 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Error When Sending With &D0
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Error When Sending With &D0
- From: "Amir Levin" <amir.levin@xxxxxxxxx>
- Date: Mon, 10 Mar 2008 10:07:03 +0200
I have an external serial modem connecting to a USB port with a pl2303 converter. DTR is not asserted so in order to solve it we need to add &D0 to the init string: ModemResetCmds: AT&D0&W It is dialing but we get an error: Mar 10 09:39:08.83: [23933]: SESSION BEGIN 000026224 97297777777 Mar 10 09:39:08.83: [23933]: HylaFAX (tm) Version 4.3.0 Mar 10 09:39:08.83: [23933]: SEND FAX: JOB 8781 DEST 7777777 COMMID 000026224 DEVICE '/dev/ttyUSB0' FROM Mar 10 09:39:08.83: [23933]: <-- [12:AT+FCLASS=1\r] Mar 10 09:39:08.86: [23933]: --> [2:OK] Mar 10 09:39:08.86: [23933]: DIAL 7777777 Mar 10 09:39:08.86: [23933]: <-- [13:ATDT97777777\r] Mar 10 09:39:27.68: [23933]: --> [7:CONNECT] Mar 10 09:39:27.70: [23933]: --> [2:OK] Mar 10 09:39:27.70: [23933]: REMOTE NSF "AD 00 55 48 79 6C 61 46 41 58 20 28 74 6D 29 20 56 65 72 73 69 6F 6E 20 34 2E 33 2E 30" Mar 10 09:39:27.70: [23933]: NSF remote fax equipment: HylaFAX Mar 10 09:39:27.70: [23933]: NSF remote station ID: "HylaFAX (tm) Version 4.3.0" Mar 10 09:39:27.70: [23933]: <-- [9:AT+FRH=3\r] Mar 10 09:39:28.38: [23933]: --> [7:CONNECT] Mar 10 09:39:28.40: [23933]: --> [2:OK] Mar 10 09:39:28.40: [23933]: REMOTE CSI "**********" Mar 10 09:39:28.40: [23933]: <-- [9:AT+FRH=3\r] Mar 10 09:39:28.82: [23933]: --> [7:CONNECT] Mar 10 09:39:28.83: [23933]: --> [2:OK] Mar 10 09:39:28.83: [23933]: REMOTE best rate 14400 bit/s Mar 10 09:39:28.83: [23933]: REMOTE max A3 page width (303 mm) Mar 10 09:39:28.83: [23933]: REMOTE max unlimited page length Mar 10 09:39:28.83: [23933]: REMOTE best vres R16 x 15.4 line/mm Mar 10 09:39:28.83: [23933]: REMOTE format support: MH, MR, MMR Mar 10 09:39:28.83: [23933]: REMOTE supports T.30 Annex A, 256-byte ECM Mar 10 09:39:28.83: [23933]: REMOTE best 0 ms/scanline Mar 10 09:39:28.83: [23933]: USE 14400 bit/s Mar 10 09:39:28.83: [23933]: USE error correction mode Mar 10 09:39:28.83: [23933]: SEND file "docq/doc8637.ps;c0" Mar 10 09:39:28.83: [23933]: USE A4 page width (215 mm) Mar 10 09:39:28.83: [23933]: USE unlimited page length Mar 10 09:39:28.83: [23933]: USE 3.85 line/mm Mar 10 09:39:28.83: [23933]: USE 2-D MMR Mar 10 09:39:28.83: [23933]: USE 0 ms/scanline Mar 10 09:39:28.83: [23933]: SEND training at v.17 14400 bit/s Mar 10 09:39:28.83: [23933]: <-- [9:AT+FRS=7\r] Mar 10 09:39:28.92: [23933]: --> [2:OK] Mar 10 09:39:28.92: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:39:34.79: [23933]: --> [7:CONNECT] Mar 10 09:39:34.79: [23933]: <-- data [23] Mar 10 09:39:34.79: [23933]: <-- data [2] Mar 10 09:39:34.80: [23933]: --> [5:ERROR] Mar 10 09:39:34.80: [23933]: MODEM Command error Mar 10 09:39:34.80: [23933]: Error sending T.30 prologue frames Mar 10 09:39:34.80: [23933]: SEND training at v.17 12000 bit/s Mar 10 09:39:34.80: [23933]: <-- [9:AT+FRS=7\r] Mar 10 09:39:34.89: [23933]: --> [2:OK] Mar 10 09:39:34.89: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:39:40.76: [23933]: --> [7:CONNECT] Mar 10 09:39:40.76: [23933]: <-- data [23] Mar 10 09:39:40.76: [23933]: <-- data [2] Mar 