[hylafax-users] Problem with Hylafax and Eicon Diva 4BRI-8M

[alert@xxxxxxxxxx]

Hi all,
i'm trying to setup the a Eicon Diva 4BRI-8M card on my slackware linux,
from the driver by Melware (not capi).

I've recompiled my 2.4 kernel and loaded the firmware (divactrl load -c
1 -f ETSI), as u can see from divactrl log it's all ok, now the leds are on.
Now i've installed hylafax from the cvs, i think that the correct
interface is ttyI*....  but when i run faxaddmodem it report me a modem class error, please see log again.

I looked into all hylafax ml post but i've not found the solution to my
problem. It seems that it can't recognize the modem class, i've tried
several config.ttyI0 but nothing of them resolved the problem, and i'm
not sure that a right conf can help me. Anyway, my conf is the same
reported in this post:
http://groups.google.it/group/fa.hylafax/browse_frm/thread/5474182538d4b5e5/be6888184686f118?q=4BRI+hylafax&rnum=4&hl=it#be6888184686f118

Can somebody help me? Greetings

Carlos


The problem in faxaddmodem (devices ttyI0)
------------------------------------------------------------------
Now we are going to probe the tty port to figure out the type
of modem that is attached.  This takes a few seconds, so be patient.
Note that if you do not have the modem cabled to the port, or the
modem is turned off, this may hang (just go and cable up the modem
or turn it on, or whatever).

Probing for best speed to talk to modem: 38400 OK.

The result of the AT+FCLASS=? command was:

ATQ0V1E1
OK
AT+FCLASS=?
ERROR

We were unable to deduce what type of modem you have.  This means that
it did not respond as a Class 1, Class 2, or Class 2.0 modem should.
If you believe that your modem conforms to the Class 1, Class 2, or
Class 2.0 interface specification, then check that the modem is
operating properly and that you can communicate with the modem from the
host.  If your modem is not one of the above types of modems, then this
software does not support it and you will need to write a driver that
supports it.
------------------------------------------------------------------




root@test:~# divactrl load -c 1 -f ETSI -Debug
Start adapter Nr:1 - 'Diva Server 4BRI-8M 2.0 PCI', SN: 19579 ...

