000-049 : call failures
===============================================================================
000 : Call successful
001 : Busy signal detected
002 : No carrier detected
003 : No answer from remote
004 : No local dialtone
005 : Invalid dialing command
006 : Unknown problem
007 : Carrier established, but Phase A failure
008 : Data connection established (wanted fax)
009 : Glare - RING detected
010 : Blacklisted by modem
011 : Ringback detected, no answer without CED
012 : Ring detected without successful handshake
050-099 : non Class-specific fax protocol failures
===============================================================================
050 : Missing EOL after 5 seconds
051 : Procedure interrupt received, job terminated
100-199 : Class 1-specific protocol failure
===============================================================================
100 : Failure to receive silence (synchronization failure).
101 : Failure to raise V.21 transmission carrier.
102 : No sender protocol (T.30 T1 timeout)
103 : RSPREC error/got DCN (sender abort)
104 : RSPREC invalid response received
105 : Failure to train modems
106 : RSPREC error/got EOT
107 : Can not continue after DIS/DTC
108 : COMREC received DCN (sender abort)
109 : No response to RNR repeated 3 times.
110 : COMREC invalid response received
111 : V.21 signal reception timeout; expected page possibly not received in full
112 : Failed to properly detect high-speed data carrier.
113 : Received invalid CTC signal in V.34-Fax.
114 : Failed to properly open V.34 primary channel.
115 : Received premature V.34 termination.
116 : Failed to properly open V.34 control channel.
117 : COMREC invalid response to repeated PPR received
118 : T.30 T2 timeout, expected signal not received
119 : COMREC invalid partial-page signal received
120 : Cannot synchronize ECM frame reception.
121 : ECM page received containing no image data.
122 : Remote has no T.4 receiver capability
123 : DTC received when expecting DIS (not supported)
124 : COMREC error in transmit Phase B/got DCN
125 : COMREC invalid command received/no DIS or DTC
126 : No receiver protocol (T.30 T1 timeout)
127 : Stop and wait failure (modem on hook)
128 : Remote fax disconnected prematurely
129 : Procedure interrupt (operator intervention)
130 : Unable to transmit page (giving up after RTN)
131 : Unable to transmit page (giving up after 3 attempts)
132 : Unable to transmit page (NAK at all possible signalling rates)
133 : Unable to transmit page (NAK with operator intervention)
134 : Fax protocol error (unknown frame received)
135 : Fax protocol error (command repeated 3 times)
136 : DIS/DTC received 3 times; DCS not recognized
137 : Failure to train remote modem at 2400 bps or minimum speed
138 : Receiver flow control exceeded timer.
139 : No response to RR repeated 3 times.
140 : COMREC invalid response received to RR.
141 : No response to CTC repeated 3 times.
142 : COMREC invalid response received to CTC.
143 : Failure to transmit clean ECM image data.
144 : No response to EOR repeated 3 times.
145 : COMREC invalid response received to EOR.
146 : COMREC invalid response received to PPS.
147 : No response to PPS repeated 3 times.
148 : Unable to establish message carrier
149 : Unspecified Transmit Phase C error
150 : No response to MPS repeated 3 tries
151 : No response to EOP repeated 3 tries
152 : No response to EOM repeated 3 tries
153 : No response to PPM repeated 3 tries
154 : Timeout waiting for Phase C carrier drop
155 : PPM received with no image data. To continue risks receipt confirmation.