10 09:39:40.76: [23933]: --> [5:ERROR] Mar 10 09:39:40.76: [23933]: MODEM Command error Mar 10 09:39:40.76: [23933]: Error sending T.30 prologue frames Mar 10 09:39:40.76: [23933]: SEND training at v.17 9600 bit/s Mar 10 09:39:40.76: [23933]: <-- [9:AT+FRS=7\r] Mar 10 09:39:40.86: [23933]: --> [2:OK] Mar 10 09:39:40.86: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:39:46.73: [23933]: --> [7:CONNECT] Mar 10 09:39:46.73: [23933]: <-- data [23] Mar 10 09:39:46.73: [23933]: <-- data [2] Mar 10 09:39:46.74: [23933]: --> [5:ERROR] Mar 10 09:39:46.74: [23933]: MODEM Command error Mar 10 09:39:46.74: [23933]: Error sending T.30 prologue frames Mar 10 09:39:46.74: [23933]: SEND training at v.29 9600 bit/s Mar 10 09:39:46.74: [23933]: <-- [9:AT+FRS=7\r] Mar 10 09:39:46.83: [23933]: --> [2:OK] Mar 10 09:39:46.83: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:39:52.70: [23933]: --> [7:CONNECT] Mar 10 09:39:52.70: [23933]: <-- data [23] Mar 10 09:39:52.70: [23933]: <-- data [2] Mar 10 09:39:52.71: [23933]: --> [5:ERROR] Mar 10 09:39:52.71: [23933]: MODEM Command error Mar 10 09:39:52.71: [23933]: Error sending T.30 prologue frames Mar 10 09:39:52.71: [23933]: SEND training at v.29 7200 bit/s Mar 10 09:39:52.71: [23933]: <-- [9:AT+FRS=7\r] Mar 10 09:39:52.80: [23933]: --> [2:OK] Mar 10 09:39:52.80: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:39:58.67: [23933]: --> [7:CONNECT] Mar 10 09:39:58.67: [23933]: <-- data [23] Mar 10 09:39:58.67: [23933]: <-- data [2] Mar 10 09:39:58.67: [23933]: --> [5:ERROR] Mar 10 09:39:58.67: [23933]: MODEM Command error Mar 10 09:39:58.67: [23933]: Error sending T.30 prologue frames Mar 10 09:39:58.67: [23933]: SEND training at v.27ter 4800 bit/s Mar 10 09:39:58.67: [23933]: <-- [9:AT+FRS=7\r] Mar 10 09:39:58.77: [23933]: --> [2:OK] Mar 10 09:39:58.77: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:40:04.64: [23933]: --> [7:CONNECT] Mar 10 09:40:04.64: [23933]: <-- data [23] Mar 10 09:40:04.64: [23933]: <-- data [2] Mar 10 09:40:04.65: [23933]: --> [5:ERROR] Mar 10 09:40:04.65: [23933]: MODEM Command error Mar 10 09:40:04.65: [23933]: Error sending T.30 prologue frames Mar 10 09:40:04.65: [23933]: SEND training at v.27ter fallback mode 2400 bit/s Mar 10 09:40:04.65: [23933]: <-- [9:AT+FRS=7\r] Mar 10 09:40:04.74: [23933]: --> [2:OK] Mar 10 09:40:04.74: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:40:10.61: [23933]: --> [7:CONNECT] Mar 10 09:40:10.61: [23933]: <-- data [23] Mar 10 09:40:10.61: [23933]: <-- data [2] Mar 10 09:40:10.61: [23933]: --> [5:ERROR] Mar 10 09:40:10.61: [23933]: MODEM Command error Mar 10 09:40:10.61: [23933]: Error sending T.30 prologue frames Mar 10 09:40:10.61: [23933]: TRAINING failed Mar 10 09:40:10.61: [23933]: SEND: Failure to train remote modem at 2400 bps or minimum speed; Giving up Mar 10 09:40:10.61: [23933]: <-- [9:AT+FTH=3\r] Mar 10 09:40:16.50: [23933]: --> [7:CONNECT] Mar 10 09:40:16.50: [23933]: <-- data [3] Mar 10 09:40:16.50: [23933]: <-- data [2] Mar 10 09:40:16.50: [23933]: --> [5:ERROR] Mar 10 09:40:16.50: [23933]: MODEM Command error Mar 10 09:40:16.51: [23933]: <-- [5:ATH0\r] Mar 10 09:40:17.30: [23933]: --> [2:OK] Mar 10 09:40:17.44: [23933]: SESSION END This is the log at the answering machine: Mar 