A failure
008      : Data connection established (wanted fax)
009      : Glare - RING detected
010      : Blacklisted by modem
011      : Ringback detected, no answer without CED
012      : Ring detected without successful handshake

050-099 : non Class-specific fax protocol failures
===============================================================================
050      : Missing EOL after 5 seconds
051      : Procedure interrupt received, job terminated

100-199 : Class 1-specific protocol failure
===============================================================================
100      : Failure to receive silence (synchronization failure).
101      : Failure to raise V.21 transmission carrier.
102      : No sender protocol (T.30 T1 timeout)
103      : RSPREC error/got DCN (sender abort)
104      : RSPREC invalid response received
105      : Failure to train modems
106      : RSPREC error/got EOT
107      : Can not continue after DIS/DTC
108      : COMREC received DCN (sender abort)
109      : No response to RNR repeated 3 times.
110      : COMREC invalid response received
111      : V.21 signal reception timeout; expected page possibly not received in full
112      : Failed to properly detect high-speed data carrier.
113      : Received invalid CTC signal in V.34-Fax.
114      : Failed to properly open V.34 primary channel.
115      : Received premature V.34 termination.
116      : Failed to properly open V.34 control channel.
117      : COMREC invalid response to repeated PPR received
118      : T.30 T2 timeout, expected signal not received
119      : COMREC invalid partial-page signal received
120      : Cannot synchronize ECM frame reception.
121      : ECM page received containing no image data.
122      : Remote has no T.4 receiver capability
123      : DTC received when expecting DIS (not supported)
124      : COMREC error in transmit Phase B/got DCN
125      : COMREC invalid command received/no DIS or DTC
126      : No receiver protocol (T.30 T1 timeout)
127      : Stop and wait failure (modem on hook)
128      : Remote fax disconnected prematurely
129      : Procedure interrupt (operator intervention)
130      : Unable to transmit page (giving up after RTN)
131      : Unable to transmit page (giving up after 3 attempts)
132      : Unable to transmit page (NAK at all possible signalling rates)
133      : Unable to transmit page (NAK with operator intervention)
134      : Fax protocol error (unknown frame received)
135      : Fax protocol error (command repeated 3 times)
136      : DIS/DTC received 3 times; DCS not recognized
137      : Failure to train remote modem at 2400 bps or minimum speed
138      : Receiver flow control exceeded timer.
139      : No response to RR repeated 3 times.
140      : COMREC invalid response received to RR.
141      : No response to CTC repeated 3 times.
142      : COMREC invalid response received to CTC.
143      : Failure to transmit clean ECM image data.
144      : No response to EOR repeated 3 times.
145      : COMREC invalid response received to EOR.
146      : COMREC invalid response received to PPS.
147      : No response to PPS repeated 3 times.
148      : Unable to establish message carrier
149      : Unspecified Transmit Phase C error
150      : No response to MPS repeated 3 tries
151      : No response to EOP repeated 3 tries
152      : No response to EOM repeated 3 tries
153      : No response to PPM repeated 3 tries
154      : Timeout waiting for Phase C carrier drop
155      : PPM received with no image data.  To continue risks receipt confirmation.

