 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Problem receiving on MultiTech MT5634ZPX
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Problem receiving on MultiTech MT5634ZPX
- From: dario busso <dario.busso@xxxxxxxxxxxx>
- Date: Fri, 06 Apr 2007 10:48:39 +0200
Here I reported the trace of a fax sent with the problem in the object. The system is: Linux FaxMailServer 2.6.17-10-server #2 SMP Fri Oct 13 18:47:26 UTC 2006 i686 GNU/Linux and the hylafax version is: hylafax ver 4.3.0 --------------------------------------------------------------------- apr 04 09:08:26.57: [ 5587]: SESSION BEGIN 000004023 39175xxxxxx apr 04 09:08:26.57: [ 5587]: HylaFAX (tm) Version 4.3.0 apr 04 09:08:26.57: [ 5587]: SEND FAX: JOB 1222 DEST 0175xxxxxx COMMID 000004023 DEVICE '/dev/ttyS1' FROM '---- SPA SIMONA <simona@xxxxxxx>' USER fax apr 04 09:08:26.57: [ 5587]: <-- [12:AT+FCLASS=1\r] apr 04 09:08:26.58: [ 5587]: --> [2:OK] apr 04 09:08:26.58: [ 5587]: DIAL 0175xxxxxx apr 04 09:08:26.58: [ 5587]: <-- [15:ATDT0175xxxxxx\r] apr 04 09:08:39.52: [ 5587]: --> [7:CONNECT] apr 04 09:08:41.55: [ 5587]: --> [2:OK] apr 04 09:08:41.55: [ 5587]: REMOTE NSF "B5 00 AA 48 79 6C 61 46 41 58 20 28 74 6D 29 20 56 65 72 73 69 6F 6E 20 34 2E 32 2E 30" apr 04 09:08:41.55: [ 5587]: NSF remote fax equipment: HylaFAX apr 04 09:08:41.55: [ 5587]: NSF remote station ID: "HylaFAX (tm) Version 4.2.0" apr 04 09:08:41.55: [ 5587]: <-- [9:AT+FRH=3\r] apr 04 09:08:41.56: [ 5587]: --> [7:CONNECT] apr 04 09:08:42.38: [ 5587]: --> [2:OK] apr 04 09:08:42.38: [ 5587]: REMOTE CSI "------- fax:+390175xx" apr 04 09:08:42.38: [ 5587]: <-- [9:AT+FRH=3\r] apr 04 09:08:42.39: [ 5587]: --> [7:CONNECT] apr 04 09:08:42.87: [ 5587]: --> [2:OK] apr 04 09:08:42.87: [ 5587]: REMOTE best rate 14400 bit/s apr 04 09:08:42.87: [ 5587]: REMOTE max A3 page width (303 mm) apr 04 09:08:42.87: [ 5587]: REMOTE max unlimited page length apr 04 09:08:42.87: [ 5587]: REMOTE best vres R16 x 15.4 line/mm apr 04 09:08:42.87: [ 5587]: REMOTE format support: MH, MMR apr 04 09:08:42.87: [ 5587]: REMOTE supports T.30 Annex A, 256-byte ECM apr 04 09:08:42.87: [ 5587]: REMOTE best 0 ms/scanline apr 04 09:08:42.87: [ 5587]: USE 9600 bit/s apr 04 09:08:42.87: [ 5587]: USE error correction mode apr 04 09:08:42.87: [ 5587]: SEND file "docq/doc1222.ps;c0" apr 04 09:08:42.87: [ 5587]: USE A4 page width (215 mm) apr 04 09:08:42.87: [ 5587]: USE unlimited page length apr 04 09:08:42.87: [ 5587]: USE 3.85 line/mm apr 04 09:08:42.87: [ 5587]: USE 2-D MMR apr 04 09:08:42.87: [ 5587]: USE 0 ms/scanline apr 04 09:08:42.87: [ 5587]: SEND training at v.29 9600 bit/s apr 04 09:08:42.87: [ 5587]: <-- [9:AT+FRS=7\r] apr 04 09:08:43.02: [ 5587]: --> [2:OK] apr 04 09:08:43.02: [ 5587]: <-- [9:AT+FTH=3\r] apr 04 09:08:43.98: [ 5587]: --> [7:CONNECT] apr 04 09:08:43.98: [ 5587]: <-- data [23] apr 04 09:08:43.98: [ 5587]: <-- data [2] apr 04 09:08:43.99: [ 5587]: --> [7:CONNECT] apr 04 09:08:43.99: [ 5587]: <-- data [7] apr 04 09:08:43.99: [ 5587]: <-- data [2] apr 04 09:08:45.18: [ 5587]: --> [2:OK] apr 04 09:08:45.18: [ 5587]: <-- [9:AT+FTS=7\r] apr 04 09:08:45.24: [ 5587]: --> [2:OK] apr 04 09:08:45.24: [ 5587]: <-- [10:AT+FTM=96\r] apr 04 09:08:45.25: [ 5587]: --> [7:CONNECT] apr 04 09:08:45.25: [ 5587]: DELAY 400 ms apr 04 09:08:45.65: [ 5587]: <-- data [1024] apr 04 09:08:45.65: [ 5587]: <-- data [776] apr 04 09:08:45.65: [ 5587]: <-- data [2] apr 04 09:08:47.22: [ 5587]: --> [2:OK] apr 04 09:08:47.22: [ 5587]: <-- [9:AT+FRH=3\r] apr 04 09:08:47.55: [ 5587]: --> [7:CONNECT] apr 04 09:08:48.80: [ 5587]: --> [2:OK] apr 04 09:08:48.80: [ 5587]: TRAINING succeeded apr 04 09:08:48.80: [ 5587]: SEND begin page apr 04 09:08:48.82: [ 5587]: SEND EOFB apr 04 09:08:48.82: [ 5587]: SEND send frame number 0 ----- commeted out because no errors display --------- apr 04 09:08:48.83: [ 5587]: SEND send frame number 98 apr 04 09:08:48.83: [ 5587]: DELAY 200 ms apr 04 09:08:49.02: [ 5587]: <-- [10:AT+FTM=96\r] apr 04 09:08:49.03: [ 5587]: --> [7:CONNECT] apr 04 09:08:49.03: [ 5587]: DELAY 400 ms apr 04 09:08:49.43: [ 5587]: <-- data [1031] apr 04 09:08:49.43: [ 5587]: <-- data [1074] apr 04 09:08:49.43: [ 5587]: <-- data [1069] apr 04 09:08:49.43: [ 5587]: <-- data [1069] apr 04 09:08:49.59: [ 5587]: <-- data [1044] apr 04 09:08:49.59: [ 5587]: <-- data [1054] apr 04 09:08:49.59: [ 5587]: <-- data [1066] apr 04 09:08:50.41: [ 5587]: <-- data [1066] apr 04 09:08:51.33: [ 5587]: <-- data [1050] apr 04 09:08:52.11: [ 5587]: <-- data [1051] apr 04 09:08:52.93: [ 5587]: <-- data [1039] apr 04 09:08:53.85: [ 5587]: <-- data [1043] apr 04 09:08:54.66: [ 5587]: <-- data [1039] apr 04 09:08:55.45: [ 5587]: <-- data [1050] apr 04 09:08:56.38: [ 5587]: <-- data [1041] apr 04 09:08:57.21: [ 5587]: <-- data [1043] apr 04 09:08:58.02: [ 5587]: <-- data [1047] apr 04 09:08:58.95: [ 5587]: <-- data [1045] apr 04 09:08:59.74: [ 5587]: <-- data [1041] apr 04 09:09:00.57: [ 5587]: <-- data [1042] apr 04 09:09:01.51: [ 5587]: <-- data [1042] apr 04 09:09:02.34: [ 5587]: <-- data [1048] apr 04 09:09:03.11: [ 5587]: <-- data [1040] apr 04 09:09:04.05: [ 5587]: <-- data [1042] apr 04 09:09:04.85: [ 5587]: <-- data [1050] apr 04 09:09:05.79: [ 5587]: <-- data [1034] apr 04 09:09:06.61: [ 5587]: <-- data [69] apr 04 09:09:06.61: [ 5587]: <-- data [2] apr 04 09:09:11.75: [ 5587]: --> [2:OK] apr 04 09:09:11.75: [ 5587]: <-- [9:AT+FTS=9\r] apr 04 09:09:41.76: [ 5587]: MODEM <Timeout> apr 04 09:09:41.76: [ 5587]: Stop and wait failure (modem on hook) apr 04 09:09:41.76: [ 5587]: SEND end page apr 04 09:09:41.76: [ 5587]: SEND: Stop and wait failure (modem on hook); Giving up after 3 attempts to send same page "docq/doc1222.ps;c0", dirnum 0 apr 04 09:09:41.76: [ 5587]: <-- [9:AT+FTH=3\r] apr 04 09:09:49.32: [ 5587]: --> [0:] apr 04 09:09:49.32: [ 5587]: <-- [5:ATH0\r] apr 04 09:09:54.33: [ 5587]: MODEM <Timeout> apr 04 09:09:54.94: [ 5587]: SESSION