Re: [hylafax-users] Rockforce Quadro+ - 1 port hangs

[Anton Karpov <anton@xxxxxxxxx>]

Andrew
After reboot all 4 ports are back to "Running and idle".

I've called today Mainpine , did I talk to you or someone else?
Should I fill out the form on the site and/or start RMA process?

Anton

Andrew Rinaldi wrote:
> Hi Anton.
>
> What happens if you power cycle the server ? 
>
> Regards
>
> ANDREW RINALDI
> Mainpine Support
> USA +1 718 701 2422 | Asia/Europe +44 1225 436137 
> andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com
>
> -----Original Message-----
> From: hylafax-users-bounce@xxxxxxxxxxx
> [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Anton Karpov
> Sent: 03 February 2006 11:24
> To: hylafax-users@xxxxxxxxxxx
> Subject: [hylafax-users] Rockforce Quadro+ - 1 port hangs
>
> Hello
> I have Rockforce Quadro+ working with 4 ports configured for 
> Hylafax+faxgetty incoming only.
> Hylafax 4.2.5 on Gentoo, Kernel 2.6.14.1 For about 3 days everything worked
> fine , then port #1 ( ttyS4)  hung . 
> The rest of the ports work fine.
>
> If I restart faxgetty I get "Waiting for the modem to come ready" and then
> "Initializing server" on port 1, while 3 other ports are "Running and idle"
>
> Right when the port #1 hung there is an unusual log.
> Right after this log the port #1 does not respond anymore, while port #2 ,
> 3,  4 work fine.
>
> Could anyone tell me if this a hardware or software issue?
>
> Feb 02 10:05:25.21: [ 8085]: SESSION BEGIN 000000125 19529282279 Feb 02
> 10:05:25.21: [ 8085]: HylaFAX (tm) Version 4.2.5 Feb 02 10:05:25.21: [
> 8085]: <-- [4:ATA\r] Feb 02 10:05:37.99: [ 8085]: --> [7:CONNECT] Feb 02
> 10:05:37.99: [ 8085]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS4'
> Feb 02 10:05:37.99: [ 8085]: RECV FAX: begin Feb 02 10:05:37.99: [ 8085]:
> <-- data [32] Feb 02 10:05:37.99: [ 8085]: <-- data [2] Feb 02 10:05:38.00:
> [ 8085]: --> [7:CONNECT] Feb 02 10:05:38.00: [ 8085]: <-- data [23] Feb 02
> 10:05:38.00: [ 8085]: <-- data [2] Feb 02 10:05:38.00: [ 8085]: -->
> [7:CONNECT] Feb 02 10:05:38.00: [ 8085]: <-- data [13] Feb 02 10:05:38.00: [
> 8085]: <-- data [2] Feb 02 10:05:40.22: [ 8085]: --> [2:OK] Feb 02
> 10:05:40.22: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:05:40.60: [ 8085]: -->
> [7:CONNECT] Feb 02 10:05:42.22: [ 8085]: --> [2:OK] Feb 02 10:05:42.22: [
> 8085]: REMOTE TSI "7153590948"
> Feb 02 10:05:42.22: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:05:42.24: [ 8085]:
> --> [7:CONNECT] Feb 02 10:05:42.61: [ 8085]: --> [2:OK] Feb 02 10:05:42.61:
> [ 8085]: REMOTE wants 14400 bit/s Feb 02 10:05:42.61: [ 8085]: REMOTE wants
> A4 page width (215 mm) Feb 02 10:05:42.61: [ 8085]: REMOTE wants unlimited
> page length Feb 02 10:05:42.61: [ 8085]: REMOTE wants 7.7 line/mm Feb 02
> 10:05:42.61: [ 8085]: REMOTE wants 1-D MH Feb 02 10:05:42.61: [ 8085]: RECV
> training at v.17 14400 bit/s Feb 02 10:05:42.61: [ 8085]: <--
> [11:AT+FRM=145\r] Feb 02 10:05:44.23: [ 8085]: --> [7:CONNECT] Feb 02
> 10:05:45.70: [ 8085]: RECV: TCF 2656 bytes, 6% non-zero, 823 zero-run Feb 02
> 10:05:45.70: [ 8085]: RECV: reject TCF (zero run too short, min 1800) Feb 02
> 10:05:45.70: [ 8085]: --> [10:NO CARRIER] Feb 02 10:05:45.70: [ 8085]: <--
> [9:AT+FRS=7\r] Feb 02 10:05:45.78: [ 8085]: --> [2:OK] Feb 02 10:05:45.78: [
> 8085]: <-- [9:AT+FTH=3\r] Feb 02 10:05:46.64: [ 8085]: --> [7:CONNECT] Feb
> 02 10:05:46.64: [ 8085]: <-- data [3] Feb 02 10:05:46.64: [ 8085]: <-- data
