Re: [hylafax-users] Configure mainpine quattro+ on suse

["joea (joea@xxxxxxxxxxxxxxx)" <joea@xxxxxxxxxxxxxxx>]

This morning, after a cold boot, I come back with none found as 
shown below:
******************************************* 
FS2-L:~ # wvdialconf modemtest 
Scanning your serial ports for a modem. 
 
ircomm4<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm5<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm6<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm7<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm8<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm9<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm10<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm11<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm14<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm15<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
ircomm16<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud. 
************************************************** 

When I do the steps shown on your web page, I get a response
that suggests this is an "older revision" board, although just
purchased brand new.

The link to instructions for that board give a "404" error.

I sent this info to the support address.

I did get an indiaction, last evening, that the first port was ttyS14, when 
running "wvdialconf modemtest", after having made some attempts at
configuring.    I did not bother saving the setserial commands, as they
did not seem to be working 100%.

joea

Support<support@xxxxxxxxxxxx> Boldly Declared: 5/19/2006 7:07 PM:
>  
> You can find out what ttyS number was assigned to the first port of the
> Mainpine board by running this from a command prompt:
> 
> wvdialconf modemtest
> 
> After you get the first ttyS#, you can proceed with the Mainpine
> installation instructions located here:
> 
> http://www.mainpine.com/faqs/linux_ans/ans1_linux.htm 
> 
> This will help you configure your rc.serial  file with the correct
> setserial commands.
> 
> Note:  If you are running a Linux 2.6.x kernel version, you cannot add
> the setserial line with the "set_multiport" setting.  Leave that last
> line out when you are adding your configuration lines to the rc.serial
> file.  That setting is not required for 2.6.x kernel systems.
> 
> If you still have problems, you may contact our support department
> directly at support@xxxxxxxxxxxx .
> 
> Thank you,
> 
> Derrek Sypert
> Mainpine, Inc. Support Manager
> USA +1 718 701 2422 | Asia/Europe +44 1225 436137 
> derrek.sypert@xxxxxxxxxxxx | www.mainpine.com 
> 
> -----Original Message-----
> From: hylafax-users-bounce@xxxxxxxxxxx 
> [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of joea
> Sent: Friday, May 19, 2006 3:37 PM
> To: hylafax-users@xxxxxxxxxxx 
> Subject: Re: [hylafax-users] Configure mainpine quattro+ on suse
> 
> So, muddling my way,  have defined the serial ports (as ttyS4-ttyS7),
> but get a "UART unknown" when doing a "setserial".  The rest of the
> output seems reasonable.
> 
> How can I tell it what the UART is.  And how would I know?
> 
> joea
> 
> joea<joea@xxxxxxxxxxxxxxx> Boldly Declared: 5/19/2006 5:54 PM:
>> Need to configure mainpine quattro+ on sles 9 with hylafax 4.2.5
>> 
>> Found specifics for RH (geeky) and Fedora (magic).  YAST on Suse does 
>> not seem to fit the bill, expect geekness to intrude.  Docs,
> somewhere?
>> 
>> joea
>> 
>> ____________________ HylaFAX(tm) Users Mailing List 
>> _______________________
>>   To subscribe/unsubscribe, click
>> http://lists.hylafax.org/cgi-bin/lsg2.cgi 
>>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
>> /dev/null
>>   *To learn about commercial HylaFAX(tm) support, mail 
>> sales@xxxxxxxxx* 
> 
> 
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
>   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi 
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx* 


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*