[hylafax-users] Problems with Hylafax 4.4.1 (the error of HDLC frame too short)

["Eduardo Diaz - Gmail" <ediazrod@xxxxxxxxx>]

Hi All
I have a problem receiving and sending faxes.
I am unable to send faxes I try to change the moden to another model
but I have the same problem
I have linux kernel 
2.6.17.1
The modem is a Modem Fax Voz de Conceptronic 56K C56EW
The fax machine is a Brother Fax (I try many fax machines with the
same result)
The hylafax version is 4.4.1 (in a debian 4.0)

Ok I am using this fax in other machine (is a diferente hardware, but
very similar debian version) and run very well.

But in this machine I never get a fax:

The log output.

Oct 18 01:09:15.27: [26630]: SESSION BEGIN 000000071 3491913293273
Oct 18 01:09:15.27: [26630]: HylaFAX (tm) Version 
4.4.1
Oct 18 01:09:15.27: [26630]: SEND FAX: JOB 30 DEST 913293273 COMMID
000000071 DEVICE '/dev/ttyS0' FROM 'adminfax
<adminfax@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
>' USER adminfax
Oct 18 01:09:15.27: [26630]: STATE CHANGE: RUNNING -> SENDING
Oct 18 01:09:15.27: [26630]: Apply DialString rules to "913293273"
Oct 18 01:09:15.27: [26630]: --> return result "913293273"
Oct 18 01:09:15.27: [26630]: <-- [12:AT+FCLASS=1\r]
Oct 18 01:09:15.38: [26630]: --> [2:OK]
Oct 18 01:09:15.38: [26630]: DIAL 913293273
Oct 18 01:09:15.38: [26630]: <-- [14:ATDT913293273\r]
Oct 18 01:09:
33.52: [26630]: --> [7:CONNECT]
Oct 18 01:09:34.82: [26630]: --> HDLC<16:FF C0 04 00 00 6A AA AA 00 31
09 01 86 80 7C 82>
Oct 18 01:09:34.82: [26630]: --> [2:OK]
Oct 18 01:09:34.82: [26630]: REMOTE NSF "00 00 56 55 55 00 8C 90 80 61
01 3E 41"
Oct 18 01:09:34.82: [26630]: NSF remote fax equipment: Brother
MFC-3100C/MFC-8600
Oct 18 01:09:34.82: [26630]: <-- [9:AT+FRH=3\r]
Oct 18 01:09:34.83: [26630]: --> [7:CONNECT]
Oct 18 01:09:
35.14: [26630]: --> HDLC<11:FF C8 01 00 77 15 23 01 88 E7
CD>
Oct 18 01:09:35.17: [26630]: --> [2:OK]
Oct 18 01:09:35.17: [26630]: REMOTE best rate 14400 bit/s
Oct 18 01:09:35.17: [26630]: REMOTE max A4 page width (215 mm)
Oct 18 01:09:35.17: [26630]: REMOTE max unlimited page length
Oct 18 01:09:35.17: [26630]: REMOTE best vres 15.4 line/mm
Oct 18 01:09:35.17: [26630]: REMOTE format support: MH, MR, MMR
Oct 18 01:09:35.17: [26630]: REMOTE supports 
T.30 Annex A, 256-byte
ECM
Oct 18 01:09:35.17: [26630]: REMOTE best 10 ms/scanline
Oct 18 01:09:35.17: [26630]: USE 9600 bit/s
Oct 18 01:09:35.17: [26630]: USE error correction mode
Oct 18 01:09:35.17: [26630]: SEND file "docq/doc32.pdf;c0"
Oct 18 01:09:35.17: [26630]: USE A4 page width (215 mm)
Oct 18 01:09:35.17: [26630]: USE unlimited page length
Oct 18 01:09:35.17: [26630]: USE 3.85 line/mm
Oct 18 01:09:35.17: [26630]: USE 2-D MMR
Oct 18 01:09:
35.17: [26630]: USE 0 ms/scanline
Oct 18 01:09:35.17: [26630]: SEND training at v.29 9600 bit/s
Oct 18 01:09:35.17: [26630]: DELAY 70 ms
Oct 18 01:09:35.24: [26630]: <-- [9:AT+FTH=3\r]
Oct 18 01:09:35.29: [26630]: --> [7:CONNECT]
Oct 18 01:09:35.29: [26630]: <-- HDLC<23:FF C0 C2 74 82 74 CA 04 26 96
4E 26 86 B2 36 A6 26 76 92 04 04 04 04>
Oct 18 01:09:35.29: [26630]: <-- data [23]
Oct 18 01:09:35.29: [26630]: <-- data [2]
Oct 18 01:09:35.32: [26630]: --> [7:CONNECT]
Oct 18 01:09:35.32: [26630]: <-- HDLC<7:FF C8 C1 00 60 1F 22>
Oct 18 01:09:35.32: [26630]: <-- data [7]
Oct 18 01:09:35.32: [26630]: <-- data [2]
Oct 18 01:09:37.51: [26630]: --> [2:OK]
Oct 18 01:09:37.51: [26630]: DELAY 70 ms
Oct 18 01:09:37.58: [26630]: <-- [10:AT+FTM=96\r]
Oct 18 01:09:38.10: [26630]: --> [7:CONNECT]
Oct 18 01:09:38.10: [26630]: <-- data [1024]
Oct 18 01:09:38.10: [26630]: <-- data [776]
Oct 18 01:09:38.10: [26630]: <-- data [2]
Oct 18 01:09:39.64: [26630]: --> [2:OK]
Oct 18 01:09:39.64: [26630]: <-- [9:AT+FRH=3\r]
Oct 18 01:09:39.80: [26630]: --> [7:CONNECT]
Oct 18 01:09:42.24: [26630]: --> [20:76 40 40 40 40 40 40 40 00 20 20
90 3F 4A AB 43 96 98 4E 7E]
Oct 18 01:09:42.24: [26630]: --> [20:28 53 49 C2 D0 B4 D1 2C 91 B8 16
8C 6E C5 44 05 05 6B 9D 26]
Oct 18 01:09:
42.24: [26630]: --> [7:09 6D A2 4B 38 10 03]
Oct 18 01:09:42.24: [26630]: --> [2:OK]
Oct 18 01:09:42.24: [26630]: HDLC frame too short (0 bytes)
Oct 18 01:09:42.24: [26630]: DELAY 70 ms
Oct 18 01:09:42.31
: [26630]: <-- [9:AT+FTH=3\r]
Oct 18 01:09:42.36: [26630]: --> [7:CONNECT]
Oct 18 01:09:42.36: [26630]: <-- HDLC<3:FF C8 D8>
Oct 18 01:09:42.36: [26630]: <-- data [3]
Oct 18 01:09:42.36: [26630]: <-- data [2]
Oct 18 01:09:43.67: [26630]: --> [2:OK]
Oct 18 01:09:43.67: [26630]: SEND send CRP (command repeat)
Oct 18 01:09:43.67: [26630]: <-- [9:AT+FRH=3\r]
Oct 18 01:09:43.92: [26630]: --> [7:CONNECT]
Oct 18 01:09:
44.99: [26630]: --> HDLC<5:FF C8 5F C8 E7>
Oct 18 01:09:45.03: [26630]: --> [2:OK]
Oct 18 01:09:45.03: [26630]: TRAINING failed
Oct 18 01:09:45.03: [26630]: DELAY 70 ms
Oct 18 01:09:45.10: [26630]: <-- [9:AT+FTH=3\r]
Oct 18 01:09:45.15: [26630]: --> [7:CONNECT]
Oct 18 01:09:45.15: [26630]: <-- HDLC<3:FF C8 DF>
Oct 18 01:09:45.15: [26630]: <-- data [3]
Oct 18 01:09:45.15: [26630]: <-- data [2]
Oct 18 01:09:
46.46: [26630]: --> [2:OK]
Oct 18 01:09:46.46: [26630]: MODEM input buffering enabled
Oct 18 01:09:47.46: [26630]: <-- [5:ATH0\r]
Oct 18 01:09:47.56: [26630]: --> [10:NO CARRIER]
Oct 18 01:09:47.56: [26630]: MODEM No carrier
Oct 18 01:09:47.56: [26630]: MODEM set DTR OFF
Oct 18 01:09:47.56: [26630]: STATE CHANGE: SENDING -> MODEMWAIT
(timeout 5)
Oct 18 01:09:47.56: [26630]: SESSION END


