HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: [hylafax-users] COMREC received DCN problem

To: <roberto.garuti@xxxxxxx>, <hylafax-users@xxxxxxxxxxx>
Subject: Re: [hylafax-users] COMREC received DCN problem
From: "Andrew Rinaldi" <andrew.rinaldi@xxxxxxxxxxxx>
Reply-to: <andrew.rinaldi@xxxxxxxxxxxx>
Date: Thu, 27 Sep 2007 17:47:37 +0100

Hi Roberto,

Upgrade to the latest HylaFAX version... a lot of fax protocol development has taken place since version 4.2.3

Regards

ANDREW RINALDI

Mainpine Developer Support

USA +1 503 822 9944 | UK +44 8458 909438

andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com

From: hylafax-users-bounce@xxxxxxxxxxx [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Roberto Garuti
Sent: 27 September 2007 17:19
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] COMREC received DCN problem

Hi,

I've an hylfax 4.2.3 on a Fedora core 6 system with a Multitech ISI5634UPCI/8-EURO card and all seams works fine except for many, many fax error during fax receiving; the problem is that this kind of errors come from different sender so I can't undestand the problem.
Can anyone help me ???
Can this problem be fixed ?

Attached I send the trasmission log of the wrong fax.

Thanks.

Roberto

Sep 27 10:16:26.19: [27227]: SESSION BEGIN 000002511 390506332229

Sep 27 10:16:26.19: [27227]: HylaFAX (tm) Version 4.2.3

Sep 27 10:16:26.19: [27227]: <-- [4:ATA\r]

Sep 27 10:16:36.81: [27227]: --> [7:CONNECT]

Sep 27 10:16:36.81: [27227]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS2'

Sep 27 10:16:36.81: [27227]: RECV FAX: begin

Sep 27 10:16:36.81: [27227]: <-- data [32]

Sep 27 10:16:36.81: [27227]: <-- data [2]

Sep 27 10:16:36.84: [27227]: --> [7:CONNECT]

Sep 27 10:16:36.84: [27227]: <-- data [23]

Sep 27 10:16:36.84: [27227]: <-- data [2]

Sep 27 10:16:36.86: [27227]: --> [7:CONNECT]

Sep 27 10:16:36.86: [27227]: <-- data [13]

Sep 27 10:16:36.86: [27227]: <-- data [2]

Sep 27 10:16:39.14: [27227]: --> [2:OK]

Sep 27 10:16:39.14: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:16:39.38: [27227]: --> [7:CONNECT]

Sep 27 10:16:41.59: [27227]: --> [2:OK]

Sep 27 10:16:41.59: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:16:41.61: [27227]: --> [7:CONNECT]

Sep 27 10:16:42.33: [27227]: --> [2:OK]

Sep 27 10:16:42.33: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:16:42.35: [27227]: --> [7:CONNECT]

Sep 27 10:16:42.71: [27227]: --> [2:OK]

Sep 27 10:16:42.71: [27227]: DELAY 1500 ms

Sep 27 10:16:44.21: [27227]: <-- [9:AT+FTH=3\r]

Sep 27 10:16:45.18: [27227]: --> [7:CONNECT]

Sep 27 10:16:45.18: [27227]: <-- data [32]

Sep 27 10:16:45.18: [27227]: <-- data [2]

Sep 27 10:16:45.21: [27227]: --> [7:CONNECT]

Sep 27 10:16:45.21: [27227]: <-- data [23]

Sep 27 10:16:45.21: [27227]: <-- data [2]

Sep 27 10:16:45.23: [27227]: --> [7:CONNECT]

Sep 27 10:16:45.23: [27227]: <-- data [13]

Sep 27 10:16:45.23: [27227]: <-- data [2]

Sep 27 10:16:47.51: [27227]: --> [2:OK]

Sep 27 10:16:47.51: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:16:48.09: [27227]: --> [7:CONNECT]

Sep 27 10:16:49.84: [27227]: --> [2:OK]

Sep 27 10:16:49.84: [27227]: REMOTE TSI ""

Sep 27 10:16:49.84: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:16:49.86: [27227]: --> [7:CONNECT]

Sep 27 10:16:50.20: [27227]: --> [2:OK]

