Re: [hylafax-users] wierd faxes..

To: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] wierd faxes..
From: Shawn Henderson <shawn@xxxxxxxxxxxx>
Reply-to: shawn@xxxxxxxxxxxx
Date: Tue, 30 Oct 2007 22:13:11 -0400

I have pasted two logs below I notice that one is longer than the other .. not sure if it makes a difference..

Here is a fax that has the problem...

Oct 30 09:20:35.13: [28960]: SESSION BEGIN 000000103 +17247742116
Oct 30 09:20:35.13: [28960]: HylaFAX (tm) Version 5.1.10
Oct 30 09:20:35.13: [28960]: CallID: '6106502300' '' '<NONE>' '2116'
Oct 30 09:20:35.13: [28960]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Oct 30 09:20:35.13: [28960]: <-- [4:ATA\r]
Oct 30 09:20:38.85: [28960]: --> [7:CONNECT]
Oct 30 09:20:38.85: [28960]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyIAX0'
Oct 30 09:20:38.85: [28960]: STATE CHANGE: ANSWERING -> RECEIVING
Oct 30 09:20:38.85: [28960]: RECV FAX: begin
Oct 30 09:20:38.85: [28960]: <-- HDLC<33:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 AC 74 8C 74 8C 0C>
Oct 30 09:20:39.81: [28960]: --> [7:CONNECT]
Oct 30 09:20:39.81: [28960]: <-- HDLC<23:FF C0 02 0C B6 A6 26 F6 B6 1A 82 92 04 04 04 04 04 04 04 04 04 04 04>
Oct 30 09:20:40.55: [28960]: --> [7:CONNECT]
Oct 30 09:20:40.55: [28960]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>
Oct 30 09:20:41.13: [28960]: --> [2:OK]
Oct 30 09:20:41.13: [28960]: <-- [9:AT+FRH=3\r]
Oct 30 09:20:41.76: [28960]: --> [7:CONNECT]
Oct 30 09:20:42.88: [28960]: --> HDLC<9:FF C8 C1 00 66 1F 00 BB 5D>
Oct 30 09:20:42.92: [28960]: --> [2:OK]
Oct 30 09:20:42.92: [28960]: RECV recv DCS (command signal)
Oct 30 09:20:42.92: [28960]: REMOTE wants 9600 bit/s
Oct 30 09:20:42.92: [28960]: REMOTE wants A4 page width (215 mm)
Oct 30 09:20:42.92: [28960]: REMOTE wants unlimited page length
Oct 30 09:20:42.92: [28960]: REMOTE wants 7.7 line/mm
Oct 30 09:20:42.92: [28960]: REMOTE wants 1-D MH
Oct 30 09:20:42.92: [28960]: RECV training at v.17 9600 bit/s
Oct 30 09:20:42.92: [28960]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Oct 30 09:20:42.92: [28960]: <-- [10:AT+FRM=97\r]
Oct 30 09:20:44.56: [28960]: --> [7:CONNECT]
Oct 30 09:20:45.98: [28960]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Oct 30 09:20:45.98: [28960]: RECV: TCF 1699 bytes, 0% non-zero, 1684 zero-run
Oct 30 09:20:45.98: [28960]: --> [10:NO CARRIER]
Oct 30 09:20:45.98: [28960]: <-- [9:AT+FRS=7\r]
Oct 30 09:20:46.04: [28960]: --> [2:OK]
Oct 30 09:20:46.04: [28960]: TRAINING succeeded
Oct 30 09:20:46.04: [28960]: <-- [9:AT+FTH=3\r]
Oct 30 09:20:46.05: [28960]: --> [7:CONNECT]
Oct 30 09:20:46.05: [28960]: <-- HDLC<3:FF C8 21>
Oct 30 09:20:47.13: [28960]: --> [2:OK]
Oct 30 09:20:47.13: [28960]: <-- [10:AT+FRM=98\r]
Oct 30 09:20:48.42: [28960]: --> [7:CONNECT]
Oct 30 09:20:48.42: [28960]: MODEM input buffering enabled
Oct 30 09:20:48.42: [28960]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Oct 30 09:20:48.42: [28960]: RECV: begin page
Oct 30 09:20:52.58: [28960]: RECV/CQ: Bad 1D pixel count, row 192, got 3320, expected 1728
Oct 30 09:20:54.23: [28960]: RECV/CQ: Bad 1D pixel count, row 227, got 2825, expected 1728
Oct 30 09:20:55.06: [28960]: RECV/CQ: Bad 1D pixel count, row 228, got 3468, expected 1728
Oct 30 09:20:56.94: [28960]: RECV/CQ: Bad 1D pixel count, row 229, got 2208, expected 1728
Oct 30 09:20:56.94: [28960]: RECV/CQ: Bad 1D pixel count, row 230, got 1814, expected 1728
Oct 30 09:20:57.76: [28960]: RECV/CQ: Bad 1D pixel count, row 231, got 2634, expected 1728
Oct 30 09:20:57.98: [28960]: RECV/CQ: Bad 1D pixel count, row 232, got 2074, expected 1728