END ------------------------------------------------------------------- Th modem that I use is MODEM LT V.92 1.0 MT5634ZPX-PCI-U INTERNAL DATA/FAX/VOICE MODEM VERSION 2.32U . Follow the config.ttyS1 for this modem. -------------------------------------------------------------------- # $Id: lucent,v 1.22 2005/12/05 15:48:54 darren Exp $ # CountryCode: 39 AreaCode: 0172 FAXNumber: "+39 0172xxxxxx" LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "Fax +39 0172.xxxxxx ---- Spa" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" PercentGoodLines: 90 MaxConsecutiveBadLines: 8 MaxRecvPages: 100 # ModemType: Class1 # use class 1 interface ModemFlowControl: rtscts # default Class1TMConnectDelay: 400 # counteract quick CONNECT response Class1PPMWaitCmd: AT+FTS=7 Class1TCFWaitCmd: AT+FTS=7 ModemSoftResetCmd: ATZ # do soft reset of modem ModemHardFlowCmd: AT&K3 # hardware flow control ModemSoftFlowCmd: AT&K4 # software flow control ModemSetupDTRCmd: AT&D3 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier ModemDialCmd: ATDT%s # T for tone dialing, @ for silence ------------------------------------------------------------------- Previously, in my config file, I had't the "Class1EOPWaitCmd: AT+FTS=9" and there was a problem like the following trace. ------------------------------------------------------------------- Apr 03 09:00:31.23: [ 5319]: SENT 24 bytes of data Apr 03 09:00:31.23: [ 5319]: SENT 24 bytes of data Apr 03 09:00:31.23: [ 5319]: SEND 2D RTC Apr 03 09:00:31.23: [ 5319]: SEND end page Apr 03 09:00:36.47: [ 5319]: --> [2:OK] Apr 03 09:00:36.47: [ 5319]: <-- [9:AT+FTS=r] Apr 03 09:01:06.49: [ 5319]: MODEM <Timeout> Apr 03 09:01:06.49: [ 5319]: Stop and wait failure (modem on hook) Apr 03 09:01:06.49: [ 5319]: SEND: Stop and wait failure (modem on hook); Giving up after 3 attempts to send same page "docq/doc1201.ps;40", dirnum 0 Apr 03 09:01:06.49: [ 5319]: <-- [9:AT+FTH=r] Apr 03 09:01:14.06: [ 5319]: --> [0:] Apr 03 09:01:14.06: [ 5319]: <-- [5:] Apr 03 09:01:19.07: [ 5319]: MODEM <Timeout> Apr 03 09:01:19.65: [ 5319]: SESSION END ------------------------------------------------------------------- Any one can help me to solve this issue? Thanks in advance. -- Dario Busso ------------------------ DueDelta via san Biagio, 2 12030 Caramagna Piemonte (CN) Tel: +39 0172 1961277 Mob: +39 339 5956334 Email: dario.busso@xxxxxxxxxxxx ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Problem receiving on MultiTech MT5634ZPX
- From: Jonny Berthiaume
- Re: [hylafax-users] Problem receiving on MultiTech MT5634ZPX
- From: Lee Howard
- Re: [hylafax-users] Problem receiving on MultiTech MT5634ZPX
- Prev by Date: [hylafax-users] another question - update
- Next by Date: Re: [hylafax-users] another question - update
- Previous by thread: Re: [hylafax-users] another question - update
- Next by thread: Re: [hylafax-users] Problem receiving on MultiTech MT5634ZPX
- Index(es):
Project hosted by iFAX Solutions