200-299 : Class 2-specific protocol failure
===============================================================================
200      : Unable to request polling operation (modem may not support polling)
201      : Unable to setup polling identifer (modem command failed)
202      : Unable to setup selective polling address (modem command failed)
203      : Unable to setup polling password (modem command failed)
204      : Unable to send password (modem command failed)
205      : Unable to send subaddress (modem command failed)
206      : Unable to restrict minimum transmit speed to %s (modem command failed)
207      : Unable to setup session parameters prior to call (modem command failed)
208      : Unable to set session parameters
209      :
210      : Unknown hangup code
211      : Normal and proper end of connection
212      : Ring detect without successful handshake
213      : Call aborted,  from +FK or <CAN>
214      : No loop current
215      : Ringback detected, no answer (timeout)
216      : Ringback detected, no answer without CED
217      : Unspecified Phase A error
218      : No answer (T.30 T1 timeout)
219      : Unspecified Transmit Phase B error
220      : Remote cannot be polled
221      : COMREC error in transmit Phase B/got DCN
222      : COMREC invalid command received/no DIS or DTC
223      : RSPREC error/got DCN
224      : DCS sent 3 times without response
225      : DIS/DTC received 3 times; DCS not recognized
226      : Failure to train at 2400 bps or +FMINSP value
227      : RSPREC invalid response received
228      : Unspecified Transmit Phase C error
229      : Unspecified Image format error
230      : Image conversion error
231      : DTE to DCE data underflow
232      : Unrecognized Transparent data command
233      : Image error, line length wrong
234      : Image error, page length wrong
235      : Image error, wrong compression code
236      : Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command
237      : RSPREC error/got DCN
238      : No response to MPS repeated 3 times
239      : Invalid response to MPS
240      : No response to EOP repeated 3 times
241      : Invalid response to EOP
242      : No response to EOM repeated 3 times
243      : Invalid response to EOM
244      : Unable to continue after PIN or PIP
245      : Unspecified Receive Phase B error
246      : RSPREC error/got DCN
247      : COMREC error
248      : T.30 T2 timeout, expected page not received
249      : T.30 T1 timeout after EOM received
250      : Unspecified Phase C error, including too much delay between TCF and +FDR command
251      : Missing EOL after 5 seconds (section 3.2/T.4)
252      : DCE to DTE buffer overflow
253      : Bad CRC or frame (ECM or BFT modes)
254      : Unspecified Phase D error
255      : RSPREC invalid response received
256      : COMREC invalid response received
257      : Unable to continue after PIN or PIP, no PRI-Q
258      : Command or signal 10 sec. timeout
259      : Cannot send: +FMINSP > remote's +FDIS(BR) code
260      : Cannot send: remote is V.29 only, local DCE constrained to 2400 or 4800 bps
261      : Remote station cannot receive (DIS bit 10)
262      : +FK aborted or <CAN> aborted
263      : +Format conversion error in +FDT=DF,VR, WD,LN Incompatible and inconvertable data format
264      : Remote cannot receive
265      : After +FDR, DCE waited more than 30 seconds for XON from DTE after XOFF from DTE
266      : In Polling Phase B, remote cannot be polled
267-279 (currently unused)
280      : Procedure interrupt (operator intervention)
281      : Unable to transmit page (giving up after RTN)
282      : Unable to transmit page (giving up after 3 attempts)
283      : Unable to transmit page (NAK at all possible signalling rates)
284      : Unable to transmit page (NAK with operator intervention)
285      : Modem protocol error (unknown post-page response)
286      : Batching protocol error
287      : Communication failure during Phase B/C
288      : Communication failure during Phase B/C (modem protocol botch)

