Re: [hylafax-users] All faxes failing

["Dan Brummer" <dan.brummer@xxxxxxxxx>]

Here are some log outputs from failed faxes:

[root@hylafax02 hylafax]# cat log/c000909913
Apr 04 23:01:23.36: [25966]: SESSION BEGIN 000909913 17022216985
Apr 04 23:01:23.36: [25966]: HylaFAX (tm) Version 4.3.1
Apr 04 23:01:23.36: [25966]: SEND FAX: JOB 832453 DEST 2216985 COMMID
000909913 DEVICE '/dev/ttyIAX-PRI01-01' FROM 'paperclip <paperclip>'
USER paperclip
Apr 04 23:01:23.36: [25966]: STATE CHANGE: RUNNING -> SENDING
Apr 04 23:01:23.36: [25966]: <-- [12:AT+FCLASS=1\r]
Apr 04 23:01:23.36: [25966]: --> [2:OK]
Apr 04 23:01:23.36: [25966]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Apr 04 23:01:23.36: [25966]: DIAL 2216985
Apr 04 23:01:23.36: [25966]: <-- [12:ATDT2216985\r]
Apr 04 23:01:39.51: [25966]: --> [7:CONNECT]
Apr 04 23:01:41.29: [25966]: --> HDLC<32:FF C0 04 00 00 90 00 10 B4 FF
FF FF FF FF FF FF FF FF FF FF FF 80 3C 40 50 08 80 40 80 0C EB 0C>
Apr 04 23:01:41.29: [25966]: --> [2:OK]
Apr 04 23:01:41.29: [25966]: REMOTE NSF "00 00 09 00 08 2D FF FF FF FF
FF FF FF FF FF FF FF FF 01 3C 02 0A 10 01 02 01 30"
Apr 04 23:01:41.29: [25966]: NSF remote fax equipment: Xerox/Toshiba
Apr 04 23:01:41.29: [25966]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:41.33: [25966]: --> [7:CONNECT]
Apr 04 23:01:42.01: [25966]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 04 A4 F3>
Apr 04 23:01:42.01: [25966]: --> [2:OK]
Apr 04 23:01:42.01: [25966]: REMOTE CSI ""
Apr 04 23:01:42.01: [25966]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:42.05: [25966]: --> [7:CONNECT]
Apr 04 23:01:42.49: [25966]: --> HDLC<15:FF C8 01 04 77 19 23 01 EB C1
01 01 04 00 47>
Apr 04 23:01:42.57: [25966]: --> [2:OK]
Apr 04 23:01:42.57: [25966]: REMOTE best rate 33600 bit/s
Apr 04 23:01:42.57: [25966]: REMOTE max A4 page width (215 mm)
Apr 04 23:01:42.57: [25966]: REMOTE max unlimited page length
Apr 04 23:01:42.57: [25966]: REMOTE best vres R16 x 15.4 line/mm
Apr 04 23:01:42.57: [25966]: REMOTE format support: MH, MR, MMR, JBIG
Apr 04 23:01:42.57: [25966]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 04 23:01:42.57: [25966]: REMOTE best 5 ms/scanline
Apr 04 23:01:42.57: [25966]: USE 9600 bit/s
Apr 04 23:01:42.57: [25966]: USE error correction mode
Apr 04 23:01:42.57: [25966]: <-- [9:AT+FTH=3\r]
Apr 04 23:01:42.57: [25966]: --> [7:CONNECT]
Apr 04 23:01:42.57: [25966]: <-- HDLC<3:FF C8 DF>
Apr 04 23:01:42.57: [25966]: <-- data [3]
Apr 04 23:01:42.57: [25966]: <-- data [2]
Apr 04 23:01:43.65: [25966]: --> [2:OK]
Apr 04 23:01:43.65: [25966]: MODEM input buffering enabled
Apr 04 23:01:43.65: [25966]: <-- [5:ATH0\r]
Apr 04 23:01:43.75: [25966]: --> [2:OK]
Apr 04 23:01:43.75: [25966]: MODEM set DTR OFF
Apr 04 23:01:43.75: [25966]: MODEM set baud rate: 0 baud (flow control
unchanged)
Apr 04 23:01:43.75: [25966]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Apr 04 23:01:43.75: [25966]: SESSION END


