Re: [hylafax-users] Hylafax - Iaxmodem - send fax - Asterisk

["Duncan Turnbull" <duncan@xxxxxxxxxxxxxx>]

I send about 700 different faxes over 8 hours using two lines going constantly - no issues with that. 

Its not 8 lines but it is a bit of a work out for iaxmodem hylafax and asterisk

Cheers Duncan

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Ma Zhiyong
Sent: Friday, 25 August 2006 3:50 p.m.
To: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] Hylafax - Iaxmodem - send fax - Asterisk

hylafax+iaxmodem is a good solution for some flexible applications.
But I didn't think spandsp can well support concurrent fax calls in
one box. Did any one has experience to send more than 8 fax to
different destinations at the same time by iaxmodem?

2006/8/25, Colin Anderson <ColinA@xxxxxxxxxxxxxxxxxxxxxxxxx>:
> 4 things:
>
> 1. The password does not match
>
> 2. The authentication type does not match i.e. you have specified auth=md5
> in iax.conf when the password is passed in plaintext
>
> 3. host=dynamic or host=IP address of IAX modem, must be explicitly set
>
> 4. Typo in iax.conf, I do it all the time.
>
> -----Original Message-----
> From: Joshua Nunn [mailto:jnunn@xxxxxxxxxxxx]
> Sent: Thursday, August 24, 2006 3:29 PM
> To: hylafax-users@xxxxxxxxxxx
> Subject: Re: [hylafax-users] Hylafax - Iaxmodem - send fax - Asterisk
>
>
> IAXModem on the command line gives me this.
> =====================
> cytrex3 mercestes # iaxmodem ttyIAX0
> [2006-08-24 16:28:45] Modem started
> [2006-08-24 16:28:45] Setting device = '/dev/ttyIAX0'
> [2006-08-24 16:28:45] Setting owner = 'uucp:uucp'
> [2006-08-24 16:28:45] Setting mode = '660'
> [2006-08-24 16:28:45] Setting port = 4571
> [2006-08-24 16:28:45] Setting refresh = 300
> [2006-08-24 16:28:45] Setting server = '216.54.143.19'
> [2006-08-24 16:28:45] Setting peername = 'iaxmodem1'
> [2006-08-24 16:28:45] Setting secret = 'my_super_secret'
> [2006-08-24 16:28:45] Setting cidname = 'John Doe'
> [2006-08-24 16:28:45] Setting cidnumber = '8005551212'
> [2006-08-24 16:28:45] Setting codec = slinear
> [2006-08-24 16:28:45] Opened pty, slave device: /dev/pts/12
> [2006-08-24 16:28:45] Created /dev/ttyIAX0 symbolic link
> [2006-08-24 16:28:45] Registration completed successfully.
> ====================================
>
> IAX debug gives me this.
>
> =============================
> Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX     Subclass: NEW
>   Timestamp: 00003ms  SCall: 06886  DCall: 00000 [216.54.143.19:33228]
>   VERSION         : 2
>   CALLING NUMBER  : 8005551212
>   CALLING NAME    : John Doe
>   FORMAT          : 64
>   CAPABILITY      : 76
>   USERNAME        : iaxmodem4
>   CALLED NUMBER   : 2819870065
>   DNID            : 2819870065
>
> Tx-Frame Retry[000] -- OSeqno: 000 ISeqno: 001 Type: IAX     Subclass:
> REJECT
>   Timestamp: 00008ms  SCall: 00001  DCall: 06886 [216.54.143.19:33228]
>   CAUSE           : No authority found
>   CAUSE CODE      : 50
>
> Rx-Frame Retry[ No] -- OSeqno: 001 ISeqno: 001 Type: IAX     Subclass: ACK
>   Timestamp: 00008ms  SCall: 06886  DCall: 00001 [216.54.143.19:33228]
> ====================================
>
> So I'm getting to my box and * is rejecting me on a cause 50 ("No
> Authority").
>
>  Any clues what that means??
>
> Joshua Nunn
>  Network Manager
>  Cypress Telecommunications
>  ----- Original Message -----
> From: "Lee Howard" <faxguy@xxxxxxxxxxxxxxxx>
> To: "Joshua Nunn" <jnunn@xxxxxxxxxxxx>
> Cc: <hylafax-users@xxxxxxxxxxx>
> Sent: Thursday, August 24, 2006 4:21 PM
> Subject: Re: [hylafax-users] Hylafax - Iaxmodem - send fax - Asterisk
>
>
> > Joshua Nunn wrote:
> >
> > >   Is there a wiki or tutorial on how to set up hylafax, Iaxmodem and
> > > Asterisk to use the hylafax sendfax command to send a fax through
> > > asterisk via the IAXmodem??
> >
> >
> > Just the documentation that comes with the source code and what's on the
> > sourceforge websites.
> >
> > >   I keep getting a no dial tone back but I have a _X. rule in my
> > > IAXmodem context in *, so I don't think it's rejecting.
> >
> >
> > Run iaxmodem from the command-line ... maybe that will reveal something
> > in the output there.  If that doesn't work, then you'll probably need to
> > turn on iax2 debugging (edit iaxmodem.c ... search for "debug"... then
> > rebuild).
> >
> > Lee.
> >
> > ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> >   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null
> >   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
> >
> >
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>
>

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*