[hylafax-users] Re[2]: we reveived bad faxes

[cuneyt <cuneyt@xxxxxxxxxxxxxx>]

Hello Lee,

>>1) hylafax sending faxes very slow with speed: 9600 how can force modem
>>to send faster?

LH> Show me a session log (/var/spool/hylafax/log/).
------------------------------begin of log---------------------------
Dec 14 10:03:45.10: [29064]: SESSION BEGIN 000000026 9024293105804
Dec 14 10:03:45.10: [29064]: HylaFAX (tm) Version 4.3.1
Dec 14 10:03:45.10: [29064]: SEND FAX: JOB 21 DEST 9,3105804 COMMID 000000026 DEVICE '/dev/ttyS0' FROM 'faxuser <cuneyt@xxxxxxxxxxxxxx>' USER faxuser
Dec 14 10:03:45.10: [29064]: <-- [12:AT+FCLASS=1\r]
Dec 14 10:03:45.19: [29064]: --> [2:OK]
Dec 14 10:03:45.19: [29064]: DIAL 9,3105804
Dec 14 10:03:45.19: [29064]: <-- [14:ATDT9,3105804\r]
Dec 14 10:03:58.99: [29064]: --> [7:CONNECT]
Dec 14 10:04:01.03: [29064]: --> [2:OK]
Dec 14 10:04:01.03: [29064]: REMOTE NSF "00 00 0E 00 00 00 96 0F 01 03 00 10 05 02 95 C8 08 01 49 02 45 52 41 59 20 54 4F 55 52 20 4D 55 48 41 53 45 03"
Dec 14 10:04:01.04: [29064]: NSF remote fax equipment: Panasonic KX-F230/KX-FT21
Dec 14 10:04:01.04: [29064]: NSF remote station ID: "ERAY TOUR MUHASE"
Dec 14 10:04:01.04: [29064]: <-- [9:AT+FRH=3\r]
Dec 14 10:04:01.04: [29064]: --> [7:CONNECT]
Dec 14 10:04:01.79: [29064]: --> [2:OK]
Dec 14 10:04:01.79: [29064]: REMOTE CSI "0 242 310 58 04"
Dec 14 10:04:01.79: [29064]: <-- [9:AT+FRH=3\r]
Dec 14 10:04:01.79: [29064]: --> [7:CONNECT]
Dec 14 10:04:02.25: [29064]: --> [2:OK]
Dec 14 10:04:02.25: [29064]: REMOTE best rate 9600 bit/s
Dec 14 10:04:02.25: [29064]: REMOTE max A4 page width (215 mm)
Dec 14 10:04:02.25: [29064]: REMOTE max unlimited page length
Dec 14 10:04:02.25: [29064]: REMOTE best vres 15.4 line/mm
Dec 14 10:04:02.25: [29064]: REMOTE format support: MH, MR
Dec 14 10:04:02.25: [29064]: REMOTE best 20 ms, 10 ms/scanline
Dec 14 10:04:02.25: [29064]: USE 9600 bit/s
Dec 14 10:04:02.25: [29064]: SEND file "docq/doc21.ps;40"
Dec 14 10:04:02.25: [29064]: USE A4 page width (215 mm)
Dec 14 10:04:02.25: [29064]: USE unlimited page length
Dec 14 10:04:02.25: [29064]: USE 3.85 line/mm
Dec 14 10:04:02.25: [29064]: USE 2-D MR
Dec 14 10:04:02.25: [29064]: USE 20 ms/scanline
Dec 14 10:04:02.25: [29064]: SEND training at v.29 9600 bit/s
Dec 14 10:04:02.25: [29064]: DELAY 70 ms
Dec 14 10:04:02.32: [29064]: <-- [9:AT+FTH=3\r]
Dec 14 10:04:02.36: [29064]: --> [7:CONNECT]
Dec 14 10:04:02.36: [29064]: <-- data [23]
Dec 14 10:04:02.36: [29064]: <-- data [2]
Dec 14 10:04:02.37: [29064]: --> [7:CONNECT]
Dec 14 10:04:02.37: [29064]: <-- data [6]
Dec 14 10:04:02.37: [29064]: <-- data [2]