[root@hylafax02 hylafax]# cat log/c000909912
Apr 04 23:01:22.32: [25956]: SESSION BEGIN 000909912 17023695008
Apr 04 23:01:22.32: [25956]: HylaFAX (tm) Version 4.3.1
Apr 04 23:01:22.32: [25956]: SEND FAX: JOB 832451 DEST 3695008 COMMID
000909912 DEVICE '/dev/ttyIAX-PRI01-22' FROM 'paperclip <paperclip>'
USER paperclip
Apr 04 23:01:22.32: [25956]: STATE CHANGE: RUNNING -> SENDING
Apr 04 23:01:22.32: [25956]: <-- [12:AT+FCLASS=1\r]
Apr 04 23:01:22.32: [25956]: --> [2:OK]
Apr 04 23:01:22.32: [25956]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Apr 04 23:01:22.32: [25956]: DIAL 3695008
Apr 04 23:01:22.32: [25956]: <-- [12:ATDT3695008\r]
Apr 04 23:01:37.97: [25956]: --> [7:CONNECT]
Apr 04 23:01:39.89: [25956]: --> HDLC<38:FF C0 04 00 00 88 01 00 51 92
08 12 82 4A 4A 82 12 CA 04 4A F2 F2 B2 04 4A A2 CA 00 CA 00 01 01 01 30
80 60 0A 42>
Apr 04 23:01:39.89: [25956]: --> [2:OK]
Apr 04 23:01:39.89: [25956]: REMOTE NSF "00 00 11 80 00 8A 49 10 48 41
52 52 41 48 53 20 52 4F 4F 4D 20 52 45 53 00 53 00 80 80 80 0C 01 06"
Apr 04 23:01:39.89: [25956]: NSF remote fax equipment: Canon Laser Class
9000 Series
Apr 04 23:01:39.89: [25956]: NSF remote station ID: "HARRAHS ROOM RES"
Apr 04 23:01:39.89: [25956]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:40.61: [25956]: --> [7:CONNECT]
Apr 04 23:01:40.61: [25956]: --> HDLC<25:FF C0 02 1C 0C 0C AC 9C 6C CC
4C 0C EC 8C 04 04 04 04 04 04 04 04 04 44 88>
Apr 04 23:01:40.61: [25956]: --> [2:OK]
Apr 04 23:01:40.61: [25956]: REMOTE CSI "17023695008"
Apr 04 23:01:40.61: [25956]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:41.01: [25956]: --> [7:CONNECT]
Apr 04 23:01:41.01: [25956]: --> HDLC<15:FF C8 01 04 77 95 23 01 A9 01
01 01 14 18 0F>
Apr 04 23:01:41.05: [25956]: --> [2:OK]
Apr 04 23:01:41.05: [25956]: REMOTE best rate 33600 bit/s
Apr 04 23:01:41.05: [25956]: REMOTE max B4 page width (255 mm)
Apr 04 23:01:41.05: [25956]: REMOTE max unlimited page length
Apr 04 23:01:41.05: [25956]: REMOTE best vres R16 x 15.4 line/mm
Apr 04 23:01:41.05: [25956]: REMOTE format support: MH, MR, MMR, JBIG
Apr 04 23:01:41.05: [25956]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 04 23:01:41.05: [25956]: REMOTE best 10 ms/scanline
Apr 04 23:01:41.05: [25956]: USE 14400 bit/s
Apr 04 23:01:41.05: [25956]: USE error correction mode
Apr 04 23:01:41.05: [25956]: <-- [9:AT+FTH=3\r]
Apr 04 23:01:41.07: [25956]: --> [7:CONNECT]
Apr 04 23:01:41.07: [25956]: <-- HDLC<3:FF C8 DF>
Apr 04 23:01:41.07: [25956]: <-- data [3]
Apr 04 23:01:41.07: [25956]: <-- data [2]
Apr 04 23:01:42.15: [25956]: --> [2:OK]
Apr 04 23:01:42.15: [25956]: MODEM input buffering enabled
Apr 04 23:01:42.15: [25956]: <-- [5:ATH0\r]
Apr 04 23:01:42.27: [25956]: --> [2:OK]
Apr 04 23:01:42.27: [25956]: MODEM set DTR OFF
Apr 04 23:01:42.27: [25956]: MODEM set baud rate: 0 baud (flow control
unchanged)
Apr 04 23:01:42.27: [25956]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Apr 04 23:01:42.27: [25956]: SESSION END