Sep 27 10:16:50.20: [27227]: REMOTE wants 14400 bit/s

Sep 27 10:16:50.20: [27227]: REMOTE wants A4 page width (215 mm)

Sep 27 10:16:50.20: [27227]: REMOTE wants unlimited page length

Sep 27 10:16:50.20: [27227]: REMOTE wants 3.85 line/mm

Sep 27 10:16:50.20: [27227]: REMOTE wants 2-D MMR

Sep 27 10:16:50.20: [27227]: REMOTE wants T.30 Annex A, 256-byte ECM

Sep 27 10:16:50.20: [27227]: RECV training at v.17 14400 bit/s

Sep 27 10:16:50.20: [27227]: <-- [11:AT+FRM=145\r]

Sep 27 10:16:51.72: [27227]: --> [7:CONNECT]

Sep 27 10:16:53.28: [27227]: RECV: TCF 2800 bytes, 0% non-zero, 2795 zero-run

Sep 27 10:16:53.29: [27227]: --> [10:NO CARRIER]

Sep 27 10:16:53.29: [27227]: DELAY 70 ms

Sep 27 10:16:53.36: [27227]: TRAINING succeeded

Sep 27 10:16:53.36: [27227]: <-- [9:AT+FTH=3\r]

Sep 27 10:16:54.33: [27227]: --> [7:CONNECT]

Sep 27 10:16:54.33: [27227]: <-- data [3]

Sep 27 10:16:54.33: [27227]: <-- data [2]

Sep 27 10:16:54.72: [27227]: --> [2:OK]

Sep 27 10:16:54.72: [27227]: <-- [11:AT+FRM=146\r]

Sep 27 10:16:58.67: [27227]: --> [8:+FCERROR]

Sep 27 10:16:58.67: [27227]: <-- [11:AT+FRM=146\r]

Sep 27 10:16:58.79: [27227]: --> [8:+FCERROR]

Sep 27 10:16:58.79: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:16:58.89: [27227]: --> [7:CONNECT]

Sep 27 10:17:00.35: [27227]: --> [2:OK]

Sep 27 10:17:00.35: [27227]: RECV recv TSI (sender id)

Sep 27 10:17:00.35: [27227]: REMOTE TSI ""

Sep 27 10:17:00.35: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:17:00.36: [27227]: --> [7:CONNECT]

Sep 27 10:17:00.69: [27227]: --> [2:OK]

Sep 27 10:17:00.69: [27227]: REMOTE wants 14400 bit/s

Sep 27 10:17:00.69: [27227]: REMOTE wants A4 page width (215 mm)

Sep 27 10:17:00.69: [27227]: REMOTE wants unlimited page length

Sep 27 10:17:00.69: [27227]: REMOTE wants 3.85 line/mm

Sep 27 10:17:00.69: [27227]: REMOTE wants 2-D MMR

Sep 27 10:17:00.69: [27227]: REMOTE wants T.30 Annex A, 256-byte ECM

Sep 27 10:17:00.69: [27227]: RECV training at v.17 14400 bit/s

Sep 27 10:17:00.69: [27227]: <-- [11:AT+FRM=145\r]

Sep 27 10:17:02.22: [27227]: --> [7:CONNECT]

Sep 27 10:17:03.78: [27227]: RECV: TCF 2800 bytes, 0% non-zero, 2790 zero-run

Sep 27 10:17:03.78: [27227]: --> [10:NO CARRIER]

Sep 27 10:17:03.78: [27227]: DELAY 70 ms

Sep 27 10:17:03.85: [27227]: TRAINING succeeded

Sep 27 10:17:03.85: [27227]: <-- [9:AT+FTH=3\r]

Sep 27 10:17:04.82: [27227]: --> [7:CONNECT]

Sep 27 10:17:04.82: [27227]: <-- data [3]

Sep 27 10:17:04.82: [27227]: <-- data [2]

Sep 27 10:17:05.22: [27227]: --> [2:OK]

Sep 27 10:17:05.22: [27227]: <-- [11:AT+FRM=146\r]

Sep 27 10:17:09.19: [27227]: --> [8:+FCERROR]