10 09:39:18.77: [23838]: SESSION BEGIN 000026227 97297777777 Mar 10 09:39:18.77: [23838]: HylaFAX (tm) Version 4.3.0 Mar 10 09:39:18.77: [23838]: <-- [4:ATA\r] Mar 10 09:39:26.60: [23838]: --> [7:CONNECT] Mar 10 09:39:26.60: [23838]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0' Mar 10 09:39:26.60: [23838]: RECV FAX: begin Mar 10 09:39:26.60: [23838]: <-- data [32] Mar 10 09:39:26.60: [23838]: <-- data [2] Mar 10 09:39:26.63: [23838]: --> [7:CONNECT] Mar 10 09:39:26.63: [23838]: <-- data [23] Mar 10 09:39:26.63: [23838]: <-- data [2] Mar 10 09:39:26.66: [23838]: --> [7:CONNECT] Mar 10 09:39:26.66: [23838]: <-- data [13] Mar 10 09:39:26.66: [23838]: <-- data [2] Mar 10 09:39:28.86: [23838]: --> [2:OK] Mar 10 09:39:28.86: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:39:28.98: [23838]: --> [7:CONNECT] Mar 10 09:39:34.82: [23838]: --> [10:NO CARRIER] Mar 10 09:39:34.82: [23838]: MODEM No carrier Mar 10 09:39:34.82: [23838]: <-- [9:AT+FRS=7\r] Mar 10 09:39:34.91: [23838]: --> [2:OK] Mar 10 09:39:34.91: [23838]: <-- [9:AT+FTH=3\r] Mar 10 09:39:35.78: [23838]: --> [7:CONNECT] Mar 10 09:39:35.85: [23838]: <-- data [3] Mar 10 09:39:35.85: [23838]: <-- data [2] Mar 10 09:39:36.18: [23838]: --> [2:OK] Mar 10 09:39:36.18: [23838]: RECV send CRP (command repeat) Mar 10 09:39:36.18: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:39:36.24: [23838]: --> [7:CONNECT] Mar 10 09:39:40.79: [23838]: --> [10:NO CARRIER] Mar 10 09:39:40.79: [23838]: MODEM No carrier Mar 10 09:39:40.79: [23838]: <-- [9:AT+FRS=7\r] Mar 10 09:39:40.88: [23838]: --> [2:OK] Mar 10 09:39:40.88: [23838]: <-- [9:AT+FTH=3\r] Mar 10 09:39:41.75: [23838]: --> [7:CONNECT] Mar 10 09:39:41.75: [23838]: <-- data [3] Mar 10 09:39:41.75: [23838]: <-- data [2] Mar 10 09:39:42.07: [23838]: --> [2:OK] Mar 10 09:39:42.07: [23838]: RECV send CRP (command repeat) Mar 10 09:39:42.07: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:39:42.14: [23838]: --> [7:CONNECT] Mar 10 09:39:46.77: [23838]: --> [10:NO CARRIER] Mar 10 09:39:46.77: [23838]: MODEM No carrier Mar 10 09:39:46.77: [23838]: <-- [9:AT+FRS=7\r] Mar 10 09:39:46.86: [23838]: --> [2:OK] Mar 10 09:39:46.86: [23838]: <-- [9:AT+FTH=3\r] Mar 10 09:39:47.73: [23838]: --> [7:CONNECT] Mar 10 09:39:47.73: [23838]: <-- data [3] Mar 10 09:39:47.73: [23838]: <-- data [2] Mar 10 09:39:48.05: [23838]: --> [2:OK] Mar 10 09:39:48.05: [23838]: RECV send CRP (command repeat) Mar 10 09:39:48.05: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:39:48.11: [23838]: --> [7:CONNECT] Mar 10 09:39:52.74: [23838]: --> [10:NO CARRIER] Mar 10 09:39:52.74: [23838]: MODEM No carrier Mar 10 09:39:52.74: [23838]: DELAY 1500 ms Mar 10 09:39:54.24: [23838]: <-- [9:AT+FTH=3\r] Mar 10 09:39:55.11: [23838]: --> [7:CONNECT] Mar 10 09:39:55.11: [23838]: <-- data [32] Mar 10 09:39:55.11: [23838]: <-- data [2] Mar 10 09:39:55.14: [23838]: --> [7:CONNECT] Mar 10 09:39:55.14: [23838]: <-- data [23] Mar 10 09:39:55.14: [23838]: <-- data [2] Mar 10 09:39:55.17: [23838]: --> [7:CONNECT] Mar 10 09:39:55.17: [23838]: <-- data [13] Mar 10 09:39:55.17: [23838]: <-- data [2] Mar 10 09:39:57.37: [23838]: --> [2:OK] Mar 10 09:39:57.37: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:39:57.44: [23838]: --> [7:CONNECT] Mar 