300-399 : Non-T.30 client or server failure
===============================================================================
301      : Receive aborted due to operator intervention
302      : Problem reading document directory
303      : Internal botch; %s post-page handling string "%s"
304      : Maximum receive page count exceeded, call terminated
305      : Could not fork for local ID.
306      : Bad exit status %#o for '%s'
307      : Could not open a pipe for local ID.
308      : ANSWER: CALL REJECTED
309      : ANSWER: Call deduced as %s, but told to answer as %s; call ignored
310      : External getty use is not permitted {E310}
311      : %s: could not create
312      : "%s: can not fork: %s
313      : ERROR: Unknown status
314      : Can not open document file %s
315      : Can not set directory %u in document file %s
316      : Error reading directory %u in document file %s
317      : Too many pages in submission; max %u
318      : Unable to lock shared document file
319      : Unable to open shared document file
320      : Unable to create document file
321      : Converted document is not valid TIFF
322      : Could not reopen converted document to verify format
323      : Job contains no documents
324      : Modem does not support polling
325      : Kill time expired
326      : Invalid or corrupted job description file
327      : REJECT: Unable to convert dial string to canonical format
328      : REJECT: Requested modem %s is not registered
329      : REJECT: No work found in job file
330      : REJECT: Page width (%u) appears invalid
331      : REJECT: Job expiration time (%u) appears invalid
332      : REJECT: Time-to-send (%u) appears invalid
333      : REJECT: Too many attempts to dial
334      : REJECT: Too many attempts to transmit: %u, max %u
335      : REJECT: Too many pages in submission: %u, max %u
336      : REJECT: Modem is configured as exempt from accepting jobs
337      : Blocked by concurrent calls
338      : Delayed by time-of-day restrictions
339      : Delayed by outbound call staggering
340      : Could not fork to prepare job for transmission
341      : Could not fork to start job transmission
342      : Delayed by prior call
343      : Send program terminated abnormally; unable to exec %s
344      : Job interrupted by user
345      : Call aborted by user
346      : Can not lock modem device
347      : %s  [document conversion failure output]
348      : REJECT: %s [JobControl reject notice]
350      : Permission denied (unnacceptable client TSI)
351      : Permission denied (unnacceptable client PWD)
352      : Send aborted due to operator intervention

400-499 : job/modem incompatibility
===============================================================================
400      : Modem does not support negotiated signalling rate
401      : Modem does not support negotiated min scanline time
402      : Document is not in a Group 3 or Group 4 compatible format (compression %u)
403      : Document was encoded with 2DMMR, but client does not support this data format
404      : Document was encoded with 2DMMR, but modem does not support this data format
405      : Document was encoded with 2DMMR, but ECM is not being used.
406      : Document was encoded with 2DMR, but client does not support this data format
407      : Document was encoded with 2DMR, but modem does not support this data format
408      : Hyperfine resolution document is not supported by client, image resolution %g x %g lines/mm
409      : Hyperfine resolution document is not supported by modem, image resolution %g x %g lines/mm
410      : Superfine resolution document is not supported by client, image resolution %g lines/mm
411      : Superfine resolution document is not supported by modem, image resolution %g lines/mm
412      : 300x300 resolution document is not supported by client, image resolution %g lines/mm
413      : 300x300 resolution document is not supported by modem, image resolution %g lines/mm
414      : High resolution document is not supported by client, image resolution %g lines/mm
415      : High resolution document is not supported by modem, image resolution %g lines/mm
416      : Client does not support document page width, max remote page width %g pixels, image width %lu pixels
417      : Modem does not support document page width, max page width %g pixels, image width %lu pixels
418      : Client does not support document page length, max remote page length %d mm, image length %lu rows (%.2f mm)
419      : Modem does not support document page length, max page length %s mm, image length %lu rows (%.2f mm)
420      : Unable to configure modem for fax use
421      : Unable to configure modem for data use
422      : Can not setup modem

500-E599 : paging failures
===============================================================================
500      : No initial ID response from paging central
501      : Login failed multiple times
502      : Protocol failure: %s from paging central
503      : Protocol failure: %s waiting for go-ahead message
504      : Message block not acknowledged by paging central after multiple tries
505      : Message block transmit failed paging central rejected it
506      : Protocol failure: paging central responded to message block transmit with forced disconnect
507      : Protocol failure: %s to message block transmit
508      : Paging central rejected content; check PIN
509      : Protocol failure: timeout waiting for transaction ACK/NAK from paging central
510      : Paging central responded with forced disconnect
511      : Job has no PIN to send to
512      : No PIN specified

600-699 : Polling failures
===============================================================================
601      : remote has no document to poll

900-999  : HylaFAX errors
===============================================================================
901      : Unable to open TIFF file %s for writing
902      : Unable to create temp file for received data: %s
903      : Can not set directory in document file
904      : Can not open document file
905      : Internal error: unable to open text message file
906      : Internal error: unable to read text message file
907      : polling operation not done because of internal failure
908      : Write error to file %s