 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Siemens C55 as a modem
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Siemens C55 as a modem
- From: DI Florian Hackenberger <f.hackenberger@xxxxxxxxx>
- Date: Thu, 17 Jan 2008 20:20:57 +0100
Dear Hylafax users, I'm currently trying to get a Siemens C55 mobile phone working with hylafax. In general I'm able to send faxes, but only to certain destinations. I'm attaching my configuration file for the modem (borrowing the options from [1]), as well as two log files. The c000000019 file is a session with a working destination and the c000000018 is a logfile of a failed session with a different endpoint. Additionally I'm attaching a document, which descibes the AT commands available on the L55 handsets, which is as far as I know the platform on which the C55 is based. I've tried efax as well and it works a bit better, although it still fails sometimes. As a sidenote, I have enabled "virtual flow control" for efax, which made it work in the first place. Could someone please give me some tips how to proceed to get this device to work with hylafax? Cheers, Florian [1] http://www.hylafax.org/archive/2001-01/msg00052.php -- DI Florian Hackenberger eMail: f.hackenberger@xxxxxxxxx
CountryCode: 43 AreaCode: 650 FAXNumber: 00436505050995 LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0660 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: 00436505050995 TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 ModemRate: 19200 # rate for DCE-DTE communication ModemFlowControl: xonxoff # XON/XOFF flow control assumed Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response Class1SendPPMDelay: 75 # 75ms delay before sending PPM Class1SendTCFDelay: 75 # 75ms delay between sending DCS & TCF Class1TrainingRecovery: 1500 # 1.5sec delay after training failure Class1Cmd: AT+FCLASS=1 # command to enter class 1 Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans Class1RecvAbortOK: 200 # wait 200ms for abort response Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration Class1ECMSupport: No
Jan 17 20:03:14.76: [21056]: SESSION BEGIN 000000019 433168145816 Jan 17 20:03:14.76: [21056]: HylaFAX (tm) Version 4.4.0 Jan 17 20:03:14.76: [21056]: SEND FAX: JOB 14 DEST 03168145816 COMMID 000000019 DEVICE '/dev/ttyUSB0' FROM 'office <office@xxxxxxxxxx>' USER office Jan 17 20:03:14.76: [21056]: <-- [12:AT+FCLASS=1\r] Jan 17 20:03:14.80: [21056]: --> [2:OK] Jan 17 20:03:14.80: [21056]: DIAL 03168145816 Jan 17 20:03:14.80: [21056]: <-- [16:ATDT03168145816\r] Jan 17 20:03:33.02: [21056]: --> [7:CONNECT] Jan 17 20:03:34.35: [21056]: --> [5:ERROR] Jan 17 20:03:34.35: [21056]: MODEM Command error Jan 17 20:03:34.35: [21056]: FCS error Jan 17 20:03:34.35: [21056]: <-- [10:AT+FRS=21\r] Jan 