Oct 30 09:20:59.02: [28960]: RECV/CQ: Invalid WhiteTable code word, row 233, x 1184
Oct 30 09:20:59.02: [28960]: RECV/CQ: Bad 1D pixel count, row 233, got 1184, expected 1728
Oct 30 09:20:59.22: [28960]: RECV/CQ: Bad 1D pixel count, row 234, got 2071, expected 1728
Oct 30 09:20:59.84: [28960]: RECV/CQ: Bad 1D pixel count, row 235, got 2035, expected 1728
Oct 30 09:20:59.84: [28960]: RECV/CQ: Bad 1D pixel count, row 236, got 1981, expected 1728
Oct 30 09:21:01.50: [28960]: RECV/CQ: Bad 1D pixel count, row 237, got 2073, expected 1728
Oct 30 09:21:01.92: [28960]: RECV/CQ: Bad 1D pixel count, row 238, got 2244, expected 1728
Oct 30 09:21:03.36: [28960]: RECV/CQ: Bad 1D pixel count, row 239, got 1916, expected 1728
Oct 30 09:21:05.24: [28960]: RECV/CQ: Bad 1D pixel count, row 241, got 1861, expected 1728
Oct 30 09:21:05.64: [28960]: RECV/CQ: Bad 1D pixel count, row 242, got 2624, expected 1728
Oct 30 09:21:06.26: [28960]: RECV/CQ: Bad 1D pixel count, row 243, got 1792, expected 1728
Oct 30 09:21:07.52: [28960]: RECV/CQ: Bad 1D pixel count, row 244, got 1864, expected 1728
Oct 30 09:21:07.72: [28960]: RECV/CQ: Bad 1D pixel count, row 245, got 2317, expected 1728
Oct 30 09:21:21.88: [28960]: RECV/CQ: Bad 1D pixel count, row 983, got 1767, expected 1728
Oct 30 09:21:22.08: [28960]: RECV/CQ: Bad 1D pixel count, row 984, got 3280, expected 1728
Oct 30 09:21:33.08: [28960]: RECV/CQ: Bad 1D pixel count, row 2031, got 0, expected 1728
Oct 30 09:21:33.08: [28960]: RECV/CQ: Bad 1D pixel count, row 2032, got 0, expected 1728
Oct 30 09:21:33.08: [28960]: RECV/CQ: Bad 1D pixel count, row 2033, got 0, expected 1728
Oct 30 09:21:33.08: [28960]: RECV/CQ: Bad 1D pixel count, row 2034, got 0, expected 1728
Oct 30 09:21:33.08: [28960]: RECV/CQ: Adjusting for RTC found at row 2031
Oct 30 09:21:33.08: [28960]: RECV: 2031 total lines, 21 bad lines, 13 consecutive bad lines
Oct 30 09:21:33.08: [28960]: RECV: REJECT page quality, 13-line run (max 10)
Oct 30 09:21:33.08: [28960]: RECV: end page
Oct 30 09:21:33.08: [28960]: --> [10:NO CARRIER]
Oct 30 09:21:33.08: [28960]: <-- [9:AT+FRH=3\r]
Oct 30 09:21:33.34: [28960]: --> [7:CONNECT]
Oct 30 09:21:34.38: [28960]: --> HDLC<5:FF C8 F2 AC A0>
Oct 30 09:21:34.38: [28960]: --> [2:OK]
Oct 30 09:21:34.38: [28960]: RECV recv MPS (more pages, same document)
Oct 30 09:21:34.38: [28960]: <-- [9:AT+FRS=7\r]
Oct 30 09:21:34.48: [28960]: --> [2:OK]
Oct 30 09:21:34.48: [28960]: RECV send RTN (retrain negative)
Oct 30 09:21:34.48: [28960]: <-- [9:AT+FTH=3\r]
Oct 30 09:21:34.59: [28960]: --> [7:CONNECT]
Oct 30 09:21:34.59: [28960]: RECV FAX (000000103): from <UNSPECIFIED>, page 1 in 0:55, INF, 7.7 line/mm, 1-D MH, 9600 bit/s
Oct 30 09:21:34.59: [28960]: <-- HDLC<3:FF C8 32>
Oct 30 09:21:35.67: [28960]: --> [2:OK]
Oct 30 09:21:35.67: [28960]: <-- [9:AT+FRH=3\r]
Oct 30 09:21:36.16: [28960]: --> [7:CONNECT]
Oct 30 09:21:37.16: [28960]: --> HDLC<5:FF C8 DF 59 6F>
Oct 30 09:21:37.16: [28960]: --> [2:OK]
Oct 30 09:21:37.16: [28960]: RECV recv DCN (disconnect)
Oct 30 09:21:37.16: [28960]: RECV FAX (000000103): recvq/fax000000031.tif from <UNSPECIFIED>, subaddress <unspecified>, 1 pages in 0:59
Oct 30 09:21:37.16: [28960]: RECV FAX: RSPREC error/got DCN (sender abort) {E103}
Oct 30 09:21:37.16: [28960]: RECV FAX (000000103): session with <UNSPECIFIED> terminated abnormally: RSPREC error/got DCN (sender abort) {E103}
Oct 30 09:21:37.16: [28960]: RECV FAX: bin/faxrcvd 'recvq/fax000000031.tif' 'ttyIAX0' '000000103' 'RSPREC error/got DCN (sender abort) {E103}' '6106502300' '' '<NONE>' '2116'
Oct 30 09:21:37.16: [28960]: RECV FAX: end
Oct 30 09:21:37.16: [28960]: SESSION END