[root@hylafax02 hylafax]# cat log/c000909911
Apr 04 23:01:22.30: [25957]: SESSION BEGIN 000909911 17027406875
Apr 04 23:01:22.30: [25957]: HylaFAX (tm) Version 4.3.1
Apr 04 23:01:22.30: [25957]: SEND FAX: JOB 832452 DEST 7406875 COMMID
000909911 DEVICE '/dev/ttyIAX-PRI01-07' FROM 'paperclip <paperclip>'
USER paperclip
Apr 04 23:01:22.30: [25957]: STATE CHANGE: RUNNING -> SENDING
Apr 04 23:01:22.30: [25957]: <-- [12:AT+FCLASS=1\r]
Apr 04 23:01:22.30: [25957]: --> [2:OK]
Apr 04 23:01:22.30: [25957]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Apr 04 23:01:22.30: [25957]: DIAL 7406875
Apr 04 23:01:22.30: [25957]: <-- [12:ATDT7406875\r]
Apr 04 23:01:30.92: [25957]: --> [7:CONNECT]
Apr 04 23:01:32.80: [25957]: --> HDLC<32:FF C0 04 00 00 90 00 10 B4 FF
FF FF FF FF FF FF FF FF FF FF FF 80 46 40 50 08 80 40 80 0C CA 7C>
Apr 04 23:01:32.80: [25957]: --> [2:OK]
Apr 04 23:01:32.80: [25957]: REMOTE NSF "00 00 09 00 08 2D FF FF FF FF
FF FF FF FF FF FF FF FF 01 62 02 0A 10 01 02 01 30"
Apr 04 23:01:32.80: [25957]: NSF remote fax equipment: Xerox/Toshiba
Apr 04 23:01:32.80: [25957]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:32.84: [25957]: --> [7:CONNECT]
Apr 04 23:01:33.52: [25957]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04 04 04 A4 F3>
Apr 04 23:01:33.52: [25957]: --> [2:OK]
Apr 04 23:01:33.52: [25957]: REMOTE CSI ""
Apr 04 23:01:33.52: [25957]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:33.56: [25957]: --> [7:CONNECT]
Apr 04 23:01:34.00: [25957]: --> HDLC<15:FF C8 01 00 77 19 23 01 EB C1
01 01 04 AD 72>
Apr 04 23:01:34.12: [25957]: --> [2:OK]
Apr 04 23:01:34.12: [25957]: REMOTE best rate 14400 bit/s
Apr 04 23:01:34.12: [25957]: REMOTE max A4 page width (215 mm)
Apr 04 23:01:34.12: [25957]: REMOTE max unlimited page length
Apr 04 23:01:34.12: [25957]: REMOTE best vres R16 x 15.4 line/mm
Apr 04 23:01:34.12: [25957]: REMOTE format support: MH, MR, MMR, JBIG
Apr 04 23:01:34.12: [25957]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 04 23:01:34.12: [25957]: REMOTE best 5 ms/scanline
Apr 04 23:01:34.12: [25957]: USE 14400 bit/s
Apr 04 23:01:34.12: [25957]: USE error correction mode
Apr 04 23:01:34.12: [25957]: <-- [9:AT+FTH=3\r]
Apr 04 23:01:34.12: [25957]: --> [7:CONNECT]
Apr 04 23:01:34.12: [25957]: <-- HDLC<3:FF C8 DF>
Apr 04 23:01:34.12: [25957]: <-- data [3]
Apr 04 23:01:34.12: [25957]: <-- data [2]
Apr 04 23:01:35.20: [25957]: --> [2:OK]
Apr 04 23:01:35.20: [25957]: MODEM input buffering enabled
Apr 04 23:01:35.20: [25957]: <-- [5:ATH0\r]
Apr 04 23:01:35.32: [25957]: --> [2:OK]
Apr 04 23:01:35.32: [25957]: MODEM set DTR OFF
Apr 04 23:01:35.32: [25957]: MODEM set baud rate: 0 baud (flow control
unchanged)
Apr 04 23:01:35.32: [25957]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Apr 04 23:01:35.32: [25957]: SESSION END
[root@hylafax02 hylafax]# cat log/c000909910
Apr 04 23:01:19.65: [25938]: SESSION BEGIN 000909910 17027361120
Apr 04 23:01:19.65: [25938]: HylaFAX (tm) Version 4.3.1
Apr 04 23:01:19.65: [25938]: SEND FAX: JOB 832450 DEST 7361120 COMMID
000909910 DEVICE '/dev/ttyIAX-PRI01-08' FROM 'paperclip <paperclip>'
USER paperclip
Apr 04 23:01:19.65: [25938]: STATE CHANGE: RUNNING -> SENDING
Apr 04 23:01:19.65: [25938]: <-- [12:AT+FCLASS=1\r]