> [2] Feb 02 10:05:46.97: [ 8085]: --> [2:OK] Feb 02 10:05:46.97: [ 8085]:
> TRAINING failed Feb 02 10:05:46.97: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02
> 10:05:47.31: [ 8085]: --> [7:CONNECT] Feb 02 10:05:48.60: [ 8085]: -->
> [10:NO CARRIER] Feb 02 10:05:48.60: [ 8085]: MODEM No carrier Feb 02
> 10:05:48.60: [ 8085]: <-- [9:AT+FRS=7\r] Feb 02 10:05:48.68: [ 8085]: -->
> [2:OK] Feb 02 10:05:48.68: [ 8085]: <-- [9:AT+FTH=3\r] Feb 02 10:05:49.54: [
> 8085]: --> [7:CONNECT] Feb 02 10:05:49.54: [ 8085]: <-- data [3] Feb 02
> 10:05:49.54: [ 8085]: <-- data [2] Feb 02 10:05:49.86: [ 8085]: --> [2:OK]
> Feb 02 10:05:49.86: [ 8085]: RECV send CRP (command repeat) Feb 02
> 10:05:49.86: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:05:50.32: [ 8085]: -->
> [7:CONNECT] Feb 02 10:05:51.59: [ 8085]: --> [10:NO CARRIER] Feb 02
> 10:05:51.59: [ 8085]: MODEM No carrier Feb 02 10:05:51.59: [ 8085]: <--
> [9:AT+FRS=7\r] Feb 02 10:05:51.67: [ 8085]: --> [2:OK] Feb 02 10:05:51.67: [
> 8085]: <-- [9:AT+FTH=3\r] Feb 02 10:05:52.54: [ 8085]: --> [7:CONNECT] Feb
> 02 10:05:52.54: [ 8085]: <-- data [3] Feb 02 10:05:52.54: [ 8085]: <-- data
> [2] Feb 02 10:05:52.86: [ 8085]: --> [2:OK] Feb 02 10:05:52.86: [ 8085]:
> RECV send CRP (command repeat) Feb 02 10:05:52.86: [ 8085]: <--
> [9:AT+FRH=3\r] Feb 02 10:05:59.86: [ 8085]: --> [0:] Feb 02 10:05:59.86: [
> 8085]: MODEM <Empty line> Feb 02 10:05:59.86: [ 8085]: <-- data [1] Feb 02
> 10:05:59.87: [ 8085]: --> [2:] Feb 02 10:05:59.87: [ 8085]: --> [2:OK] Feb
> 02 10:05:59.87: [ 8085]: DELAY 1500 ms Feb 02 10:06:01.37: [ 8085]: <--
> [9:AT+FTH=3\r] Feb 02 10:06:02.23: [ 8085]: --> [7:CONNECT] Feb 02
> 10:06:02.23: [ 8085]: <-- data [32] Feb 02 10:06:02.23: [ 8085]: <-- data
> [2] Feb 02 10:06:02.24: [ 8085]: --> [7:CONNECT] Feb 02 10:06:02.24: [
> 8085]: <-- data [23] Feb 02 10:06:02.24: [ 8085]: <-- data [2] Feb 02
> 10:06:02.24: [ 8085]: --> [7:CONNECT] Feb 02 10:06:02.24: [ 8085]: <-- data
> [13] Feb 02 10:06:02.24: [ 8085]: <-- data [2] Feb 02 10:06:04.46: [ 8085]:
> --> [2:OK] Feb 02 10:06:04.46: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02
> 10:06:11.47: [ 8085]: --> [0:] Feb 02 10:06:11.47: [ 8085]: MODEM <Empty
> line> Feb 02 10:06:11.47: [ 8085]: <-- data [1] Feb 02 10:06:11.48: [ 8085]:
> --> [2:] Feb 02 10:06:11.48: [ 8085]: --> [2:OK] Feb 02 10:06:11.48: [
> 8085]: DELAY 1500 ms Feb 02 10:06:12.98: [ 8085]: <-- [9:AT+FTH=3\r] Feb 02
> 10:06:13.84: [ 8085]: --> [7:CONNECT] Feb 02 10:06:13.84: [ 8085]: <-- data
> [32] Feb 02 10:06:13.84: [ 8085]: <-- data [2] Feb 02 10:06:13.85: [ 8085]:
> --> [7:CONNECT] Feb 02 10:06:13.85: [ 8085]: <-- data [23] Feb 02
> 10:06:13.85: [ 8085]: <-- data [2] Feb 02 10:06:13.85: [ 8085]: -->
> [7:CONNECT] Feb 02 10:06:13.85: [ 8085]: <-- data [13] Feb 02 10:06:13.85: [
> 8085]: <-- data [2] Feb 02 10:06:16.07: [ 8085]: --> [2:OK] Feb 02
> 10:06:16.07: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:06:23.08: [ 8085]: -->
> [0:] Feb 02 10:06:23.08: [ 8085]: MODEM <Empty line> Feb 02 10:06:23.08: [
> 8085]: <-- data [1] Feb 02 10:06:23.09: [ 8085]: --> [2:] Feb 02
> 10:06:23.09: [ 8085]: --> [2:OK] Feb 02 10:06:23.09: [ 8085]: RECV FAX:
> Failure to train modems Feb 02 10:06:23.09: [ 8085]: RECV FAX: end Feb 02
> 10:06:23.09: [ 8085]: SESSION END
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>   To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>   To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>
>
>   


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*