[hylafax-users] "Busy Signal detected" with Eicon Diva 4BRI

[Carlo Farinella <alert@xxxxxxxxxx>]

Hi all,

i've got a problem with my Eicon Diva 4BRI with outbound faxes.

The command i used is: sendfax -T 1 -n -d $NUMBER  $FILENAME
and my log reports:

Oct 12 17:54:59 fax FaxSend[14695]: MODEM ISDN4LINUX isdn4linux/Rev: 1.1.4.1
Oct 12 17:54:59 fax FaxSend[14695]: SEND FAX: JOB 16 DEST $NUMBER COMMID 
000000067 DEVICE '/dev/ttyI0'
Oct 12 17:54:59 fax kernel: isdn: diva0,ch0 cause: E013b
Oct 12 17:54:59 fax FaxSend[14695]: SEND FAILED: JOB 16 DEST $NUMBER ERR 
Busy signal detected
Oct 12 17:55:00 fax FaxQueuer[14681]: NOTIFY exit status: 0 (14697)

The fax server is correctly working, i can receive fax from all my 
TTYIx, the problem is only with outbound faxes. I've also had a test 
with an isdn phone just to test the lines are. I think the problem is in 
the initialising string, but i've not found any interesting (or working) 
parameters, could you help me?

Thanks in advance

Here's my main settings in TTYI0.cfg.

ModemType:              Class2          # use this to supply a hint
#ModemRate:             19200           # max rate for DCE-DTE communication
#ModemFlowControl:      xonxoff         # XON/XOFF flow control assumed
#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
#ModemSetupDCDCmd:      AT&C1           # setup so DCD reflects carrier 
(or not)
ModemDialCmd:           ATDT%s          # T for tone dialing
ModemResetCmds:         "AT&E710"               # stuff to do when modem 
is reset
#ModemAnswerCmd:                ATA             # use this to answer phone
#ModemNoFlowCmd:                AT&K            # disable flow control cmd
#ModemHardFlowCmd:      AT&K3           # hardware flow control cmd
#ModemSoftFlowCmd:      AT&K4           # software flow control cmd
#ModemNoAutoAnswerCmd:  ATS0=0          # disable auto-answer
Class2Cmd:              AT+FCLASS=2     # command to enter class 2
Class2BORCmd:           AT+FBOR=0       # bit order for phase B/C/D (direct)
Class2RELCmd:           AT+FREL=1       # byte-align EOL codes on recv
Class2CQCmd:            ""              # commands to enable copy 
quality proc.
Class2AbortCmd:         AT+FK           # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality 
capabilities
Class2DCCQueryCmd:      AT+FDCC=?       # query for modem capabilities
Class2TBCCmd:           AT+FTBC=0       # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FPHCTO=30    # set phase C timeout parameter
Class2BUGCmd:           AT+FBUG=1       # enable HDLC frame tracing
Class2LIDCmd:           AT+FLID         # set local identifier command
Class2DCCCmd:           AT+FDCC         # set modem capabilities command
Class2DISCmd:           AT+FDIS         # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FCIG         # set polling identifier command
Class2PTSCmd:           AT+FPTS         # set post-page status command
#Class2SPLCmd:          AT+FSPL         # set polling indicator command
Class2RecvDataTrigger:  ""              # character sent to modem to 
start recv
Class2XmitWaitForXON:   yes             # if true, wait for XON before send


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*