Re: [hylafax-users] Here got 3 Sample log file that HylaFAx cannot fax out

[FOO SOON LOKE <fsloke@xxxxxxxxx>]

Question 1:
========
How to configure this ModemHardFlowCmd and
ModemSoftFlowCmd.  And then change ModemFlowControl between "rtscts" and
"xonxoff" in the config.ttyS0?

<<<In conf.ttyS0>>>
ModemHardFlowCmd  "???"
ModemSoftFlowCmd   "???"
ModemFlowControl  "???"

How to change the " DTE-DCE flow control scheme [default]?" between "rtscts" and "xonxoff"?
Is it? You mean this "DTE-DCE flow control scheme [default]? xonxoff" ?

Question 2
========
When the fax can't fax out , the Hylafax fax will attempt to fax again. So far I know default is 3 times retries.
In the configuration, where can I change the retry time interval? Is it possble I want to make it longer? [ I assume that the receiver modem is busy at the time interval that I send out]


Others case:
========
Lee Sir, Got good news. When the document cannot send out first time, I tried second time fax out [ test with the same number], it works. Unfortunely, the second times try I use a test.pdf instead of the original document that fail to fax. So, I cannot verify that it work for the original document.[ I will right back to you soon]. So far that I can tell you is the connection is ok...


Thank Lee...

-fsloke

----- Original Message ----
From: Lee Howard <faxguy@xxxxxxxxxxxxxxxx>
To: FOO SOON LOKE <fsloke@xxxxxxxxx>
Cc: hylafax-users@xxxxxxxxxxx; hylafax-devel@xxxxxxxxxxx
Sent: Tuesday, September 2, 2008 8:40:10 PM
Subject: Re: [hylafax-users] Here got 3 Sample log file that HylaFAx cannot fax out

FOO SOON LOKE wrote:
> Aug 28 10:23:34.93: [ 7716]: SEND send PPS (partial page signal)
> Aug 28 10:23:34.93: [ 7716]: SEND send EOP (no more pages or documents)
> Aug 28 10:23:34.93: [ 7716]: <-- [9:AT+FRH=3\r]
> Aug 28 10:23:35.11: [ 7716]: --> [7:CONNECT]
> Aug 28 10:23:37.23: [ 7716]: --> [2:OK]
> Aug 28 10:23:37.23: [ 7716]: SEND recv PPR (partial page request)
> Aug 28 10:23:37.23: [ 7716]: DELAY 70 ms
> Aug 28 10:23:37.31: [ 7716]: SEND send frame number 60
> Aug 28 10:23:37.31: [ 7716]: SEND send frame number 61
> Aug 28 10:23:37.31: [ 7716]: SEND send frame number 62
> Aug 28 10:23:37.31: [ 7716]: SEND send frame number 63
> Aug 28 10:23:37.31: [ 7716]: SEND send frame number 64

Given that you are consistently needing to re-send frames 60-64 for
every image data block, I would suspect that you're using the wrong flow
control setting for your modem (or that your modem has broken flow control).

Make sure that the following items in your modem config file are
correctly configured for your modem: ModemHardFlowCmd and
ModemSoftFlowCmd.  And then change ModemFlowControl between "rtscts" and
"xonxoff".

Thanks,

Lee.


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxx.*