Here is one that does not...

Oct 30 10:25:55.48: [20377]: SESSION BEGIN 000000110 +17247742116 Oct 30 10:25:55.48: [20377]: HylaFAX (tm) Version 5.1.10 Oct 30 10:25:55.48: [20377]: CallID: '' '' '<NONE>' '2116' Oct 30 10:25:55.48: [20377]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled Oct 30 10:25:55.48: [20377]: <-- [4:ATA\r] Oct 30 10:25:59.20: [20377]: --> [7:CONNECT] Oct 30 10:25:59.20: [20377]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyIAX0' Oct 30 10:25:59.20: [20377]: STATE CHANGE: ANSWERING -> RECEIVING Oct 30 10:25:59.20: [20377]: RECV FAX: begin Oct 30 10:25:59.20: [20377]: <-- HDLC<33:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 AC 74 8C 74 8C 0C> Oct 30 10:25:59.20: [20377]: <-- data [33] Oct 30 10:25:59.20: [20377]: <-- data [2] Oct 30 10:26:00.16: [20377]: --> [7:CONNECT] Oct 30 10:26:00.16: [20377]: <-- HDLC<23:FF C0 02 0C B6 A6 26 F6 B6 1A 82 92 04 04 04 04 04 04 04 04 04 04 04> Oct 30 10:26:00.16: [20377]: <-- data [23] Oct 30 10:26:00.16: [20377]: <-- data [2] Oct 30 10:26:00.90: [20377]: --> [7:CONNECT] Oct 30 10:26:00.90: [20377]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18> Oct 30 10:26:00.90: [20377]: <-- data [13] Oct 30 10:26:00.90: [20377]: <-- data [2] Oct 30 10:26:01.48: [20377]: --> [2:OK] Oct 30 10:26:01.48: [20377]: <-- [9:AT+FRH=3\r] Oct 30 10:26:01.77: [20377]: --> [7:CONNECT] Oct 30 10:26:03.36: [20377]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 1E 86 62 04 86 96 6A 60 BE> Oct 30 10:26:03.36: [20377]: --> [2:OK] Oct 30 10:26:03.36: [20377]: RECV recv TSI (sender id) Oct 30 10:26:03.36: [20377]: REMOTE TSI "Via Fax" Oct 30 10:26:03.36: [20377]: <-- [9:AT+FRH=3\r] Oct 30 10:26:03.66: [20377]: --> [7:CONNECT] Oct 30 10:26:03.66: [20377]: --> HDLC<9:FF C8 C1 00 44 1F 22 57 DB> Oct 30 10:26:03.76: [20377]: --> [2:OK] Oct 30 10:26:03.76: [20377]: RECV recv DCS (command signal) Oct 30 10:26:03.76: [20377]: REMOTE wants 14400 bit/s Oct 30 10:26:03.76: [20377]: REMOTE wants A4 page width (215 mm) Oct 30 10:26:03.76: [20377]: REMOTE wants unlimited page length Oct 30 10:26:03.76: [20377]: REMOTE wants 3.85 line/mm Oct 30 10:26:03.76: [20377]: REMOTE wants 2-D MMR Oct 30 10:26:03.76: [20377]: REMOTE wants T.30 Annex A, 256-byte ECM Oct 30 10:26:03.76: [20377]: RECV training at v.17 14400 bit/s Oct 30 10:26:03.76: [20377]: MODEM set XON/XOFF/DRAIN: input ignored, output generated Oct 30 10:26:03.76: [20377]: <-- [11:AT+FRM=145\r] Oct 30 10:26:05.46: [20377]: --> [7:CONNECT] Oct 30 10:26:06.99: [20377]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled Oct 30 10:26:06.99: [20377]: RECV: TCF 2747 bytes, 1% non-zero, 2707 zero-run Oct 30 10:26:06.99: [20377]: --> [10:NO CARRIER] Oct 30 10:26:06.99: [20377]: <-- [9:AT+FRS=7\r] Oct 30 10:26:07.04: [20377]: --> [2:OK] Oct 30 10:26:07.05: [20377]: TRAINING succeeded Oct 30 10:26:07.05: [20377]: <-- [9:AT+FTH=3\r] Oct 30 10:26:07.06: [20377]: --> [7:CONNECT] Oct 30 10:26:07.06: [20377]: <-- HDLC<3:FF C8 21> Oct 30 10:26:07.06: [20377]: <-- data [3] Oct 30 