Apr 04 23:01:19.65: [25938]: --> [2:OK]
Apr 04 23:01:19.65: [25938]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Apr 04 23:01:19.65: [25938]: DIAL 7361120
Apr 04 23:01:19.65: [25938]: <-- [12:ATDT7361120\r]
Apr 04 23:01:36.18: [25938]: --> [7:CONNECT]
Apr 04 23:01:38.14: [25938]: --> HDLC<39:FF C0 04 00 00 8C 04 77 5F 23
01 A9 01 01 01 04 21 B0 BB 00 00 BB BB 00 00 BB BB 00 00 00 00 B7 85 0D
00 00 04 87 0E>
Apr 04 23:01:38.14: [25938]: --> [2:OK]
Apr 04 23:01:38.14: [25938]: REMOTE NSF "00 00 31 20 EE FA C4 80 95 80
80 80 20 84 0D DD 00 00 DD DD 00 00 DD DD 00 00 00 00 ED A1 B0 00 00 20"
Apr 04 23:01:38.14: [25938]: NSF remote fax equipment: Sharp/Olivetti
Apr 04 23:01:38.14: [25938]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:38.86: [25938]: --> [7:CONNECT]
Apr 04 23:01:38.86: [25938]: --> HDLC<25:FF C0 02 0C 4C 8C 8C 6C CC EC
4C 0C EC 04 04 04 04 04 04 04 04 04 04 2E 43>
Apr 04 23:01:38.86: [25938]: --> [2:OK]
Apr 04 23:01:38.86: [25938]: REMOTE CSI "7027361120"
Apr 04 23:01:38.86: [25938]: <-- [9:AT+FRH=3\r]
Apr 04 23:01:39.30: [25938]: --> [7:CONNECT]
Apr 04 23:01:39.30: [25938]: --> HDLC<15:FF C8 01 04 77 5F 23 01 A9 01
01 01 04 90 13>
Apr 04 23:01:39.34: [25938]: --> [2:OK]
Apr 04 23:01:39.34: [25938]: REMOTE best rate 33600 bit/s
Apr 04 23:01:39.34: [25938]: REMOTE max A3 page width (303 mm)
Apr 04 23:01:39.34: [25938]: REMOTE max unlimited page length
Apr 04 23:01:39.34: [25938]: REMOTE best vres R16 x 15.4 line/mm
Apr 04 23:01:39.34: [25938]: REMOTE format support: MH, MR, MMR, JBIG
Apr 04 23:01:39.34: [25938]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 04 23:01:39.34: [25938]: REMOTE best 0 ms/scanline
Apr 04 23:01:39.34: [25938]: USE 9600 bit/s
Apr 04 23:01:39.34: [25938]: USE error correction mode
Apr 04 23:01:39.34: [25938]: <-- [9:AT+FTH=3\r]
Apr 04 23:01:39.35: [25938]: --> [7:CONNECT]
Apr 04 23:01:39.35: [25938]: <-- HDLC<3:FF C8 DF>
Apr 04 23:01:39.35: [25938]: <-- data [3]
Apr 04 23:01:39.36: [25938]: <-- data [2]
Apr 04 23:01:40.43: [25938]: --> [2:OK]
Apr 04 23:01:40.43: [25938]: MODEM input buffering enabled
Apr 04 23:01:40.43: [25938]: <-- [5:ATH0\r]
Apr 04 23:01:40.54: [25938]: --> [2:OK]
Apr 04 23:01:40.54: [25938]: MODEM set DTR OFF
Apr 04 23:01:40.54: [25938]: MODEM set baud rate: 0 baud (flow control
unchanged)
Apr 04 23:01:40.54: [25938]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Apr 04 23:01:40.54: [25938]: SESSION END 

-----Original Message-----
From: Lee Howard [mailto:faxguy@xxxxxxxxxxxxxxxx] 
Sent: Wednesday, April 04, 2007 11:18 PM
To: Dan Brummer
Cc: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] All faxes failing

Dan Brummer wrote:

> I have a very unusual problem.  I run HylaFAX 4.3.1 in a cluster 
> environment using Linux-ha heartbeat.  I use Asterisk+IAXModem for the

> HylaFAX modems.  Out of no where about 95% of all my faxes are 
> failing.  The emails being kicked back give no information (see below 
> for a failed email message).


The actual session log from /var/spoolylafax/log would be most useful.  
The mail message you gave was useless - possibly due to the mail-related
issues in 4.3.1.

Thanks,

Lee.

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*