 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Courier 990955, outbound & voice
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Courier 990955, outbound & voice
- From: �ž�»�µ�³ �šÑƒÑ€Ñ‡�µ�½�º�¾ <kurchenko.o@xxxxxxxxxx>
- Date: Thu, 06 Mar 2008 18:39:23 +0300
Hi!
Im have courier 990955 with hylafax and i want talk message before send fax:
vgate:/etc/hylafax# cat ./config.ttyS0
# $Id: usr-xon,v 1.11 2005/11/29 21:28:57 lhoward Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
CountryCode: 7 AreaCode: 863 FAXNumber: 0000000 LongDistancePrefix: 9 InternationalPrefix: 9 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "HylaFaxBGS" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 NotifyCmd: bin/notify.php
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
ModemRate: 38400 # max rate for DCE-DTE communication
ModemFlowControl: rtscts # XON/XOFF flow control assumed
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing, @ for silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds: "" # stuff to do when modem is reset
ModemAnswerCmd: ATA # use this to answer phone
ModemNoFlowCmd: AT&H0&I0&R1 # disable flow control cmd
ModemHardFlowCmd: AT&H1&I0&R2 # hardware flow control cmd
ModemSoftFlowCmd: AT&H2&I2&R1 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0 # disable command echo
ModemVerboseResultsCmd: ATV1 # enable verbose command results
ModemResultCodesCmd: ATQ0X4 # enable result codes
ModemOnHookCmd: ATH0 # place phone on hook (hangup)
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FKS # abort session command
# Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2CQQueryCmd: !(0),(0) # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=0
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,0
# Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PIECmd: "" # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control command
ModemDialCmd: "ATS7=50\nAT&K3#CLS=8\nAT#VRN=0#VBT=1\nAT#VSR=11025\nAT#VBS=8\nATDP%s\n<waitfor:VCON>AT#VLS=4\nAT#VTX\n<waitfor:CONNECT><play:1>AT&K4+FCLASS=1\n"
Log file:
vgate:/var/spool/hylafax/log# cat ./c000000081
Мар 06 22:25:05.37: [11063]: SESSION BEGIN 000000081 7863104
Мар 06 22:25:05.37: [11063]: HylaFAX (tm) Version 4.3.1
Мар 06 22:25:05.37: [11063]: SEND FAX: JOB 10 DEST 104 COMMID 000000081 DEVICE '/dev/ttyS0' FROM 'root <root@localhost>' USER admin
Мар 06 22:25:05.37: [11063]: <-- [9:AT+FLO=2\r]
Мар 06 22:25:05.41: [11063]: --> [2:OK]
Мар 06 22:25:05.41: [11063]: <-- [9:AT+FPP=0\r]
Мар 06 22:25:05.46: [11063]: --> [2:OK]
Мар 06 22:25:05.46: [11063]: <-- [9:AT+FBO=0\r]
Мар 06 22:25:05.50: [11063]: --> [2:OK]
Мар 06 22:25:05.50: [11063]: <-- [10:AT+FCT=30\r]
Мар 06 22:25:05.54: [11063]: --> [2:OK]
Мар 06 22:25:05.54: [11063]: <-- [15:AT+FNR=1,1,1,0\r]
Мар 06 22:25:05.58: [11063]: --> [2:OK]
Мар 06 22:25:05.58: [11063]: <-- [9:AT+FIE=0\r]
Мар 06 22:25:05.62: [11063]: --> [2:OK]
Мар 06 22:25:05.62: [11063]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Мар 06 22:25:05.67: [11063]: --> [2:OK]
Мар 06 22:25:05.67: [11063]: DIAL 104
Мар 06 22:25:05.67: [11063]: <-- [8:ATS7=50\r]
Мар 06 22:25:05.84: [11063]: --> [2:OK]
Мар 06 22:25:05.84: [11063]: <-- [12:AT&K3#CLS=8\r]
Мар 06 22:25:06.01: [11063]: --> [5:ERROR]
Мар 06 22:25:06.01: [11063]: MODEM Command error
Мар 06 22:25:06.01: [11063]: SEND FAILED: JOB 10 DEST 104 ERR Unknown problem
Мар 06 22:25:06.01: [11063]: <-- [5:ATH0\r]
Мар 06 22:25:06.18: [11063]: --> [2:OK]
Мар 06 22:25:06.18: [11063]: SESSION END
my modem is not support voice?
____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Courier 990955, outbound & voice
- From: Lee Howard
- Re: [hylafax-users] Courier 990955, outbound & voice
- Prev by Date: Re: [hylafax-users] Multi serial solutions
- Next by Date: Re: [hylafax-users] 911 is being dialed but does not show in any logs
- Previous by thread: Re: [hylafax-users] Multi serial solutions
- Next by thread: Re: [hylafax-users] Courier 990955, outbound & voice
- Index(es):
Project hosted by iFAX Solutions