Re: [hylafax-users] 3com u.s. robotics 5

[bill.allison@xxxxxxxxx]

Hello

Unfortunately I have no experience of using USR modems in Class 2.0.   
Others on the list will be much more competent than I to take it from   
here. Only suggestion I have is try using Class 1 - I do recall someone   
here saying that the USRs are problematic in Class 2.0

In case it helps here is my config for a similar modem 245630-02

=============================================
FAXNumber:              +44.01remainder concealed
LongDistancePrefix:     ""
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         3
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0600
RingsBeforeAnswer:      3
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "BSW Timber (Group HQ - Earlston)"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "     From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
CIDNumber:              "NMBR = "

#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
# Temporary addition of ATS6=4 (delay b4 dialling) for BCM autodial of 9
ModemResetCmds:         AT#CID=1S6=4
ModemType:              Class1          # use class 1 interface
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       RTSCTS
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier   
(or not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow   
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow   
control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow   
control
Class1SFLOCmd:          ""              # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for   
response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:            AT+FNR=1,1,1,0
# Below at Lee Howard's suggestion, to overcome USR 5630 resets during   
MCF
Class1SwitchingCmd:     "<delay:7>"     # silence between HDLC recv and   
trans
======================================

Regards
Bill A.

 -----Original Message-----
From: mauro.sanna@xxxxxxxxxxxxxxxxxx
Sent: 14 November 2006 12:29
To: Bill Allison
Cc: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] 3com u.s. robotics 5


   

 --------------------------------------------------------------------------  
 --
> I can probably help if your problem is with the settings for this   
modem,
> but your session log indicates there is something wrong with the number   
    

> given to hylafax to dial, and others on the list will be more able than   
I
> to suggest where that's gone wrong (with the client?)
>
> Where your log shows "DIAL ??? # number" I would have expected it to   
say
> "DIAL 8441" as per the 3rd line of your log. I suspect the problem is   
    

> with the client or how you are using it. How are you sending the fax -   
    

> using sendfax within a script or using a client of some sort? If the
> former let us see the script. Might be useful to post doneq/q11.


Here is the complete session log:

nov 14 13:20:25.86: [ 4356]: SESSION BEGIN 000000066 00390708441
nov 14 13:20:25.86: [ 4356]: HylaFAX (tm) Version 4.2.1
nov 14 13:20:25.86: [ 4356]: SEND FAX: JOB 14 DEST 8441 COMMID 000000066
DEVICE
'/dev/ttyS0'
nov 14 13:20:25.86: [ 4356]: <-- [9:AT+FLO=2\r]
nov 14 13:20:26.11: [ 4356]: --> [2:OK]
nov 14 13:20:26.11: [ 4356]: <-- [9:AT+FPP=0\r]
nov 14 13:20:26.36: [ 4356]: --> [2:OK]
nov 14 13:20:26.36: [ 4356]: <-- [9:AT+FBO=0\r]
nov 14 13:20:26.61: [ 4356]: --> [2:OK]
nov 14 13:20:26.61: [ 4356]: <-- [10:AT+FCT=30\r]
nov 14 13:20:26.86: [ 4356]: --> [2:OK]
nov 14 13:20:26.86: [ 4356]: <-- [15:AT+FNR=1,1,1,0\r]
nov 14 13:20:27.11: [ 4356]: --> [2:OK]
nov 14 13:20:27.11: [ 4356]: <-- [9:AT+FIE=0\r]
nov 14 13:20:27.36: [ 4356]: --> [2:OK]
nov 14 13:20:27.36: [ 4356]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
nov 14 13:20:27.62: [ 4356]: --> [2:OK]
nov 14 13:20:27.62: [ 4356]: DIAL 8441
nov 14 13:20:27.62: [ 4356]: <-- [9:ATDT8441\r]
nov 14 13:20:42.71: [ 4356]: --> [4:+FCO]
nov 14 13:20:46.00: [ 4356]: --> [27:+FCI:"          0706778441"]
nov 14 13:20:46.00: [ 4356]: REMOTE CSI "0706778441"
nov 14 13:20:46.00: [ 4356]: --> [20:+FIS:1,5,0,2,1,0,0,3]
nov 14 13:20:46.00: [ 4356]: --> [2:OK]
nov 14 13:20:46.00: [ 4356]: REMOTE best rate 14400 bit/s
nov 14 13:20:46.00: [ 4356]: REMOTE max A4 page width (215 mm)
nov 14 13:20:46.00: [ 4356]: REMOTE max unlimited page length
nov 14 13:20:46.00: [ 4356]: REMOTE best vres 7.7 line/mm
nov 14 13:20:46.00: [ 4356]: REMOTE best format 2-D MR
nov 14 13:20:46.00: [ 4356]: REMOTE best 10 ms/scanline
nov 14 13:20:46.00: [ 4356]: USE 14400 bit/s
nov 14 13:20:46.00: [ 4356]: USE 10 ms/scanline
nov 14 13:20:46.00: [ 4356]: <-- [5:ATH0\r]
nov 14 13:20:46.25: [ 4356]: --> [2:OK]
nov 14 13:20:46.25: [ 4356]: SESSION END

it says:

  FaxQueuer[4330]: NOTIFY: bin/notify "doneq/q14" "failed" "0:36"
Nov 14 13:20:46 fax1 FaxQueuer[4330]: NOTIFY exit status: 0 (4358)

I can't get where is the problem.
With another modem I can send faxes without any problem.
With this Robotic is a problem.
Here is my configuration:

ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              9600            # DCE-DTE communication rate
ModemFlowControl:       rtscts          # hardware flow control
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)
ModemResultCodesCmd:    ATQ0X4          # enable extended result codes
#
ModemSetupAACmd:        AT+FAA=1

ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
#

Class2BUGCmd:           AT+FBU=0
#
#
Class2CQQueryCmd:       !(0),(0)        # override modem response
#
#
Class2NRCmd:    AT+FNR=1,1,1,0

Class2SendRTC:  yes
#
Class2APQueryCmd:       none

____________________ HylaFAX(tm) Users Mailing List   
_______________________
  To subscribe/unsubscribe, click   
http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <   
/dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*


 --
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*