200-299 : Class 2-specific protocol failure
===============================================================================
200 : Unable to request polling operation (modem may not support polling)
201 : Unable to setup polling identifer (modem command failed)
202 : Unable to setup selective polling address (modem command failed)
203 : Unable to setup polling password (modem command failed)
204 : Unable to send password (modem command failed)
205 : Unable to send subaddress (modem command failed)
206 : Unable to restrict minimum transmit speed to %s (modem command failed)
207 : Unable to setup session parameters prior to call (modem command failed)
208 : Unable to set session parameters
209 :
210 : Unknown hangup code
211 : Normal and proper end of connection
212 : Ring detect without successful handshake
213 : Call aborted, from +FK or <CAN>
214 : No loop current
215 : Ringback detected, no answer (timeout)
216 : Ringback detected, no answer without CED
217 : Unspecified Phase A error
218 : No answer (T.30 T1 timeout)
219 : Unspecified Transmit Phase B error
220 : Remote cannot be polled
221 : COMREC error in transmit Phase B/got DCN
222 : COMREC invalid command received/no DIS or DTC
223 : RSPREC error/got DCN
224 : DCS sent 3 times without response
225 : DIS/DTC received 3 times; DCS not recognized
226 : Failure to train at 2400 bps or +FMINSP value
227 : RSPREC invalid response received
228 : Unspecified Transmit Phase C error
229 : Unspecified Image format error
230 : Image conversion error
231 : DTE to DCE data underflow
232 : Unrecognized Transparent data command
233 : Image error, line length wrong
234 : Image error, page length wrong
235 : Image error, wrong compression code
236 : Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command
237 : RSPREC error/got DCN
238 : No response to MPS repeated 3 times
239 : Invalid response to MPS
240 : No response to EOP repeated 3 times
241 : Invalid response to EOP
242 : No response to EOM repeated 3 times
243 : Invalid response to EOM
244 : Unable to continue after PIN or PIP
245 : Unspecified Receive Phase B error
246 : RSPREC error/got DCN
247 : COMREC error
248 : T.30 T2 timeout, expected page not received
249 : T.30 T1 timeout after EOM received
250 : Unspecified Phase C error, including too much delay between TCF and +FDR command
251 : Missing EOL after 5 seconds (section 3.2/T.4)
252 : DCE to DTE buffer overflow
253 : Bad CRC or frame (ECM or BFT modes)
254 : Unspecified Phase D error
255 : RSPREC invalid response received
256 : COMREC invalid response received
257 : Unable to continue after PIN or PIP, no PRI-Q
258 : Command or signal 10 sec. timeout
259 : Cannot send: +FMINSP > remote's +FDIS(BR) code
260 : Cannot send: remote is V.29 only, local DCE constrained to 2400 or 4800 bps
261 : Remote station cannot receive (DIS bit 10)
262 : +FK aborted or <CAN> aborted
263 : +Format conversion error in +FDT=DF,VR, WD,LN Incompatible and inconvertable data format
264 : Remote cannot receive
265 : After +FDR, DCE waited more than 30 seconds for XON from DTE after XOFF from DTE
266 : In Polling Phase B, remote cannot be polled
267-279 (currently unused)
280 : Procedure interrupt (operator intervention)
281 : Unable to transmit page (giving up after RTN)
282 : Unable to transmit page (giving up after 3 attempts)
283 : Unable to transmit page (NAK at all possible signalling rates)
284 : Unable to transmit page (NAK with operator intervention)
285 : Modem protocol error (unknown post-page response)
286 : Batching protocol error
287 : Communication failure during Phase B/C
288 : Communication failure during Phase B/C (modem protocol botch)
300-399 : Non-T.30 client or server failure
===============================================================================
301 : Receive aborted due to operator intervention
302 : Problem reading document directory
303 : Internal botch; %s post-page handling string "%s"
304 : Maximum receive page count exceeded, call terminated
305 : Could not fork for local ID.
306 : Bad exit status %#o for '%s'
307 : Could not open a pipe for local ID.