10:26:07.06: [20377]: <-- data [2] Oct 30 10:26:08.14: [20377]: --> [2:OK] Oct 30 10:26:08.14: [20377]: <-- [11:AT+FRM=146\r] Oct 30 10:26:09.28: [20377]: --> [7:CONNECT] Oct 30 10:26:09.28: [20377]: MODEM input buffering enabled Oct 30 10:26:09.28: [20377]: MODEM set XON/XOFF/FLUSH: input ignored, output generated Oct 30 10:26:09.69: [20377]: RECV received frame number 0 Oct 30 10:26:09.69: [20377]: RECV received frame number 0 Oct 30 10:26:09.83: [20377]: RECV received frame number 1 Oct 30 10:26:09.97: [20377]: RECV received frame number 2 Oct 30 10:26:10.11: [20377]: RECV received frame number 3 Oct 30 10:26:10.23: [20377]: RECV received frame number 4 Oct 30 10:26:10.50: [20377]: RECV received frame number 5 Oct 30 10:26:10.64: [20377]: RECV received frame number 6 Oct 30 10:26:10.79: [20377]: RECV received frame number 7 Oct 30 10:26:10.93: [20377]: RECV received frame number 8 Oct 30 10:26:11.07: [20377]: RECV received frame number 9 Oct 30 10:26:11.21: [20377]: RECV received frame number 10 Oct 30 10:26:11.33: [20377]: RECV received frame number 11 Oct 30 10:26:11.47: [20377]: RECV received frame number 12 Oct 30 10:26:11.61: [20377]: RECV received frame number 13 Oct 30 10:26:11.75: [20377]: RECV received frame number 14 Oct 30 10:26:12.00: [20377]: RECV received frame number 15 Oct 30 10:26:12.15: [20377]: RECV received frame number 16 Oct 30 10:26:12.29: [20377]: RECV received frame number 17 Oct 30 10:26:12.43: [20377]: RECV received frame number 18 Oct 30 10:26:12.57: [20377]: RECV received frame number 19 Oct 30 10:26:12.71: [20377]: RECV received frame number 20 Oct 30 10:26:12.71: [20377]: RECV frame FCS check failed Oct 30 10:26:12.71: [20377]: Bad HDLC terminating flag received. Oct 30 10:26:12.71: [20377]: Bad HDLC terminating flag received. Oct 30 10:26:12.71: [20377]: HDLC frame not byte-oriented. Trailing byte: 0xf8 Oct 30 10:26:12.71: [20377]: HDLC frame not byte-oriented. Trailing byte: 0xfc Oct 30 10:26:12.83: [20377]: HDLC frame not byte-oriented. Trailing byte: 0xf0 Oct 30 10:26:12.83: [20377]: HDLC frame not byte-oriented. Trailing byte: 0 Oct 30 10:26:13.11: [20377]: RECV received frame number 23 Oct 30 10:26:13.25: [20377]: RECV received frame number 24 Oct 30 10:26:13.39: [20377]: RECV received frame number 25 Oct 30 10:26:13.65: [20377]: RECV received frame number 26 Oct 30 10:26:13.79: [20377]: RECV received frame number 27 Oct 30 10:26:13.93: [20377]: RECV received frame number 28 Oct 30 10:26:14.07: [20377]: RECV received frame number 29 Oct 30 10:26:14.21: [20377]: RECV received frame number 30 Oct 30 10:26:14.33: [20377]: RECV received frame number 31 Oct 30 10:26:14.47: [20377]: RECV received frame number 32 Oct 30 10:26:14.61: [20377]: RECV received frame number 33 Oct 30 10:26:14.75: [20377]: RECV received frame number 34 Oct 30 10:26:14.89: [20377]: RECV received frame number 35 Oct 30 10:26:15.03: [20377]: RECV received frame number 36 Oct 30 10:26:15.29: [20377]: RECV received frame number 37 Oct 30 10:26:15.43: [20377]: RECV received