 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] training failures
- To: Hylafax Mailling List <hylafax-users@xxxxxxxxxxx>
- Subject: [hylafax-users] training failures
- From: Graham Chiu <compkarori@xxxxxxxxx>
- Date: Tue, 13 Jul 2010 17:11:08 +1200
I swapped out my old external faxmodem for another as there were certain fax numbers I could not reach, but this new one seems worse as it seems 1/5 faxes can't be sent. It is fax over ip ... Jul 13 14:19:25.70: [13267]: SESSION BEGIN 000003581 XXXXXXXXXX Jul 13 14:19:25.70: [13267]: HylaFAX (tm) Version 4.3.0 Jul 13 14:19:25.70: [13267]: SEND FAX: JOB 1615 DEST 04-XXXXXXXXXX XXXXXXXXXX COMMID 000003581 DEVICE '/dev/ttyS0' FROM 'root ' USER root Jul 13 14:19:25.70: [13267]: <-- [12:AT+FCLASS=1\r] Jul 13 14:19:25.79: [13267]: --> [2:OK] Jul 13 14:19:25.79: [13267]: DIAL XXXXXXXXXX Jul 13 14:19:25.79: [13267]: <-- [14:ATDTXXXXXXXXXX\r] Jul 13 14:19:47.11: [13267]: --> [7:CONNECT] Jul 13 14:19:48.62: [13267]: --> [2:OK] Jul 13 14:19:48.62: [13267]: REMOTE NSF "AD 00 51 00 00 00 00 00" Jul 13 14:19:48.62: [13267]: NSF remote fax equipment: Telogy Networks Jul 13 14:19:48.62: [13267]: <-- [9:AT+FRH=3\r] Jul 13 14:19:48.64: [13267]: --> [7:CONNECT] Jul 13 14:19:49.42: [13267]: --> [2:OK] Jul 13 14:19:49.42: [13267]: REMOTE CSI "" Jul 13 14:19:49.42: [13267]: <-- [9:AT+FRH=3\r] Jul 13 14:19:49.44: [13267]: --> [7:CONNECT] Jul 13 14:19:49.98: [13267]: --> [2:OK] Jul 13 14:19:49.98: [13267]: REMOTE best rate 14400 bit/s Jul 13 14:19:49.98: [13267]: REMOTE max A4 page width (215 mm) Jul 13 14:19:49.98: [13267]: REMOTE max unlimited page length Jul 13 14:19:49.98: [13267]: REMOTE best vres 7.7 line/mm Jul 13 14:19:49.98: [13267]: REMOTE format support: MH Jul 13 14:19:49.98: [13267]: REMOTE best 0 ms/scanline Jul 13 14:19:49.98: [13267]: USE 9600 bit/s Jul 13 14:19:49.98: [13267]: SEND file "docq/doc1616.pdf;01" Jul 13 14:19:49.99: [13267]: USE A4 page width (215 mm) Jul 13 14:19:49.99: [13267]: USE unlimited page length Jul 13 14:19:49.99: [13267]: USE 7.7 line/mm Jul 13 14:19:49.99: [13267]: USE 1-D MH Jul 13 14:19:49.99: [13267]: USE 0 ms/scanline Jul 13 14:19:49.99: [13267]: SEND training at v.29 9600 bit/s Jul 13 14:19:49.99: [13267]: <-- [9:AT+FRS=7\r] Jul 13 14:20:19.99: [13267]: MODEM Jul 13 14:20:19.99: [13267]: Failure to receive silence. Jul 13 14:20:19.99: [13267]: Error sending T.30 prologue frames Jul 13 14:20:19.99: [13267]: SEND training at v.29 7200 bit/s Jul 13 14:20:19.99: [13267]: <-- [9:AT+FRS=7\r] Jul 13 14:20:20.00: [13267]: --> [2:OK] Jul 13 14:20:20.00: [13267]: <-- [9:AT+FTH=3\r] Jul 13 14:20:20.02: [13267]: --> [7:CONNECT] Jul 13 14:20:20.02: [13267]: <-- data [23] Jul 13 14:20:20.02: [13267]: <-- data [2] Jul 13 14:20:21.72: [13267]: --> [7:CONNECT] Jul 13 14:20:21.73: [13267]: <-- data [6] Jul 13 14:20:21.73: [13267]: <-- data [2] Jul 13 14:20:22.09: [13267]: --> [2:OK] Jul 13 14:20:22.09: [13267]: <-- [9:AT+FTS=7\r] Jul 13 14:20:22.24: [13267]: --> [2:OK] Jul 13 14:20:22.25: [13267]: <-- [10:AT+FTM=72\r] Jul 13 14:20:22.26: [13267]: --> [7:CONNECT] Jul 13 14:20:22.26: [13267]: <-- data [1024] Jul 13 14:20:22.26: [13267]: <-- data [326] Jul 13 14:20:22.26: [13267]: <-- data [2] Jul 13 14:20:24.02: [13267]: --> [2:OK] Jul 13 14:20:24.02: [13267]: <-- [9:AT+FRH=3\r] Jul 13 14:20:27.12: [13267]: --> [0:] Jul 13 14:20:27.12: [13267]: MODEM Jul 13 14:20:27.12: [13267]: <-- data [1] Jul 13 14:20:27.13: [13267]: --> [2:OK] Jul 13 14:20:27.13: [13267]: DELAY 1500 ms Jul 13 14:20:28.63: [13267]: SEND training at v.27ter 4800 bit/s Jul 13 14:20:28.63: [13267]: <-- [9:AT+FRS=7\r] Jul 13 14:20:28.79: [13267]: --> [2:OK] Jul 13 14:20:28.79: [13267]: <-- [9:AT+FTH=3\r] Jul 13 14:20:28.80: [13267]: --> [7:CONNECT] Jul 13 14:20:28.80: [13267]: <-- data [23] Jul 13 14:20:28.80: [13267]: <-- data [2] Jul 13 14:20:30.51: [13267]: --> [7:CONNECT] Jul 13 14:20:30.51: [13267]: <-- data [6] Jul 13 14:20:30.51: [13267]: <-- data [2] Jul 13 14:20:30.88: [13267]: --> [2:OK] Jul 13 14:20:30.88: [13267]: <-- [9:AT+FTS=7\r] Jul 13 14:20:31.03: [13267]: --> [2:OK] Jul 13 14:20:31.03: [13267]: <-- [10:AT+FTM=48\r] Jul 13 14:20:31.05: [13267]: --> [7:CONNECT] Jul 13 14:20:31.05: [13267]: <-- data [900] Jul 13 14:20:31.05: [13267]: <-- data [2] Jul 13 14:20:33.45: [13267]: --> [2:OK] Jul 13 14:20:33.45: [13267]: <-- [9:AT+FRH=3\r] Jul 13 14:20:36.55: [13267]: --> [0:] Jul 13 14:20:36.55: [13267]: MODEM Jul 13 14:20:36.55: [13267]: <-- data [1] Jul 13 14:20:36.57: [13267]: --> [2:OK] Jul 13 14:20:36.57: [13267]: DELAY 1500 ms Jul 13 14:20:38.07: [13267]: SEND training at v.27ter fallback mode 2400 bit/s Jul 13 14:20:38.07: [13267]: <-- [9:AT+FRS=7\r] Jul 13 14:20:38.34: [13267]: --> [2:OK] Jul 13 14:20:38.34: [13267]: <-- [9:AT+FTH=3\r] Jul 13 14:20:38.36: [13267]: --> [7:CONNECT] Jul 13 14:20:38.36: [13267]: <-- data [23] Jul 13 14:20:38.36: [13267]: <-- data [2] Jul 13 14:20:40.07: [13267]: --> [7:CONNECT] Jul 13 14:20:40.07: [13267]: <-- data [6] Jul 13 14:20:40.07: [13267]: <-- data [2] Jul 13 14:20:40.43: [13267]: --> [2:OK] Jul 13 14:20:40.43: [13267]: <-- [9:AT+FTS=7\r] Jul 13 14:20:40.59: [13267]: --> [2:OK] Jul 13 14:20:40.59: [13267]: <-- [10:AT+FTM=24\r] Jul 13 14:20:40.60: [13267]: --> [7:CONNECT] Jul 13 14:20:40.60: [13267]: <-- data [450] Jul 13 14:20:40.60: [13267]: <-- data [2] Jul 13 14:20:43.29: [13267]: --> [2:OK] Jul 13 14:20:43.29: [13267]: <-- [9:AT+FRH=3\r] Jul 13 14:20:46.39: [13267]: --> [0:] Jul 13 14:20:46.39: [13267]: MODEM Jul 13 14:20:46.39: [13267]: <-- data [1] Jul 13 14:20:46.41: [13267]: --> [2:OK] Jul 13 14:20:46.41: [13267]: DELAY 1500 ms Jul 13 14:20:47.91: [13267]: TRAINING failed Jul 13 14:20:47.92: [13267]: <-- [9:AT+FTH=3\r] Jul 13 14:20:47.93: [13267]: --> [7:CONNECT] Jul 13 14:20:47.93: [13267]: <-- data [3] Jul 13 14:20:47.93: [13267]: <-- data [2] Jul 13 14:20:49.21: [13267]: --> [2:OK] Jul 13 14:20:49.21: [13267]: SEND FAILED: JOB 1615 DEST 04-XXXXXXXXXX ERR Failure to train remote modem at 2400 bps or minimum speed; too many attempts to send Jul 13 14:20:49.21: [13267]: <-- [5:ATH0\r] Jul 13 14:20:49.40: [13267]: --> [2:OK] Jul 13 14:20:49.40: [13267]: SESSION END -- Graham Chiu http://www.compkarori.co.nz:8090/ Synapse - the use from anywhere EMR. ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] training failures
- From: Lee Howard
- Re: [hylafax-users] training failures
- Prev by Date: [hylafax-users] T38modem and Hylafax question.
- Next by Date: Re: [hylafax-users] How to find out why email2fax has no PDF attachment?
- Previous by thread: [hylafax-users] T38modem and Hylafax question.
- Next by thread: Re: [hylafax-users] training failures
- Index(es):
Project hosted by iFAX Solutions