308 : ANSWER: CALL REJECTED
309 : ANSWER: Call deduced as %s, but told to answer as %s; call ignored
310 : External getty use is not permitted {E310}
311 : %s: could not create
312 : "%s: can not fork: %s
313 : ERROR: Unknown status
314 : Can not open document file %s
315 : Can not set directory %u in document file %s
316 : Error reading directory %u in document file %s
317 : Too many pages in submission; max %u
318 : Unable to lock shared document file
319 : Unable to open shared document file
320 : Unable to create document file
321 : Converted document is not valid TIFF
322 : Could not reopen converted document to verify format
323 : Job contains no documents
324 : Modem does not support polling
325 : Kill time expired
326 : Invalid or corrupted job description file
327 : REJECT: Unable to convert dial string to canonical format
328 : REJECT: Requested modem %s is not registered
329 : REJECT: No work found in job file
330 : REJECT: Page width (%u) appears invalid
331 : REJECT: Job expiration time (%u) appears invalid
332 : REJECT: Time-to-send (%u) appears invalid
333 : REJECT: Too many attempts to dial
334 : REJECT: Too many attempts to transmit: %u, max %u
335 : REJECT: Too many pages in submission: %u, max %u
336 : REJECT: Modem is configured as exempt from accepting jobs
337 : Blocked by concurrent calls
338 : Delayed by time-of-day restrictions
339 : Delayed by outbound call staggering
340 : Could not fork to prepare job for transmission
341 : Could not fork to start job transmission
342 : Delayed by prior call
343 : Send program terminated abnormally; unable to exec %s
344 : Job interrupted by user
345 : Call aborted by user
346 : Can not lock modem device
347 : %s [document conversion failure output]
348 : REJECT: %s [JobControl reject notice]
350 : Permission denied (unnacceptable client TSI)
351 : Permission denied (unnacceptable client PWD)
352 : Send aborted due to operator intervention
400-499 : job/modem incompatibility
===============================================================================
400 : Modem does not support negotiated signalling rate
401 : Modem does not support negotiated min scanline time
402 : Document is not in a Group 3 or Group 4 compatible format (compression %u)
403 : Document was encoded with 2DMMR, but client does not support this data format
404 : Document was encoded with 2DMMR, but modem does not support this data format
405 : Document was encoded with 2DMMR, but ECM is not being used.
406 : Document was encoded with 2DMR, but client does not support this data format
407 : Document was encoded with 2DMR, but modem does not support this data format
408 : Hyperfine resolution document is not supported by client, image resolution %g x %g lines/mm
409 : Hyperfine resolution document is not supported by modem, image resolution %g x %g lines/mm
410 : Superfine resolution document is not supported by client, image resolution %g lines/mm
411 : Superfine resolution document is not supported by modem, image resolution %g lines/mm
412 : 300x300 resolution document is not supported by client, image resolution %g lines/mm
413 : 300x300 resolution document is not supported by modem, image resolution %g lines/mm
414 : High resolution document is not supported by client, image resolution %g lines/mm
415 : High resolution document is not supported by modem, image resolution %g lines/mm
416 : Client does not support document page width, max remote page width %g pixels, image width %lu pixels
417 : Modem does not support document page width, max page width %g pixels, image width %lu pixels
418 : Client does not support document page length, max remote page length %d mm, image length %lu rows (%.2f mm)
419 : Modem does not support document page length, max page length %s mm, image length %lu rows (%.2f mm)
420 : Unable to configure modem for fax use
421 : Unable to configure modem for data use
422 : Can not setup modem
500-E599 : paging failures
===============================================================================
500 : No initial ID response from paging central
501 : Login failed multiple times
502 : Protocol failure: %s from paging central
503 : Protocol failure: %s waiting for go-ahead message
504 : Message block not acknowledged by paging central after multiple tries
505 : Message block transmit failed paging central rejected it
506 : Protocol failure: paging central responded to message block transmit with forced disconnect
507 : Protocol failure: %s to message block transmit
508 : Paging central rejected content; check PIN
509 : Protocol failure: timeout waiting for transaction ACK/NAK from paging central
510 : Paging central responded with forced disconnect
511 : Job has no PIN to send to
512 : No PIN specified
600-699 : Polling failures
===============================================================================
601 : remote has no document to poll
900-999 : HylaFAX errors
===============================================================================
901 : Unable to open TIFF file %s for writing
902 : Unable to create temp file for received data: %s
903 : Can not set directory in document file
904 : Can not open document file
905 : Internal error: unable to open text message file
906 : Internal error: unable to read text message file
907 : polling operation not done because of internal failure
908 : Write error to file %s
HylaFAX 