10 09:39:58.70: [23838]: --> [10:NO CARRIER] Mar 10 09:39:58.70: [23838]: MODEM No carrier Mar 10 09:39:58.70: [23838]: <-- [9:AT+FRS=7\r] Mar 10 09:39:58.79: [23838]: --> [2:OK] Mar 10 09:39:58.79: [23838]: <-- [9:AT+FTH=3\r] Mar 10 09:39:59.66: [23838]: --> [7:CONNECT] Mar 10 09:39:59.66: [23838]: <-- data [3] Mar 10 09:39:59.66: [23838]: <-- data [2] Mar 10 09:39:59.98: [23838]: --> [2:OK] Mar 10 09:39:59.98: [23838]: RECV send CRP (command repeat) Mar 10 09:39:59.98: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:40:00.05: [23838]: --> [7:CONNECT] Mar 10 09:40:04.68: [23838]: --> [10:NO CARRIER] Mar 10 09:40:04.68: [23838]: MODEM No carrier Mar 10 09:40:04.68: [23838]: <-- [9:AT+FRS=7\r] Mar 10 09:40:04.77: [23838]: --> [2:OK] Mar 10 09:40:04.77: [23838]: <-- [9:AT+FTH=3\r] Mar 10 09:40:05.64: [23838]: --> [7:CONNECT] Mar 10 09:40:05.64: [23838]: <-- data [3] Mar 10 09:40:05.64: [23838]: <-- data [2] Mar 10 09:40:05.96: [23838]: --> [2:OK] Mar 10 09:40:05.96: [23838]: RECV send CRP (command repeat) Mar 10 09:40:05.96: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:40:06.02: [23838]: --> [7:CONNECT] Mar 10 09:40:10.64: [23838]: --> [10:NO CARRIER] Mar 10 09:40:10.64: [23838]: MODEM No carrier Mar 10 09:40:10.64: [23838]: <-- [9:AT+FRS=7\r] Mar 10 09:40:16.64: [23838]: --> [2:OK] Mar 10 09:40:16.64: [23838]: <-- [9:AT+FTH=3\r] Mar 10 09:40:17.51: [23838]: --> [7:CONNECT] Mar 10 09:40:17.51: [23838]: <-- data [3] Mar 10 09:40:17.51: [23838]: <-- data [2] Mar 10 09:40:17.83: [23838]: --> [2:OK] Mar 10 09:40:17.83: [23838]: RECV send CRP (command repeat) Mar 10 09:40:17.83: [23838]: <-- [9:AT+FRH=3\r] Mar 10 09:40:24.84: [23838]: --> [0:] Mar 10 09:40:24.84: [23838]: MODEM <Empty line> Mar 10 09:40:24.84: [23838]: <-- data [1] Mar 10 09:40:24.85: [23838]: --> [2:^P^C] Mar 10 09:40:24.85: [23838]: --> [2:OK] Mar 10 09:40:24.85: [23838]: RECV FAX: No answer (T.30 T1 timeout) Mar 10 09:40:24.85: [23838]: RECV FAX: end Mar 10 09:40:24.85: [23838]: SESSION END The answering modem is working perfectly at the moment, attaching to a serial port. This is the send's modem config: ModemType: Class1 # use this to supply a hint ModemRate: 14400 # rate for DCE-DTE communication ModemDialCmd: ATDT9%s # T for tone dialing ModemResetCmds: AT&D0&W # stuff to do when modem is reset ModemVerboseResultsCmd: ATV1 # enable verbose command results Class1Cmd: AT+FCLASS=1 # command to enter class 1 Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP Class1SendMsgDelay: 200 # 75ms delay after training Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans Class1TrainingRecovery: 1500 # 1.5sec delay after training failure Class1RecvAbortOK: 200 # wait 200ms for abort response Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration Any ideas on how to solve this? Thanks. ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Error When Sending With &D0
- From: Lee Howard
- Re: [hylafax-users] Error When Sending With &D0
- Prev by Date: Re: [hylafax-users] Class 1 is possible to use DDI
- Next by Date: Re: [hylafax-users] missing fax pages
- Previous by thread: Re: [hylafax-users] mgetty problem
- Next by thread: Re: [hylafax-users] Error When Sending With &D0
- Index(es):
Project hosted by iFAX Solutions