17 20:03:36.00: [21056]: --> [2:OK] Jan 17 20:03:36.00: [21056]: <-- [9:AT+FTH=3\r] Jan 17 20:03:36.05: [21056]: --> [7:CONNECT] Jan 17 20:03:36.05: [21056]: <-- data [3] Jan 17 20:03:36.05: [21056]: <-- data [2] Jan 17 20:03:37.27: [21056]: --> [2:OK] Jan 17 20:03:37.27: [21056]: SEND send CRP (command repeat) Jan 17 20:03:37.27: [21056]: <-- [9:AT+FRH=3\r] Jan 17 20:03:38.20: [21056]: --> [7:CONNECT] Jan 17 20:03:39.79: [21056]: --> [2:OK] Jan 17 20:03:39.79: [21056]: REMOTE NSF "20 11 20 00" Jan 17 20:03:39.79: [21056]: NSF remote fax equipment: Dr. Neuhaus Mikroelektronik Jan 17 20:03:39.79: [21056]: <-- [9:AT+FRH=3\r] Jan 17 20:03:39.83: [21056]: --> [7:CONNECT] Jan 17 20:03:40.52: [21056]: --> [2:OK] Jan 17 20:03:40.52: [21056]: REMOTE CSI "+43 316 814581 6" Jan 17 20:03:40.52: [21056]: <-- [9:AT+FRH=3\r] Jan 17 20:03:40.57: [21056]: --> [7:CONNECT] Jan 17 20:03:40.93: [21056]: --> [2:OK] Jan 17 20:03:40.93: [21056]: REMOTE best rate 33600 bit/s Jan 17 20:03:40.93: [21056]: REMOTE max A4 page width (215 mm) Jan 17 20:03:40.93: [21056]: REMOTE max unlimited page length Jan 17 20:03:40.93: [21056]: REMOTE best vres R16 x 15.4 line/mm Jan 17 20:03:40.93: [21056]: REMOTE format support: MH, MR, MMR, JBIG Jan 17 20:03:40.93: [21056]: REMOTE supports T.30 Annex A, 256-byte ECM Jan 17 20:03:40.93: [21056]: REMOTE best 0 ms/scanline Jan 17 20:03:40.93: [21056]: USE 9600 bit/s Jan 17 20:03:40.93: [21056]: SEND file "docq/doc17.tif;70" Jan 17 20:03:40.94: [21056]: USE A4 page width (215 mm) Jan 17 20:03:40.94: [21056]: USE unlimited page length Jan 17 20:03:40.94: [21056]: USE 3.85 line/mm Jan 17 20:03:40.94: [21056]: USE 2-D MR Jan 17 20:03:40.94: [21056]: USE 0 ms/scanline Jan 17 20:03:40.94: [21056]: SEND training at v.29 9600 bit/s Jan 17 20:03:40.94: [21056]: <-- [9:AT+FRS=7\r] Jan 17 20:03:41.06: [21056]: --> [2:OK] Jan 17 20:03:41.06: [21056]: <-- [9:AT+FTH=3\r] Jan 17 20:03:41.11: [21056]: --> [7:CONNECT] Jan 17 20:03:41.11: [21056]: <-- data [23] Jan 17 20:03:41.11: [21056]: <-- data [2] Jan 17 20:03:41.15: [21056]: --> [7:CONNECT] Jan 17 20:03:41.15: [21056]: <-- data [6] Jan 17 20:03:41.15: [21056]: <-- data [2] Jan 17 20:03:43.15: [21056]: --> [2:OK] Jan 17 20:03:43.15: [21056]: <-- [9:AT+FTS=7\r] Jan 17 20:03:43.40: [21056]: --> [2:OK] Jan 17 20:03:43.40: [21056]: <-- [10:AT+FTM=96\r] Jan 17 20:03:43.45: [21056]: --> [7:CONNECT] Jan 17 20:03:43.45: [21056]: <-- data [1024] Jan 17 20:03:43.88: [21056]: <-- data [776] Jan 17 20:03:44.32: [21056]: <-- data [2] Jan 17 20:03:45.22: [21056]: --> [2:OK] Jan 17 20:03:45.22: [21056]: <-- [9:AT+FRH=3\r] Jan 17 20:03:45.92: [21056]: --> [7:CONNECT] Jan 17 20:03:47.17: [21056]: --> [2:OK] Jan 17 20:03:47.17: [21056]: TRAINING succeeded Jan 17 20:03:47.17: [21056]: <-- [9:AT+FRS=7\r] Jan 17 20:03:47.28: [21056]: --> [2:OK] Jan 17 20:03:47.28: [21056]: <-- [10:AT+FTM=96\r] Jan 17 20:03:47.33: [21056]: --> [7:CONNECT] Jan 17 20:03:47.33: [21056]: SEND begin page Jan 17 20:03:47.33: [21056]: <-- data [1028] Jan 17 20:03:47.80: [21056]: <-- data [1030] Jan 17 20:03:48.33: [21056]: <-- data [1028] Jan 17 20:03:48.87: [21056]: <-- data [1024] Jan 17 20:03:49.37: [21056]: <-- data [1025] Jan 17 20:03:49.93: [21056]: <-- data [1030] Jan 17 20:03:50.47: [21056]: <-- data [1032] Jan 17 20:03:51.00: [21056]: <-- data [1027] Jan 17 20:03:51.54: [21056]: <-- data [1030] Jan 17 20:03:52.07: [21056]: <-- data [1024] Jan 17 20:03:52.57: [21056]: <-- data [1034] Jan 17 20:03:53.14: [21056]: <-- data [1024] Jan 17 20:03:53.64: [21056]: <-- data [1027] Jan 17 20:03:54.21: [21056]: <-- data [1026] Jan 17 20:03:54.74: [21056]: <-- data [1035] Jan 17 20:03:55.28: [21056]: <-- data [1036] Jan 17 20:03:55.81: [21056]: <-- data [1028] Jan 17 20:03:56.35: [21056]: <-- data [1031] Jan 17 20:03:56.89: [21056]: <-- data [1031] Jan 17 20:03:57.42: [21056]: <-- data [1032] Jan 17 20:03:57.96: [21056]: <-- data [1029] Jan 17 20:03:58.50: [21056]: <-- data [1026] Jan 17 20:03:59.03: [21056]: <-- data [1025] Jan 17 20:03:59.56: [21056]: <-- data [1032] Jan 17 20:04:00.10: [21056]: <-- data [1036] Jan 17 20:04:00.63: [21056]: <-- data [1034] Jan 17 20:04:01.17: [21056]: <-- data [1035] Jan 17 20:04:01.71: [21056]: <-- data [1031] Jan 17 20:04:02.25: [21056]: <-- data [1031] Jan 17 20:04:02.78: [21056]: <-- data [1028] Jan 17 20:04:03.32: [21056]: <-- data [1028] Jan 17 20:04:03.85: [21056]: <-- data [1034] Jan 17 20:04:04.39: [21056]: <-- data [1026] Jan 17 20:04:04.92: [21056]: <-- data [1030] Jan 17 20:04:05.46: [21056]: <-- data [1025] Jan 17 20:04:05.99: [21056]: <-- data [1028] Jan 17 20:04:06.53: [21056]: <-- data [1028] Jan 17 20:04:07.06: [21056]: <-- data [1029] Jan 17 20:04:07.60: [21056]: <-- data [1032] Jan 17 20:04:08.13: [21056]: <-- data [1026] Jan 17 20:04:08.67: [21056]: <-- data [1030] Jan 17 20:04:09.20: [21056]: <-- data [1026] Jan 17 20:04:09.74: [21056]: <-- data [1030] Jan 17 20:04:10.27: [21056]: <-- data [1026] Jan 17 20:04:10.80: [21056]: <-- data [1029] Jan 17 20:04:11.34: [21056]: <-- data [1029] Jan 17 20:04:11.87: [21056]: <-- data [1025] Jan 17 20:04:12.41: [21056]: <-- data [1025] Jan 17 20:04:12.94: [21056]: <-- data [1024] Jan 17 20:04:13.44: [21056]: <-- data [1024] Jan 17 20:04:13.97: [21056]: <-- data [759] Jan 17 20:04:14.37: [21056]: SENT 51959 bytes of data Jan 17 20:04:14.37: [21056]: SEND 2D RTC Jan 17 20:04:14.37: [21056]: <-- data [30] Jan 17 20:04:14.40: [21056]: <-- data [2] Jan 17 20:04:14.44: [21056]: SEND end page Jan 17 20:04:16.48: [21056]: --> [2:OK] Jan 17 