[hylafax-users] problem with voice

["Belenkov N.K." <n.belenkov@xxxxxxxxxxx>]

Hello!
I have IDC-5614BXL/VR voice modem.
Tryed to setup voice message as was written here http://www.hylafax.org/archive/2006-07/msg00174.php
But i have a problem: modem gone timeout.
Log shows:
------------------------
18:26:07.11: [24478]: SESSION BEGIN 000000010 7812671
18:26:07.11: [24478]: HylaFAX (tm) Version 4.4.0
18:26:07.12: [24478]: SEND FAX: JOB 1 DEST 671 COMMID 000000010 DEVICE '/dev/ttyS0' FROM 'g <n.belenkov@xxxxxxxxxxxxxx>' USER g
18:26:07.12: [24478]: <-- [10:AT+FTBC=0\r]
18:26:07.13: [24478]: --> [2:OK]
18:26:07.13: [24478]: <-- [10:AT+FBOR=0\r]
18:26:07.15: [24478]: --> [2:OK]
18:26:07.15: [24478]: <-- [13:AT+FPHCTO=30\r]
18:26:07.17: [24478]: --> [2:OK]
18:26:07.17: [24478]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
18:26:07.19: [24478]: --> [2:OK]
18:26:07.19: [24478]: DIAL 671
18:26:07.19: [24478]: <-- [8:ATS7=50\r]
18:26:07.21: [24478]: --> [2:OK]
18:26:07.21: [24478]: <-- [12:AT&K3#CLS=8\r]
18:26:07.23: [24478]: --> [2:OK]
18:26:07.23: [24478]: <-- [15:AT#VRN=0#VBT=1\r]
18:26:07.25: [24478]: --> [2:h]
18:26:07.25: [24478]: --> [2:OK]
18:26:07.25: [24478]: <-- [13:AT#VSR=11025\r]
18:26:07.27: [24478]: --> [2:OK]
18:26:07.27: [24478]: <-- [9:AT#VBS=8\r]
18:26:07.29: [24478]: --> [2:OK]
18:26:07.29: [24478]: <-- [8:ATDT671\r]
18:26:11.33: [24478]: --> [4:VCON]
18:26:41.33: [24478]: MODEM <Timeout>
18:26:41.33: [24478]: SEND FAILED: JOB 1 DEST 671 ERR [6] Unknown problem
18:26:42.33: [24478]: <-- [5:ATH0\r]
18:26:43.91: [24478]: --> [2:OK]
18:26:43.91: [24478]: SESSION END
------------------------

Here is cat from config.ttyS0:
--------------
ModemType:              Class2          # use this to supply a hint
#ModemRate:             19200           # max rate for DCE-DTE communication
#ModemFlowControl:      xonxoff         # XON/XOFF flow control assumed
#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
#ModemSetupDCDCmd:      AT&C1           # setup so DCD reflects carrier (or not)
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:          ATDT%s          # T for tone dialing
ModemDialCmd:  
"ATS7=50\nAT&K3#CLS=8\nAT#VRN=0#VBT=1\nAT#VSR=11025\nAT#VBS=8\nATDT%s\n<waitfor:VCON>AT#VLS=4\nAT#VTX\n<waitfor:CONNECT><play:/etc/play1.raw><waitfor:OK>"
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:                ""              # stuff to do when modem is reset
#ModemAnswerCmd:                ATA             # use this to answer phone
#ModemNoFlowCmd:                AT&K            # disable flow control cmd
#ModemHardFlowCmd:      AT&K3           # hardware flow control cmd
#ModemSoftFlowCmd:      AT&K4           # software flow control cmd
#ModemNoAutoAnswerCmd:  ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:     "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:       ATE0            # disable command echo
#ModemVerboseResultsCmd:        ATV1            # enable verbose command results
#ModemResultCodesCmd:   ATQ0            # enable result codes
#ModemOnHookCmd:                ATH0            # place phone on hook (hangup)
#ModemSoftResetCmd:     ATZ             # do soft reset of modem
#ModemSoftResetCmdDelay:        3000    # pause after soft reset
#ModemWaitTimeCmd:      ATS7=60         # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:        ATS8=2          # comma pause time is 2 seconds
#ModemRecvFillOrder:    LSB2MSB         # bit order of received facsimile
#ModemSendFillOrder:    LSB2MSB         # bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd:              AT+FCLASS=2     # command to enter class 2
Class2BORCmd:           AT+FBOR=0       # bit order for phase B/C/D (direct)
Class2RELCmd:           AT+FREL=1       # byte-align EOL codes on recv
Class2CQCmd:            ""              # commands to enable copy quality proc.
Class2AbortCmd:         AT+FK           # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality capabilities
Class2DCCQueryCmd:      AT+FDCC=?       # query for modem capabilities
Class2TBCCmd:           AT+FTBC=0       # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FPHCTO=30    # set phase C timeout parameter
Class2BUGCmd:           AT+FBUG=1       # enable HDLC frame tracing
Class2LIDCmd:           AT+FLID         # set local identifier command
Class2DCCCmd:           AT+FDCC         # set modem capabilities command
Class2DISCmd:           AT+FDIS         # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FCIG         # set polling identifier command
Class2PTSCmd:           AT+FPTS         # set post-page status command
Class2SPLCmd:           AT+FSPL         # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger:  ""              # character sent to modem to start recv
Class2XmitWaitForXON:   yes             # if true, wait for XON before send
--------------

Modem Timed out on <waitfor:VCON>. What's the bug here? Or maybe i'm
doing something wrong?
Thanks.


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*