FPGA[] file ds4bri2.bit (2002/02/21    10:52:08 10:52:08) len 233649
Loading TE_DMLT, Build 104-785, Protocol 6.03 104-859 [F#00FF]
3: DSP code base 0x80dd4c60, max size 0x0021b3a0 (80dd4c60,80)
Download addr 0x00000000 len 1305296 - virtual 0x40d3f008
Loading TE_DMLT, Build 104-785, Protocol 6.03 104-859 [F#00FF]
2: DSP code base 0x809d4c60, max size 0x0021b3a0 (80dd4c60,80)
Download addr 0x00000000 len 1305296 - virtual 0x4093f008
Loading TE_DMLT, Build 104-785, Protocol 6.03 104-859 [F#00FF]
1: DSP code base 0x805d4c60, max size 0x0021b3a0 (80dd4c60,80)
Download addr 0x00000000 len 1305296 - virtual 0x4053f008
Loading TE_DMLT, Build 104-785, Protocol 6.03 104-859 [F#00FF]
0: DSP code base 0x801d4c60, max size 0x0021b3a0 (80dd4c60,80)
Download addr 0x00000000 len 1305296 - virtual 0x4013f008
Loading DSPDVF34 Download Combi-File Version 1.00 Build 103-492
Loading DIVA Server BRI 2M Kernel Version 1.00 Build 103-492
Loading HSCX Task Version 1.00 Build 103-492
Loading HSCXBR Task Version 1.00 Build 103-492
Loading PIAFSD Task Version 1.00 Build 103-492
Loading V.110 Kernel Task Version 1.00 Build 103-492
Loading V.110 Overlay (600) Version 1.00 Build 103-492
Loading V.110 Overlay (1200) Version 1.00 Build 103-492
Loading V.110 Overlay (1200/75) Version 1.00 Build 103-492
Loading V.110 Overlay (75/1200) Version 1.00 Build 103-492
Loading V.110 Overlay (2400) Version 1.00 Build 103-492
Loading V.110 Overlay (4800,9600,19200,38400) Version 1.00 Build 103-492
Loading V.110 Overlay (7200,14400,28800) Version 1.00 Build 103-492
Loading V.110 Overlay (12000,24000) Version 1.00 Build 103-492
Loading V.110 Overlay (48000) Version 1.00 Build 103-492
Loading V.110 Overlay (56000) Version 1.00 Build 103-492
Loading VOICEBR Task Version 1.00 Build 103-492
Loading DTMF Task Version 1.00 Build 103-492
Loading DTMFBR Task Version 1.00 Build 103-492
Loading SIG Task Version 1.00 Build 103-492
Loading TONEBR Task Version 1.00 Build 103-492
Loading Conferencing Overlay Version 1.00 Build 103-492
Loading TIKRNL81.F34 Task Version 1.00 Build 103-492
Loading SIG Overlay Version 1.00 Build 103-492
Loading FSK Overlay Version 1.00 Build 103-492
Loading V8.F34 Overlay Version 1.00 Build 103-492
Loading INFO Overlay Version 1.00 Build 103-492
Loading V.34 Overlay Version 1.00 Build 103-492
Loading INFOH Overlay Version 1.00 Build 103-492
Loading HV.34 Overlay Version 1.00 Build 103-492
Loading DIAL/FSK/FAX.F34 Overlay Version 1.00 Build 103-492
Loading DIAL.F34 Partial Overlay Version 1.00 Build 103-492
Loading FSKFAX.F34 Partial Overlay Version 1.00 Build 103-492
Loading FAX.F34 Partial Overlay Version 1.00 Build 103-492
Loading V.22/V.32 Overlay Version 1.00 Build 103-492
Loading V.32 Partial Overlay Version 1.00 Build 103-492
Loading V.90 DPCM Overlay Version 1.00 Build 103-492
Loading V.90 APCM Overlay Version 1.00 Build 103-492
Loading V.22FC Overlay Version 1.00 Build 103-492
Loading V.18 OWN-LK Overlay Version 1.00 Build 103-492
Loading V.OWN Overlay Version 1.00 Build 103-492
Loading VKRNLBR Task Version 1.00 Build 103-492
Loading G.711 Overlay Version 1.00 Build 103-492
Loading RTP G.711/G.726 Overlay Version 1.00 Build 103-492
Loading RTP GSM Overlay Version 1.00 Build 103-492
  Protocol = p0 (id 1 prot 1)
  TEI = automatic
  NT2 = 0
  DidLen = 0
  StableL2 = 2
  OAD1  = ""
  OSA1  = ""
  SPID1 = ""
  OAD2  = ""
  OSA2  = ""
  SPID2 = ""
  DSPInfo = 0x80(0x200000)
  Part68LevelLimiter = 1
  CardAddress = 0xde000000
  FPGAFeatures = 0x00000001
  XDIFeatures = 0x00000001
  Serial No = 19579
  Protocol = p1 (id 1 prot 1)
  TEI = automatic
  NT2 = 0
  DidLen = 0
  StableL2 = 2
  OAD1  = ""
  OSA1  = ""
  SPID1 = ""
  OAD2  = ""
  OSA2  = ""
  SPID2 = ""
  DSPInfo = 0x80(0x200000)
  Part68LevelLimiter = 1
  CardAddress = 0xde000000
  FPGAFeatures = 0x00000001
  XDIFeatures = 0x00000001
  Serial No = 19579
  Port No = 1
  Protocol = p2 (id 1 prot 1)
  TEI = automatic
  NT2 = 0
  DidLen = 0
  StableL2 = 2
  OAD1  = ""
  OSA1  = ""
  SPID1 = ""
  OAD2  = ""
  OSA2  = ""
  SPID2 = ""
  DSPInfo = 0x80(0x200000)
  Part68LevelLimiter = 1
  CardAddress = 0xde000000
  FPGAFeatures = 0x00000001
  XDIFeatures = 0x00000001
  Serial No = 19579
  Port No = 2
  Protocol = p3 (id 1 prot 1)
  TEI = automatic
  NT2 = 0
  DidLen = 0
  StableL2 = 2
  OAD1  = ""
  OSA1  = ""
  SPID1 = ""
  OAD2  = ""
  OSA2  = ""
  SPID2 = ""
  DSPInfo = 0x80(0x200000)
  Part68LevelLimiter = 1
  CardAddress = 0xde000000
  FPGAFeatures = 0x00000001
  XDIFeatures = 0x00000001
  Serial No = 19579
  Port No = 3
Raw protocol features: 000000ff
 OK


from syslog:
ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/none/none/1.1.4.1
dss1_divert module successfully installed
isdnloop-ISDN-driver Rev 1.1.4.1
Eicon DIVA - DIDD table (http://www.melware.net)
divadidd: Rel:2.0  Rev:1.15  Build:102-51(local_101)
Eicon DIVA Server driver (http://www.melware.net)
divas: Rel:2.0  Rev:1.58  Build: 102-52(local_101)
divas: support for: BRI/PCI adapters
divas: Diva Server 4BRI-8M 2.0 PCI bus: 00000002 fn: 00000048 insertion.
divas: thread started with pid 9
divas: thread started with pid 10
divas: thread started with pid 11
divas: thread started with pid 12
divas: Diva Server 4BRI-8M 2.0 PCI IRQ:10 SerNo:19579
divas: started with major 254
Eicon DIVA - User IDI (http://www.melware.net)
diva_idi: Rel:2.0  Rev:1.27  Build: local_101
diva_idi: started with major 253
Eicon Diva - native I4L Interface driver (http://www.melware.net)
diva2i4l: Rel:2.0  Rev:1.19/1.12

Jul  8 12:01:07 test kernel: diva2i4l: registered card 'diva0' with 2
channels
Jul  8 12:01:07 test kernel: diva2i4l: registered card 'diva1' with 2
channels
Jul  8 12:01:07 test kernel: diva2i4l: registered card 'diva2' with 2
channels
Jul  8 12:01:07 test kernel: diva2i4l: registered card 'diva3' with 2
channels


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*