20:04:16.48: [21056]: <-- [9:AT+FTS=9\r] Jan 17 20:04:16.81: [21056]: --> [2:OK] Jan 17 20:04:16.81: [21056]: SEND send EOP (no more pages or documents) Jan 17 20:04:16.81: [21056]: <-- [9:AT+FTH=3\r] Jan 17 20:04:16.85: [21056]: --> [7:CONNECT] Jan 17 20:04:16.85: [21056]: <-- data [3] Jan 17 20:04:16.85: [21056]: <-- data [2] Jan 17 20:04:18.07: [21056]: --> [2:OK] Jan 17 20:04:18.07: [21056]: <-- [9:AT+FRH=3\r] Jan 17 20:04:18.94: [21056]: --> [7:CONNECT] Jan 17 20:04:20.19: [21056]: --> [2:OK] Jan 17 20:04:20.19: [21056]: SEND recv RTP (retrain positive) Jan 17 20:04:20.19: [21056]: SEND FAX (000000019): FROM office@xxxxxxxxxx TO 03168145816 (page 1 of 1 sent in 0:40) Jan 17 20:04:20.19: [21056]: <-- [9:AT+FRS=7\r] Jan 17 20:04:20.30: [21056]: --> [2:OK] Jan 17 20:04:20.30: [21056]: SEND FAX (000000019): FROM office@xxxxxxxxxx TO 03168145816 (docq/doc17.tif;70 sent in 0:40) Jan 17 20:04:21.19: [21056]: <-- [9:AT+FTH=3\r] Jan 17 20:04:21.23: [21056]: --> [7:CONNECT] Jan 17 20:04:21.23: [21056]: <-- data [3] Jan 17 20:04:21.23: [21056]: <-- data [2] Jan 17 20:04:22.45: [21056]: --> [2:OK] Jan 17 20:04:23.46: [21056]: <-- [5:ATH0\r] Jan 17 20:04:23.74: [21056]: --> [2:OK] Jan 17 20:04:23.75: [21056]: SESSION END
Jan 17 19:50:33.00: [19283]: SESSION BEGIN 000000018 4331632200735 Jan 17 19:50:33.00: [19283]: HylaFAX (tm) Version 4.4.0 Jan 17 19:50:33.00: [19283]: SEND FAX: JOB 13 DEST 031632200735 COMMID 000000018 DEVICE '/dev/ttyUSB0' FROM 'office <office@xxxxxxxxxx>' USER office Jan 17 19:50:33.00: [19283]: <-- [12:AT+FCLASS=1\r] Jan 17 19:50:33.03: [19283]: --> [2:OK] Jan 17 19:50:33.03: [19283]: DIAL 031632200735 Jan 17 19:50:33.03: [19283]: <-- [17:ATDT031632200735\r] Jan 17 19:50:52.19: [19283]: --> [7:CONNECT] Jan 17 19:50:53.55: [19283]: --> [2:OK] Jan 17 19:50:53.55: [19283]: REMOTE NSF "20 11 20 00" Jan 17 19:50:53.55: [19283]: NSF remote fax equipment: Dr. Neuhaus Mikroelektronik Jan 17 19:50:53.55: [19283]: <-- [9:AT+FRH=3\r] Jan 17 19:50:53.59: [19283]: --> [7:CONNECT] Jan 17 19:50:54.28: [19283]: --> [2:OK] Jan 17 19:50:54.28: [19283]: REMOTE CSI "" Jan 17 19:50:54.28: [19283]: <-- [9:AT+FRH=3\r] Jan 17 19:50:54.33: [19283]: --> [7:CONNECT] Jan 17 19:50:54.57: [19283]: --> [2:OK] Jan 17 19:50:54.57: [19283]: REMOTE best rate 9600 bit/s Jan 17 19:50:54.57: [19283]: REMOTE max A4 page width (215 mm) Jan 17 19:50:54.57: [19283]: REMOTE max unlimited page length Jan 17 19:50:54.57: [19283]: REMOTE best vres 7.7 line/mm Jan 17 19:50:54.57: [19283]: REMOTE format support: MH, MR Jan 17 19:50:54.57: [19283]: REMOTE best 20 ms, 10 ms/scanline Jan 17 19:50:54.57: [19283]: USE 9600 bit/s Jan 17 19:50:54.57: [19283]: SEND file "docq/doc16.tif;70" Jan 17 19:50:54.57: [19283]: USE A4 page width (215 mm) Jan 17 19:50:54.57: [19283]: USE unlimited page length Jan 17 19:50:54.57: [19283]: USE 3.85 line/mm Jan 17 19:50:54.57: [19283]: USE 2-D MR Jan 17 19:50:54.57: [19283]: USE 20 ms/scanline Jan 17 19:50:54.57: [19283]: SEND training at v.29 9600 bit/s Jan 17 19:50:54.57: [19283]: <-- [9:AT+FRS=7\r] Jan 17 19:50:54.72: [19283]: --> [2:OK] Jan 17 19:50:54.72: [19283]: <-- [9:AT+FTH=3\r] Jan 17 19:50:54.75: [19283]: --> [7:CONNECT] Jan 17 19:50:54.75: [19283]: <-- data [23] Jan 17 19:50:54.75: [19283]: <-- data [2] Jan 17 19:50:54.79: [19283]: --> [7:CONNECT] Jan 17 19:50:54.79: [19283]: <-- data [6] Jan 17 19:50:54.79: [19283]: <-- data [2] Jan 17 19:50:56.79: [19283]: --> [2:OK] Jan 17 19:50:56.79: [19283]: <-- [9:AT+FTS=7\r] Jan 17 19:50:57.05: [19283]: --> [2:OK] Jan 17 19:50:57.05: [19283]: <-- [10:AT+FTM=96\r] Jan 17 19:50:57.09: [19283]: --> [7:CONNECT] Jan 17 19:50:57.09: [19283]: <-- data [1024] Jan 17 19:50:57.53: [19283]: <-- data [776] Jan 17 19:50:57.96: [19283]: <-- data [2] Jan 17 19:50:58.87: [19283]: --> [2:OK] Jan 17 19:50:58.87: [19283]: <-- [9:AT+FRH=3\r] Jan 17 19:50:59.83: [19283]: --> [7:CONNECT] Jan 17 19:51:01.03: [19283]: --> [2:OK] Jan 17 19:51:01.03: [19283]: TRAINING succeeded Jan 17 19:51:01.03: [19283]: <-- [9:AT+FRS=7\r] Jan 17 19:51:01.18: [19283]: --> [2:OK] Jan 17 19:51:01.18: [19283]: <-- [10:AT+FTM=96\r] Jan 17 19:51:01.23: [19283]: --> [7:CONNECT] Jan 17 19:51:01.23: [19283]: SEND begin page Jan 17 19:51:01.23: [19283]: <-- data [1029] Jan 17 19:51:01.70: [19283]: <-- data [1030] Jan 17 19:51:02.23: [19283]: <-- data [1026] Jan 17 19:51:02.77: [19283]: <-- data [1026] Jan 17 19:51:03.30: [19283]: <-- data [1024] Jan 17 19:51:03.80: [19283]: <-- data [1024] Jan 17 19:51:04.34: [19283]: <-- data [1030] Jan 17 19:51:04.90: [19283]: <-- data [1029] Jan 17 19:51:05.44: [19283]: <-- data [1030] Jan 17 19:51:05.97: [19283]: <-- data [1025] Jan 17 19:51:06.51: [19283]: <-- data [1030] Jan 17 19:51:07.04: [19283]: <-- data [1024] Jan 17 19:51:07.54: [19283]: <-- data [1031] Jan 17 19:51:08.11: [19283]: <-- data [1027] Jan 17 19:51:08.64: [19283]: <-- data [1024] Jan 17 19:51:09.14: [19283]: <-- data [1027] Jan 17 19:51:09.71: [19283]: <-- data [1024] Jan 17 19:51:10.21: [19283]: <-- data [1037] Jan 17 19:51:10.78: [19283]: <-- data [1036] Jan 17 19:51:11.31: [19283]: <-- data [1024] Jan 17 19:51:11.82: [19283]: <-- data [1033] Jan 17 19:51:12.39: [19283]: <-- data [1026] Jan 17 19:51:12.92: [19283]: <-- data [1034] Jan 17 19:51:13.46: [19283]: <-- data [1032] Jan 17 19:51:13.99: [19283]: <-- data [1026] Jan 17 19:51:14.53: [19283]: <-- data [219] Jan 17 19:51:14.63: [19283]: SENT 25817 bytes of data Jan 17 19:51:14.63: [19283]: <-- data [1024] Jan 17 19:51:15.14: [19283]: <-- data [1024] Jan 17 19:51:15.68: [19283]: <-- data [1028] Jan 17 19:51:16.24: [19283]: <-- data [1039] Jan 17 19:51:16.78: [19283]: <-- data [1031] Jan 17 19:51:17.32: [19283]: <-- data [1034] Jan 17 19:51:17.85: [19283]: <-- data [1034] Jan 17 19:51:18.39: [19283]: <-- data [1032] Jan 17 19:51:18.93: [19283]: <-- data [1030] Jan 17 19:51:19.46: [19283]: <-- data [1024] Jan 17 19:51:19.97: [19283]: <-- data [1033] Jan 17 19:51:20.53: [19283]: <-- data [1029] Jan 17 19:51:21.07: [19283]: <-- data [1025] Jan 17 19:51:21.60: [19283]: <-- data [1028] Jan 17 19:51:22.14: [19283]: <-- data [1027] Jan 17 19:51:22.67: [19283]: <-- data [1028] Jan 17 19:51:23.20: [19283]: <-- data [1025] Jan 17 19:51:23.74: [19283]: <-- data [1027] Jan 17 19:51:24.27: [19283]: <-- data [1029] Jan 17 19:51:24.80: [19283]: <-- data [1029] Jan 17 19:51:25.34: [19283]: <-- data [1028] Jan 17 19:51:25.87: [19283]: <-- data [1026] Jan 17 19:51:26.41: [19283]: <-- data [1030] Jan 17 19:51:26.94: [19283]: <-- data [1026] Jan 17 19:51:27.48: [19283]: <-- data [1026] Jan 17 19:51:28.01: [19283]: <-- data [141] Jan 17 19:51:28.08: [19283]: SENT 25739 bytes of data Jan 17 19:51:28.08: [19283]: <-- data [1026] Jan 17 19:51:28.62: [19283]: <-- data [1027] Jan 17 19:51:29.15: [19283]: <-- data [1029] Jan 17 19:51:29.68: [19283]: <-- data [1028] Jan 17 19:51:30.22: [19283]: <-- data [1025] Jan 17 19:51:30.75: [19283]: <-- data [1024] Jan 17 19:51:31.25: [19283]: <-- data [1025] Jan 17 19:51:31.82: [19283]: <-- data [1024] Jan 17 19:51:32.32: [19283]: <-- data [1024] Jan 17 19:51:32.85: [19283]: <-- data [1024] Jan 17 19:51:33.38: [19283]: <-- data [822] Jan 17 19:51:33.82: [19283]: SENT 11062 bytes of data Jan 17 19:51:33.82: [19283]: SEND 2D RTC Jan 17 19:51:33.82: [19283]: <-- data [30] Jan 17 19:51:33.85: [19283]: <-- data [2] Jan 17 19:51:33.88: [19283]: SEND end page Jan 17 19:51:48.87: [19283]: --> [10:NO CARRIER] Jan 17 19:51:48.87: [19283]: Unspecified Transmit Phase C error Jan 17 19:51:48.87: [19283]: <-- [9:AT+FRS=7\r] Jan 17 19:51:49.01: [19283]: --> [2:OK] Jan 17 19:51:49.01: [19283]: <-- [9:AT+FTH=3\r] Jan 17 19:51:49.06: [19283]: --> [5:ERROR] Jan 17 19:51:50.06: [19283]: <-- [5:ATH0\r] Jan 17 19:51:50.21: [19283]: --> [2:OK] Jan 17 19:51:50.22: [19283]: SESSION END
Attachment:
ATC_Command_Set_For_L55_Platform.pdf
Description: Adobe PDF document
- Follow-Ups:
- Re: [hylafax-users] Siemens C55 as a modem
- From: Lee Howard
- Re: [hylafax-users] Siemens C55 as a modem
- Prev by Date: Re: [hylafax-users] Client For Windows Vista
- Next by Date: Re: [hylafax-users] FaxMail + PDF Attachments + Email Header
- Previous by thread: Re: [hylafax-users] MT modem hangs OH and TR stays on forever
- Next by thread: Re: [hylafax-users] Siemens C55 as a modem
- Index(es):
Project hosted by iFAX Solutions