HylaFAX The world's most advanced open source fax server |
* Fernando <fernando.alhambra@xxxxxxxxx> [070125 12:07]: > Are you meaning this one?: > > [root@vlirofip log]# cat c000000235 > Jan 25 17:53:17.75: [ 6118]: SESSION BEGIN 000000235 34916405075 > Jan 25 17:53:17.75: [ 6118]: HylaFAX (tm) Version 4.3.1 > Jan 25 17:53:17.75: [ 6118]: <-- [4:ATA\r] You've "answered" the phone, HylaFAX is no longer looking for CallID information. If your modem only sends callid after the call is answered, you are going to need to play with: ModemRingResponse So you can "ATA" after then ring, collect the DID information, and then move to "answer" the call. > Jan 25 17:53:17.75: [ 6118]: --> [7:NMBR = ] > Jan 25 17:53:17.75: [ 6118]: --> [16:NDID = 916405008] > Jan 25 17:53:17.75: [ 6118]: --> [4:RING] > Jan 25 17:53:22.61: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:22.61: [ 6118]: RECV FAX: begin > Jan 25 17:53:22.62: [ 6118]: <-- data [32] > Jan 25 17:53:22.62: [ 6118]: <-- data [2] > Jan 25 17:53:24.51: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:24.51: [ 6118]: <-- data [23] > Jan 25 17:53:24.51: [ 6118]: <-- data [2] > Jan 25 17:53:25.23: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:25.23: [ 6118]: <-- data [13] > Jan 25 17:53:25.23: [ 6118]: <-- data [2] > Jan 25 17:53:25.71: [ 6118]: --> [2:OK] > Jan 25 17:53:25.71: [ 6118]: <-- [9:AT+FRH=3\r] > Jan 25 17:53:26.69: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:28.19: [ 6118]: --> [2:OK] > Jan 25 17:53:28.19: [ 6118]: REMOTE TSI "Fax Corporativo" > Jan 25 17:53:28.19: [ 6118]: <-- [9:AT+FRH=3\r] > Jan 25 17:53:28.20: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:28.43: [ 6118]: --> [2:OK] > Jan 25 17:53:28.43: [ 6118]: REMOTE wants 14400 bit/s > Jan 25 17:53:28.43: [ 6118]: REMOTE wants A4 page width (215 mm) > Jan 25 17:53:28.43: [ 6118]: REMOTE wants unlimited page length > Jan 25 17:53:28.43: [ 6118]: REMOTE wants 7.7 line/mm > Jan 25 17:53:28.43: [ 6118]: REMOTE wants 2-D MR > Jan 25 17:53:28.43: [ 6118]: RECV training at v.17 14400 bit/s > Jan 25 17:53:28.43: [ 6118]: <-- [11:AT+FRM=145\r] > Jan 25 17:53:30.21: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:31.70: [ 6118]: RECV: TCF 2715 bytes, 3% non-zero, 2612 > zero-run > Jan 25 17:53:31.70: [ 6118]: --> [10:NO CARRIER] > Jan 25 17:53:31.70: [ 6118]: <-- [9:AT+FRS=7\r] > Jan 25 17:53:31.79: [ 6118]: --> [2:OK] > Jan 25 17:53:31.79: [ 6118]: TRAINING succeeded > Jan 25 17:53:31.80: [ 6118]: <-- [9:AT+FTH=3\r] > Jan 25 17:53:31.80: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:31.80: [ 6118]: <-- data [3] > Jan 25 17:53:31.80: [ 6118]: <-- data [2] > Jan 25 17:53:32.86: [ 6118]: --> [2:OK] > Jan 25 17:53:32.86: [ 6118]: <-- [11:AT+FRM=146\r] > Jan 25 17:53:33.99: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:33.99: [ 6118]: MODEM input buffering enabled > Jan 25 17:53:33.99: [ 6118]: RECV: begin page > Jan 25 17:53:39.36: [ 6118]: RECV: 2188 total lines, 0 bad lines, 0 > consecutive bad lines > Jan 25 17:53:39.36: [ 6118]: RECV: end page > Jan 25 17:53:39.37: [ 6118]: --> [10:NO CARRIER] > Jan 25 17:53:39.37: [ 6118]: <-- [9:AT+FRH=3\r] > Jan 25 17:53:39.77: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:40.64: [ 6118]: --> [2:OK] > Jan 25 17:53:40.64: [ 6118]: RECV recv EOP (no more pages or documents) > Jan 25 17:53:40.64: [ 6118]: <-- [9:AT+FRS=7\r] > Jan 25 17:53:40.83: [ 6118]: --> [2:OK] > Jan 25 17:53:40.85: [ 6118]: <-- [9:AT+FTH=3\r] > Jan 25 17:53:40.95: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:40.95: [ 6118]: <-- data [3] > Jan 25 17:53:40.95: [ 6118]: <-- data [2] > Jan 25 17:53:42.02: [ 6118]: --> [2:OK] > Jan 25 17:53:42.02: [ 6118]: RECV send MCF (message confirmation) > Jan 25 17:53:42.04: [ 6118]: <-- [9:AT+FRH=3\r] > Jan 25 17:53:42.96: [ 6118]: --> [7:CONNECT] > Jan 25 17:53:43.89: [ 6118]: --> [2:OK] > Jan 25 17:53:43.89: [ 6118]: RECV recv DCN (disconnect) > Jan 25 17:53:43.93: [ 6118]: RECV FAX: end > Jan 25 17:53:43.93: [ 6118]: SESSION END a. -- Aidan Van Dyk aidan@xxxxxxxx Senior Software Developer +1 215 825-8700 x8103 iFAX Solutions, Inc. http://www.ifax.com/
Attachment:
signature.asc
Description: Digital signature