Dec 14 10:04:04.55: [29064]: --> [2:OK]
Dec 14 10:04:04.55: [29064]: DELAY 70 ms
Dec 14 10:04:04.62: [29064]: <-- [10:AT+FTM=96\r]
Dec 14 10:04:05.13: [29064]: --> [7:CONNECT]
Dec 14 10:04:05.13: [29064]: <-- data [1024]
Dec 14 10:04:05.13: [29064]: <-- data [776]
Dec 14 10:04:05.13: [29064]: <-- data [2]
Dec 14 10:04:06.68: [29064]: --> [2:OK]
Dec 14 10:04:06.68: [29064]: <-- [9:AT+FRH=3\r]
Dec 14 10:04:07.28: [29064]: --> [7:CONNECT]
Dec 14 10:04:08.46: [29064]: --> [2:OK]
Dec 14 10:04:08.46: [29064]: TRAINING succeeded
Dec 14 10:04:08.46: [29064]: DELAY 70 ms
Dec 14 10:04:08.53: [29064]: <-- [10:AT+FTM=96\r]
Dec 14 10:04:09.11: [29064]: --> [7:CONNECT]
Dec 14 10:04:09.11: [29064]: SEND begin page
Dec 14 10:04:09.11: [29064]: <-- data [141]
Dec 14 10:04:09.11: [29064]: SENT 141 bytes of data
Dec 14 10:04:09.11: [29064]: <-- data [155]
Dec 14 10:04:09.11: [29064]: SENT 154 bytes of data
Dec 14 10:04:09.11: [29064]: <-- data [122]
......*here continue to show sent bytes of data*........
Dec 14 10:04:33.47: [29064]: SENT 144 bytes of data
Dec 14 10:04:33.47: [29064]: <-- data [48]
Dec 14 10:04:33.47: [29064]: SENT 48 bytes of data
Dec 14 10:04:33.47: [29064]: SEND 2D RTC
Dec 14 10:04:33.47: [29064]: <-- data [30]
Dec 14 10:04:33.47: [29064]: <-- data [2]
Dec 14 10:04:33.47: [29064]: SEND end page
Dec 14 10:04:37.39: [29064]: --> [2:OK]
Dec 14 10:04:37.39: [29064]: DELAY 90 ms
Dec 14 10:04:37.48: [29064]: SEND send EOP (no more pages or documents)
Dec 14 10:04:37.49: [29064]: <-- [9:AT+FTH=3\r]
Dec 14 10:04:37.52: [29064]: --> [7:CONNECT]
Dec 14 10:04:37.53: [29064]: <-- data [3]
Dec 14 10:04:37.53: [29064]: <-- data [2]
Dec 14 10:04:38.84: [29064]: --> [2:OK]
Dec 14 10:04:38.84: [29064]: <-- [9:AT+FRH=3\r]
Dec 14 10:04:39.52: [29064]: --> [7:CONNECT]
Dec 14 10:04:40.70: [29064]: --> [2:OK]
Dec 14 10:04:40.70: [29064]: SEND recv MCF (message confirmation)
Dec 14 10:04:40.70: [29064]: SEND FAX (000000026): FROM cuneyt@xxxxxxxxxxxxxx TO 9,3105804 (page 1 of 1 sent in 0:38)
Dec 14 10:04:40.70: [29064]: DELAY 70 ms
Dec 14 10:04:40.77: [29064]: SEND FAX (000000026): FROM cuneyt@xxxxxxxxxxxxxx TO 9,3105804 (docq/doc21.ps;40 sent in 0:38)
Dec 14 10:04:41.70: [29064]: <-- [9:AT+FTH=3\r]
Dec 14 10:04:41.75: [29064]: --> [7:CONNECT]
Dec 14 10:04:41.75: [29064]: <-- data [3]
Dec 14 10:04:41.75: [29064]: <-- data [2]
Dec 14 10:04:43.05: [29064]: --> [2:OK]
Dec 14 10:04:43.05: [29064]: <-- [5:ATH0\r]
Dec 14 10:04:43.48: [29064]: --> [10:NO CARRIER]
Dec 14 10:04:43.48: [29064]: MODEM No carrier
Dec 14 10:04:43.48: [29064]: SESSION END
------------------------------end of log-----------------------