frame number 38 Oct 30 10:26:15.57: [20377]: RECV received frame number 39 Oct 30 10:26:15.71: [20377]: RECV received frame number 40 Oct 30 10:26:15.85: [20377]: RECV received frame number 41 Oct 30 10:26:15.98: [20377]: RECV received frame number 42 Oct 30 10:26:16.12: [20377]: RECV received frame number 43 Oct 30 10:26:16.27: [20377]: RECV received frame number 44 Oct 30 10:26:16.41: [20377]: RECV received frame number 45 Oct 30 10:26:16.55: [20377]: RECV received frame number 46 Oct 30 10:26:16.67: [20377]: RECV received frame number 47 Oct 30 10:26:16.81: [20377]: RECV received frame number 48 Oct 30 10:26:17.08: [20377]: RECV received frame number 49 Oct 30 10:26:17.22: [20377]: RECV received frame number 50 Oct 30 10:26:17.37: [20377]: RECV received frame number 51 Oct 30 10:26:17.22: [20377]: RECV received frame number 50 Oct 30 10:26:17.37: [20377]: RECV received frame number 51 Oct 30 10:26:17.51: [20377]: RECV received frame number 52 Oct 30 10:26:17.65: [20377]: RECV received frame number 53 Oct 30 10:26:17.79: [20377]: RECV received frame number 54 Oct 30 10:26:17.91: [20377]: RECV received frame number 55 Oct 30 10:26:18.05: [20377]: RECV received frame number 56 Oct 30 10:26:18.19: [20377]: RECV received frame number 57 Oct 30 10:26:18.33: [20377]: RECV received frame number 58 Oct 30 10:26:18.47: [20377]: RECV received frame number 59 Oct 30 10:26:18.61: [20377]: RECV received frame number 60 Oct 30 10:26:18.88: [20377]: RECV received frame number 61 Oct 30 10:26:19.03: [20377]: RECV received frame number 62 Oct 30 10:26:19.15: [20377]: RECV received frame number 63 Oct 30 10:26:19.29: [20377]: RECV received frame number 64 Oct 30 10:26:19.43: [20377]: RECV received frame number 65 Oct 30 10:26:19.57: [20377]: RECV received frame number 66 Oct 30 10:26:19.71: [20377]: RECV received frame number 67 Oct 30 10:26:19.85: [20377]: RECV received frame number 68 Oct 30 10:26:19.97: [20377]: RECV received frame number 69 Oct 30 10:26:20.11: [20377]: RECV received frame number 70 Oct 30 10:26:20.39: [20377]: RECV received frame number 71 Oct 30 10:26:20.53: [20377]: RECV received frame number 72 Oct 30 10:26:20.65: [20377]: RECV received frame number 73 Oct 30 10:26:20.79: [20377]: RECV received frame number 74 Oct 30 10:26:20.89: [20377]: RECV received frame number 75 Oct 30 10:26:20.89: [20377]: RECV received RCP frame Oct 30 10:26:20.89: [20377]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled Oct 30 10:26:20.89: [20377]: MODEM input buffering disabled Oct 30 10:26:20.89: [20377]: --> [10:NO CARRIER] Oct 30 10:26:20.89: [20377]: <-- [9:AT+FRH=3\r] Oct 30 10:26:21.09: [20377]: --> [7:CONNECT] Oct 30 10:26:22.25: [20377]: --> HDLC<9:FF C8 FD F4 00 00 D2 B8 9D> Oct 30 10:26:22.33: [20377]: --> [2:OK] Oct 30 10:26:22.33: [20377]: RECV recv PPS (partial page signal) Oct 30 10:26:22.33: [20377]: RECV recv EOP (no more pages or documents) Oct 30 10:26:22.33: [20377]: RECV received 76 frames of block 1 of page 1 Oct 30 10:26:22.33: [20377]: <-- [9:AT+FRS=7\r] Oct 30 