[hylafax-users] Send but no recieve

To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Send but no recieve
From: alban Coujard <acoujard@xxxxxxxxxxx>
Date: Wed, 1 Jun 2005 11:57:35 +0200
Hello

I used a USR Sportster Voice 33.6 Fax Modem, I can send Fax but Can't 
receive... On a mandrake 10.1, the modem is on the serial port 2 (ttyS1), 
hylafax 4.2, 

I dont forget to do #faxgetty ttyS1

My config.ttyS1 file is :

CountryCode:		33
AreaCode:		3
FAXNumber:		+33.03.xxxxxxxx
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		quiet
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"NothingSetup"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	xonxoff		# software flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
ModemResultCodesCmd:	ATQ0X4		# enable result codes
#
ModemMfrQueryCmd:	!USR
ModemModelQueryCmd:	ATI3
ModemRevQueryCmd:	ATI7		# XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no flow control
Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for hardware flow control
Class1SFLOCmd:		""		# modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:	AT+FRS=1	# wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:	AT+FCLASS=0	# leave modem idling in class 0
ModemAnswerCmd:		AT+FCLASS=1A	# answer in Class 1
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0

probemodem command result is :

This looks like a Class 1 and 2.0 modem.

ATI0    RESULT = "OK"   RESPONSE = "3361"
ATI1    RESULT = "OK"   RESPONSE = "966D"
ATI2    RESULT = "OK"   RESPONSE = "OK"
ATI3    RESULT = "OK"   RESPONSE = "USRobotics Sportster Voice 33600 Fax Rev. 
2.0"
ATI4    RESULT = "OK"   RESPONSE = "USRobotics Sportster Voice 33600 Fax 
Settings..."
ATI5    RESULT = "Strike a key when ready . . ."        RESPONSE = "USRobotics 
Sportster Voice 33600 Fax NVRAM Settings..."
ATI6    RESULT = "OK"   RESPONSE = "USRobotics Sportster Voice 33600 Fax Link 
Diagnostics..."
ATI7    RESULT = "OK"   RESPONSE = "Configuration Profile..."
ATI8    RESULT = "OK"   RESPONSE = "Blacklist"
ATI9    RESULT = "OK"   RESPONSE = "(1.0USR0007\Modem\Sportster 33600 
FAX/VOICE EXT)FF"

Class 1 stuff...

AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,2.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "0"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
AT+FJUNK=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJUNK?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAE=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAE? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FTH=?        RESULT = "OK"   RESPONSE = 
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRH=?        RESULT = "OK"   RESPONSE = 
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTM=?        RESULT = "OK"   RESPONSE = 
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FRM=?        RESULT = "OK"   RESPONSE = 
"3,24,48,72,73,74,96,97,98,121,122,145,146"
AT+FTS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
Class 2.0 stuff...

AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,2.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=2.0   RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
AT+FJU=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJU? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FDR=?        RESULT = ""     RESPONSE = ""
AT+FDT=?        RESULT = ""     RESPONSE = ""
AT+FIP=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAP=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAP? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FBS? RESULT = "OK"   RESPONSE = "1800,4000"
AT+FBO=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FBO? RESULT = "OK"   RESPONSE = "0"
AT+FBU=?        RESULT = "OK"   RESPONSE = "0"
AT+FBU? RESULT = "OK"   RESPONSE = "0"
AT+FCC=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),0,0,0,
(0-7)"
AT+FCC? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,5"
AT+FCQ=?        RESULT = "OK"   RESPONSE = "(0-2),(0-2)"
AT+FCQ? RESULT = "OK"   RESPONSE = "1,0"
AT+FCR=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FCR? RESULT = "OK"   RESPONSE = "1"
AT+FCS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FCS? RESULT = "OK"   RESPONSE = "0,0,0,0,0,0,0,0"
AT+FCT=?        RESULT = "OK"   RESPONSE = "(0-255)"
AT+FCT? RESULT = "OK"   RESPONSE = "0"
AT+FEA=?        RESULT = "OK"   RESPONSE = "0"
AT+FEA? RESULT = "OK"   RESPONSE = "0"
AT+FFC=?        RESULT = "OK"   RESPONSE = "0,0,0,0"
AT+FFC? RESULT = "OK"   RESPONSE = "0,0,0,0"
AT+FFD=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FFD? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FHS? RESULT = "OK"   RESPONSE = "0"
AT+FIE=?        RESULT = "OK"   RESPONSE = "0"
AT+FIE? RESULT = "OK"   RESPONSE = "0"
AT+FIS=?        RESULT = "OK"   RESPONSE = "(0,1),(0-5),(0-2),(0-2),0,0,0,
(0-7)"
AT+FIS? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,5"
AT+FIT=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FIT? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FLI=?        RESULT = "OK"   RESPONSE = "(20-7E)"
AT+FLI? RESULT = "OK"   RESPONSE = """"
AT+FLO=?        RESULT = "OK"   RESPONSE = "(0-2)"
AT+FLO? RESULT = "OK"   RESPONSE = "1"
AT+FLP=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FLP? RESULT = "OK"   RESPONSE = "0"
AT+FMI? RESULT = "OK"   RESPONSE = "USRobotics Sportster V.34+ FAX"
AT+FMM? RESULT = "OK"   RESPONSE = "OK"
AT+FMR? RESULT = "OK"   RESPONSE = "OK"
AT+FMS=?        RESULT = "OK"   RESPONSE = "(0-5)"
AT+FMS? RESULT = "OK"   RESPONSE = "0"
AT+FNR=?        RESULT = "OK"   RESPONSE = "(0,1),(0,1),(0,1),(0,1)"
AT+FNR? RESULT = "OK"   RESPONSE = "0,0,0,0"
AT+FNS=?        RESULT = "OK"   RESPONSE = "(20-7E)"
AT+FNS? RESULT = "OK"   RESPONSE = """"
AT+FPA=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPA? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPI=?        RESULT = "OK"   RESPONSE = "(20-7E)"
AT+FPI? RESULT = "OK"   RESPONSE = """"
AT+FPP=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FPP? RESULT = "OK"   RESPONSE = "0"
AT+FPR=?        RESULT = "OK"   RESPONSE = "(0,1,2,4,8,16,24)"
AT+FPR? RESULT = "OK"   RESPONSE = "0"
AT+FPS=?        RESULT = "OK"   RESPONSE = "(1-5)"
AT+FPS? RESULT = "OK"   RESPONSE = "1"
AT+FPW=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FPW? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRQ=?        RESULT = "OK"   RESPONSE = "(0-2),(0-2)"
AT+FRQ? RESULT = "OK"   RESPONSE = "0,N"
AT+FRY=?        RESULT = "OK"   RESPONSE = "0"
AT+FRY? RESULT = "OK"   RESPONSE = "0"
AT+FSA=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FSA? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FSP=?        RESULT = "OK"   RESPONSE = "(0,1)"
AT+FSP? RESULT = "OK"   RESPONSE = "0"
AT+IFC=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+IFC? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+IPR=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+IPR? RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FKS=?        RESULT = "ERROR"        RESPONSE = "ERROR"

/var/log/messages:

Jun  1 11:50:33 amonbofis FaxGetty[8024]: MODEM USR USRobotics Sportster Voice 
33600 Fax Rev. 2.0/Configuration Profile... Product type           France 
External Options                V32bis,V.FC,V.34+ Fax Options            
Class 1/Class 2.0 Clock Freq             92.0Mhz Eprom                  256k 
Ram                    64k EPROM date             5/10/96 DSP date               
5/10/96 EPROM rev              2.0 DSP rev                2.0
Jun  1 11:50:33 amonbofis FaxGetty[8024]: LOCKWAIT
Jun  1 11:50:46 amonbofis FaxSend[8678]: MODEM USR USRobotics Sportster Voice 
33600 Fax Rev. 2.0/Configuration Profile... Product type           France 
External Options                V32bis,V.FC,V.34+ Fax Options            
Class 1/Class 2.0 Clock Freq             92.0Mhz Eprom                  256k 
Ram                    64k EPROM date             5/10/96 DSP date               
5/10/96 EPROM rev              2.0 DSP rev                2.0


What I do wrong ? thank for futur all

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
Follow-Ups:
- Re: [hylafax-users] Send but no recieve
  - From: Pedro
Prev by Date: [hylafax-users] Preliminary question.
Next by Date: Re: [hylafax-users] Send but no recieve
Previous by thread: [hylafax-users] Send but no recieve
Next by thread: Re: [hylafax-users] Send but no recieve
Index(es):
- Main
- Thread
Project hosted by iFAX Solutions