>>2)
LH> Do you not want HylaFAX to send any notification mails at all?  This
LH> would seem a bit odd.  Let me know what you're really trying to accomplish.

no i want to hylafax send mail to users. but this mail adress upthere
is wrong and no user with this mail adress, i use "whfc hylafax
client" and i got 2 users and no user with this email adres but hylafax everytime
trying to send mail to this adress: cuneyt@xxxxxxxxxxx
when i installed hylafax client firstime just typed wrong mail
adresses and now nobody not use this mail adreses why hylafax
trying to send mail to this adresess?
here another mail adres "arge@xxxxxxxxxxxxxx" which doesn't exist.
--------- start of log--------------------------------------------------------------
Dec 14 10:17:59 linux-rves postfix/qmgr[3911]: 3DAAB82F: from=<fax@xxxxxxxxxxxxxxx>, size=403, nrcpt=1 (queue active)
Dec 14 10:18:00 linux-rves postfix/smtp[29438]: 3DAAB82F: host mail.teztour.com.tr[212.175.193.222]
said: 450 4.1.1 <arge@xxxxxxxxxxxxxx>: Recipient address rejected: User unknown in local recipient table (in reply to RCPT TO command)
Dec 14 10:18:00 linux-rves postfix/smtp[29438]: 3DAAB82F: to=<arge@xxxxxxxxxxxxxx>, relay=mail.teztour.com.tr[81.21.161.141], delay=432044, status=deferred (host mail.teztour.com.tr[81.21.161.141] said: 450 4.1.1 <arge@xxxxxxxxxxxxxx>: Recipient address rejected: User unknown in local recipient table (in reply to RCPT TO command))
Dec 14 10:18:00 linux-rves postfix/qmgr[3911]: 3DAAB82F: from=<fax@xxxxxxxxxxxxxxx>, status=expired, returned to sender
Dec 14 10:18:00 linux-rves postfix/cleanup[29441]: 9D26138914: message-id=<20061214081800.9D26138914@xxxxxxxxxxxxxxx>
Dec 14 10:18:00 linux-rves postfix/qmgr[3911]: 9D26138914: from=<>, size=2338, nrcpt=1 (queue active)
Dec 14 10:18:00 linux-rves postfix/qmgr[3911]: 3DAAB82F: removed
Dec 14 10:18:01 linux-rves postfix/local[29442]: 9D26138914: to=<fax@xxxxxxxxxxxxxxx>, relay=local,
delay=1, status=sent (delivered to mailbox)
Dec 14 10:18:01 linux-rves postfix/qmgr[3911]: 9D26138914: removed
Dec 14 10:23:29 linux-rves master[29468]: about to exec /usr/lib/cyrus/bin/ctl_cyrusdb
Dec 14 10:23:29 linux-rves ctl_cyrusdb[29468]: checkpointing cyrus databases
Dec 14 10:23:29 linux-rves ctl_cyrusdb[29468]: archiving database file: /var/lib/imap/annotations.dbDec 14 10:23:29 linux-rves ctl_cyrusdb[29468]: archiving log file: /var/lib/imap/db/log.0000000001
Dec 14 10:23:29 linux-rves ctl_cyrusdb[29468]: archiving database file: /var/lib/imap/mailboxes.db
Dec 14 10:23:29 linux-rves ctl_cyrusdb[29468]: archiving log file: /var/lib/imap/db/log.0000000001
Dec 14 10:23:29 linux-rves ctl_cyrusdb[29468]: done checkpointing cyrus databases
----------------end of log--------------------------------------------------------
i just want to stop hylafax to trying to send mail to this wrong
adresses.

>>3)

LH> Yes, in your FaxDispatch file just set SENDTO based on $DEVICE.  See:

LH>    http://hylafax.sourceforge.net/man/faxrcvd.php

LH> Lee.

im now trying to give users their own lines. thank you for all.
Best regards,
Cuneyt


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*