10:26:22.41: [20377]: --> [2:OK] Oct 30 10:26:22.41: [20377]: <-- [9:AT+FTH=3\r] Oct 30 10:26:22.42: [20377]: --> [7:CONNECT] Oct 30 10:26:22.42: [20377]: <-- HDLC<35:FF C8 3D 00 00 0E 00 00 00 00 00 00 0F FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF> Oct 30 10:26:22.42: [20377]: <-- data [35] Oct 30 10:26:22.42: [20377]: <-- data [2] Oct 30 10:26:24.46: [20377]: --> [2:OK] Oct 30 10:26:24.46: [20377]: RECV send PPR (partial page request) Oct 30 10:26:24.46: [20377]: <-- [11:AT+FRM=146\r] Oct 30 10:26:25.20: [20377]: --> [7:CONNECT] Oct 30 10:26:25.20: [20377]: MODEM input buffering enabled Oct 30 10:26:25.20: [20377]: MODEM set XON/XOFF/FLUSH: input ignored, output generated Oct 30 10:26:25.63: [20377]: RECV received frame number 20 Oct 30 10:26:25.77: [20377]: RECV received frame number 21 Oct 30 10:26:25.89: [20377]: RECV received frame number 22 Oct 30 10:26:25.89: [20377]: RECV received RCP frame Oct 30 10:26:25.89: [20377]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled Oct 30 10:26:25.89: [20377]: MODEM input buffering disabled Oct 30 10:26:25.89: [20377]: --> [10:NO CARRIER] Oct 30 10:26:25.89: [20377]: <-- [9:AT+FRH=3\r] Oct 30 10:26:26.07: [20377]: --> [7:CONNECT] Oct 30 10:26:25.89: [20377]: <-- [9:AT+FRH=3\r] Oct 30 10:26:26.07: [20377]: --> [7:CONNECT] Oct 30 10:26:27.25: [20377]: --> HDLC<9:FF C8 FD F4 00 00 40 1B 66> Oct 30 10:26:27.35: [20377]: --> [2:OK] Oct 30 10:26:27.35: [20377]: RECV recv PPS (partial page signal) Oct 30 10:26:27.35: [20377]: RECV recv EOP (no more pages or documents) Oct 30 10:26:27.35: [20377]: RECV received 3 frames of block 1 of page 1 Oct 30 10:26:27.37: [20377]: RECV/CQ: Adjusting for EOFB at row 1077 Oct 30 10:26:27.37: [20377]: RECV: 19447 bytes of data, 1077 total lines Oct 30 10:26:27.37: [20377]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled Oct 30 10:26:27.37: [20377]: <-- [9:AT+FRS=7\r] Oct 30 10:26:27.41: [20377]: --> [2:OK] Oct 30 10:26:27.41: [20377]: RECV send MCF (message confirmation) Oct 30 10:26:27.41: [20377]: <-- [9:AT+FTH=3\r] Oct 30 10:26:27.42: [20377]: --> [7:CONNECT] Oct 30 10:26:27.42: [20377]: <-- HDLC<3:FF C8 31> Oct 30 10:26:27.42: [20377]: <-- data [3] Oct 30 10:26:27.42: [20377]: <-- data [2] Oct 30 10:26:28.50: [20377]: --> [2:OK] Oct 30 10:26:28.50: [20377]: <-- [9:AT+FRH=3\r] Oct 30 10:26:28.77: [20377]: --> [7:CONNECT] Oct 30 10:26:29.84: [20377]: --> HDLC<5:FF C8 DF 59 6F> Oct 30 10:26:29.94: [20377]: --> [2:OK] Oct 30 10:26:29.94: [20377]: RECV recv DCN (disconnect) Oct 30 10:26:29.94: [20377]: MODEM input buffering enabled Oct 30 10:26:29.94: [20377]: RECV FAX (000000110): from Via Fax, page 1 in 0:28, INF, 3.85 line/mm, 2-D MMR, 14400 bit/s Oct 30 10:26:30.95: [20377]: RECV FAX (000000110): recvq/fax000000038.tif from Via Fax, subaddress <unspecified>, 1 pages in 0:30 Oct 30 10:26:30.95: [20377]: RECV FAX: bin/faxrcvd 'recvq/fax000000038.tif' 'ttyIAX0' '000000110' '' '' '' '<NONE>' '2116' Oct 30 10:26:30.95: [20377]: RECV FAX: end Oct 30 10:26:30.95: [20377]: SESSION END