Sep 27 10:17:09.19: [27227]: <-- [11:AT+FRM=146\r]

Sep 27 10:17:09.32: [27227]: --> [8:+FCERROR]

Sep 27 10:17:09.32: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:17:09.44: [27227]: --> [7:CONNECT]

Sep 27 10:17:10.85: [27227]: --> [2:OK]

Sep 27 10:17:10.85: [27227]: RECV recv TSI (sender id)

Sep 27 10:17:10.85: [27227]: REMOTE TSI ""

Sep 27 10:17:10.85: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:17:10.87: [27227]: --> [7:CONNECT]

Sep 27 10:17:11.21: [27227]: --> [2:OK]

Sep 27 10:17:11.21: [27227]: REMOTE wants 14400 bit/s

Sep 27 10:17:11.21: [27227]: REMOTE wants A4 page width (215 mm)

Sep 27 10:17:11.21: [27227]: REMOTE wants unlimited page length

Sep 27 10:17:11.21: [27227]: REMOTE wants 3.85 line/mm

Sep 27 10:17:11.21: [27227]: REMOTE wants 2-D MMR

Sep 27 10:17:11.21: [27227]: REMOTE wants T.30 Annex A, 256-byte ECM

Sep 27 10:17:11.21: [27227]: RECV training at v.17 14400 bit/s

Sep 27 10:17:11.21: [27227]: <-- [11:AT+FRM=145\r]

Sep 27 10:17:12.72: [27227]: --> [7:CONNECT]

Sep 27 10:17:14.29: [27227]: RECV: TCF 2800 bytes, 0% non-zero, 2796 zero-run

Sep 27 10:17:14.29: [27227]: --> [10:NO CARRIER]

Sep 27 10:17:14.29: [27227]: DELAY 70 ms

Sep 27 10:17:14.36: [27227]: TRAINING succeeded

Sep 27 10:17:14.36: [27227]: <-- [9:AT+FTH=3\r]

Sep 27 10:17:15.33: [27227]: --> [7:CONNECT]

Sep 27 10:17:15.33: [27227]: <-- data [3]

Sep 27 10:17:15.33: [27227]: <-- data [2]

Sep 27 10:17:15.72: [27227]: --> [2:OK]

Sep 27 10:17:15.72: [27227]: <-- [11:AT+FRM=146\r]

Sep 27 10:17:16.83: [27227]: --> [8:+FCERROR]

Sep 27 10:17:16.83: [27227]: <-- [11:AT+FRM=146\r]

Sep 27 10:17:16.95: [27227]: --> [8:+FCERROR]

Sep 27 10:17:16.95: [27227]: <-- [9:AT+FRH=3\r]

Sep 27 10:17:17.07: [27227]: --> [7:CONNECT]

Sep 27 10:17:17.95: [27227]: --> [2:OK]

Sep 27 10:17:17.95: [27227]: RECV recv DCN (disconnect)

Sep 27 10:17:17.95: [27227]: COMREC received DCN

Sep 27 10:17:17.95: [27227]: RECV FAX (000002511): recvq/fax000001235.tif from , route to <unspecified>, 0 pages in 0:41

Sep 27 10:17:17.95: [27227]: RECV FAX: COMREC received DCN

Sep 27 10:17:17.95: [27227]: RECV FAX (000002511): session with  terminated abnormally: COMREC received DCN

Sep 27 10:17:17.95: [27227]: RECV FAX: bin/faxrcvd "recvq/fax000001235.tif" "ttyS2" "000002511" "COMREC received DCN"

Sep 27 10:17:17.95: [27227]: RECV FAX: end

Sep 27 10:17:17.95: [27227]: SESSION END

References:
- [hylafax-users] COMREC received DCN problem
  - From: Roberto Garuti

Prev by Date: [hylafax-users] Digi AccelePort RAS 4 "COMREC invalid response received"
Next by Date: Re: [hylafax-users] Digi AccelePort RAS 4 "COMREC invalid response received"
Previous by thread: [hylafax-users] COMREC received DCN problem
Next by thread: Re: [hylafax-users] COMREC received DCN problem
Index(es):
- Main
- Thread

Project hosted by iFAX Solutions