the config of ttyS0

CountryCode:            34
AreaCode:               91
FAXNumber:              "+34917966326"
LongDistancePrefix:     00
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         0xffffffff
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      12
SpeakerVolume:          "Medium"
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "IndelMadrid S.A."
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxConsecutiveBadLines: 10
MaxRecvPages:           "200"
#

ModemType:              Class1          # use this to supply a hint
ModemRate:              19200
ModemFlowControl:       rtscts

# as of v1.20, +FTS is not supported, which will cause "Stop and wait"
# failures unless we use software pauses instead...
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1FlowControlCmd:   rtscts
Class1TCFResponseDelay: 75              # 75ms delay between recv TCF
& response
Class1SendPPMDelay:     75              # 75ms delay before sending
PPM
Class1SendTCFDelay:     75              # 75ms delay between sending
DCS & TCF
Class1TrainingRecovery: 1500            # 
1.5sec delay after training
failure
Class1RecvAbortOK:      200             # wait 200ms for abort
response
Class1FrameOverhead:    4               # 4 byte overhead in recvd
HDLC frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident
frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-
zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF
duration
Class1PPMWaitCmd:       "<delay\0727>"  # \072 == :  to avoid awk
problem
Class1TCFWaitCmd:       "<delay\0727>"
Class1EOPWaitCmd:       "<delay\0729>"
Class1SwitchingCmd:     "<delay\0727>"  # assumption: +FRS not
supported


I try all, :-( but never get sucess, it is posible that muy change the
serial port of my motherboard???)

or can be the line (this line are using one ADSL and other fax and
don't have any problem problem this this...
:-)

any idea? this is the serial bus in lshw

     *-serial
          description: SMBus
          product: CK804 SMBus
          vendor: nVidia Corporation
          physical id: 1.1
          bus info: 
pci@00:01.1
          version: a2
          width: 32 bits
          clock: 66MHz
          capabilities: cap_list
          configuration: driver=nForce2_smbus latency=0 maxlatency=1
mingnt=3
          resources: ioport:e400-e41f ioport:4c00-4c3f ioport:
4c40-4c7f irq:255



REgards and thanks for all!!