Lee Howard wrote:

Shawn Henderson wrote:
I am very very new to hylafax .. I just set up a server with iaxmodem connected to asterisk.. works great .. I have two people that send faxes out of a hundred that the faxes appear compressed overlapping the top few lines with each other , some in the middle and also at the bottom. Normally wouldn't be a problem but these are hospitals sending lab reports and the most important parts seem to be the ones with overlapping lines.. Setup is PRI---> *---> Hylafax ---Printer . We have sat * before a legacy NEC pbx which a fax machine is connected. When we take * and hylafax out of the loop and have faxes go from PRI --->NEC--->Fax they print out fine. It has to have something to do with Asterisk because when the setup is PRI--->* ---->NEC---Fax we have the same problem. I have searched for about two weeks and found some problems with headers but nothing like I am seeing .. any help or ideas would be great.. Thanks..
Current physical setup is             PRI --->REDFONE--->*/hylafax
                                                                      |
                                                                  NEC
Please, let's look at the session logs found in /var/spool/hylafax/log. Send a sample one here.

Thanks,

Lee.

____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] wierd faxes..
  - From: Lee Howard

References:
- [hylafax-users] wierd faxes..
  - From: Shawn Henderson
- Re: [hylafax-users] wierd faxes..
  - From: Lee Howard

Prev by Date: Re: [hylafax-users] wierd faxes..
Next by Date: Re: [hylafax-users] wierd faxes..
Previous by thread: Re: [hylafax-users] wierd faxes..
Next by thread: Re: [hylafax-users] wierd faxes..
Index(es):
- Main
- Thread

Project hosted by iFAX Solutions