 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Send but no recieve
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Send but no recieve
- From: alban Coujard <acoujard@xxxxxxxxxxx>
- Date: Wed, 1 Jun 2005 12:01:10 +0200
To: hylafax-users@xxxxxxxxxxx Hello I used a USR Sportster Voice 33.6 Fax Modem, I can send Fax but Can't receive... On a mandrake 10.1, the modem is on the serial port 2 (ttyS1), hylafax 4.2, I dont forget to do #faxgetty ttyS1 My config.ttyS1 file is : CountryCode: 33 AreaCode: 3 FAXNumber: +33.03.xxxxxxxx LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: quiet GettyArgs: "-h %l dx_%s" LocalIdentifier: "NothingSetup" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use class 1 interface ModemRate: 19200 # rate for DCE-DTE communication ModemFlowControl: xonxoff # software flow control # ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control ModemResultCodesCmd: ATQ0X4 # enable result codes # ModemMfrQueryCmd: !USR ModemModelQueryCmd: ATI3 ModemRevQueryCmd: ATI7 # XXX returns a multi-line result # # When AT+FCLASS=1 is issued the modem automatically switches # to software flow control; these parameters let the fax software # reset flow control as needed after entering Class 1. # Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow control Class1SFLOCmd: "" # modem does this automatically # # This should resolve "DIS/DTC received 3 times" errors: # Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for response # # The remainder of this configuration is included so that the # modem "idles" in Class 0 while not sending or receiving facsimile. # ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0 ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1 # # Disables the reporting of bad frames by the modem. This # overcomes a firmware problem in the x2 and V90 Sportsters. # It is not necessary for the Courier modem. # Class2NRCmd: AT+FNR=1,1,1,0 probemodem command result is : This looks like a Class 1 and 2.0 modem. ATI0 RESULT = "OK" RESPONSE = "3361" ATI1 RESULT = "OK" RESPONSE = "966D" ATI2 RESULT = "OK" RESPONSE = "OK" ATI3 RESULT = "OK" RESPONSE = "USRobotics Sportster Voice 33600 Fax Rev. 2.0" ATI4 RESULT = "OK" RESPONSE = "USRobotics Sportster Voice 33600 Fax Settings..." ATI5 RESULT = "Strike a key when ready . . ." RESPONSE = "USRobotics Sportster Voice 33600 Fax NVRAM Settings..." ATI6 RESULT = "OK" RESPONSE = "USRobotics Sportster Voice 33600 Fax Link Diagnostics..." ATI7 RESULT = "OK" RESPONSE = "Configuration Profile..." ATI8 RESULT = "OK" RESPONSE = "Blacklist" ATI9 RESULT = "OK" RESPONSE = "(1.0USR0007\Modem\Sportster 33600 FAX/VOICE EXT)FF" Class 1 stuff... AT+FCLASS=? RESULT = "OK" RESPONSE = "0,1,2.0" AT+FCLASS? RESULT = "OK" RESPONSE = "0" AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK" AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK" AT+FCLASS? RESULT = "OK" RESPONSE = "1" AT+FJUNK=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FJUNK? RESULT = "ERROR" RESPONSE = "ERROR" AT+FAA=? RESULT = "OK" RESPONSE = "(0,1)" AT+FAA? RESULT = "OK" RESPONSE = "0" AT+FAE=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FAE? RESULT = "ERROR" RESPONSE = "ERROR" AT+FTH=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146" AT+FRH=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146" AT+FTM=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146" AT+FRM=? RESULT = "OK" RESPONSE = "3,24,48,72,73,74,96,97,98,121,122,145,146" AT+FTS=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FRS=? RESULT = "ERROR" RESPONSE = "ERROR" Class 2.0 stuff... AT+FCLASS=? RESULT = "OK" RESPONSE = "0,1,2.0" AT+FCLASS? RESULT = "OK" RESPONSE = "1" AT+FCLASS=0 RESULT = "OK" RESPONSE = "OK" AT+FCLASS=1 RESULT = "OK" RESPONSE = "OK" AT+FCLASS=2.0 RESULT = "OK" RESPONSE = "OK" AT+FCLASS? RESULT = "OK" RESPONSE = "1" AT+FJU=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FJU? RESULT = "ERROR" RESPONSE = "ERROR" AT+FDR=? RESULT = "" RESPONSE = "" AT+FDT=? RESULT = "" RESPONSE = "" AT+FIP=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FAA=? RESULT = "OK" RESPONSE = "(0,1)" AT+FAA? RESULT = "OK" RESPONSE = "0" AT+FAP=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FAP? RESULT = "ERROR" RESPONSE = "ERROR" AT+FBS? RESULT = "OK" RESPONSE = "1800,4000" AT+FBO=? RESULT = "OK" RESPONSE = "(0,1)" AT+FBO? RESULT = "OK" RESPONSE = "0" AT+FBU=? RESULT = "OK" RESPONSE = "0" AT+FBU? RESULT = "OK" RESPONSE = "0" AT+FCC=? RESULT = "OK" RESPONSE = "(0,1),(0-5),(0-2),(0-2),0,0,0, (0-7)" AT+FCC? RESULT = "OK" RESPONSE = "1,5,0,2,0,0,0,5" AT+FCQ=? RESULT = "OK" RESPONSE = "(0-2),(0-2)" AT+FCQ? RESULT = "OK" RESPONSE = "1,0" AT+FCR=? RESULT = "OK" RESPONSE = "(0,1)" AT+FCR? RESULT = "OK" RESPONSE = "1" AT+FCS=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FCS? RESULT = "OK" RESPONSE = "0,0,0,0,0,0,0,0" AT+FCT=? RESULT = "OK" RESPONSE = "(0-255)" AT+FCT? RESULT = "OK" RESPONSE = "0" AT+FEA=? RESULT = "OK" RESPONSE = "0" AT+FEA? RESULT = "OK" RESPONSE = "0" AT+FFC=? RESULT = "OK" RESPONSE = "0,0,0,0" AT+FFC? RESULT = "OK" RESPONSE = "0,0,0,0" AT+FFD=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FFD? RESULT = "ERROR" RESPONSE = "ERROR" AT+FHS? RESULT = "OK" RESPONSE = "0" AT+FIE=? RESULT = "OK" RESPONSE = "0" AT+FIE? RESULT = "OK" RESPONSE = "0" AT+FIS=? RESULT = "OK" RESPONSE = "(0,1),(0-5),(0-2),(0-2),0,0,0, (0-7)" AT+FIS? RESULT = "OK" RESPONSE = "1,5,0,2,0,0,0,5" AT+FIT=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FIT? RESULT = "ERROR" RESPONSE = "ERROR" AT+FLI=? RESULT = "OK" RESPONSE = "(20-7E)" AT+FLI? RESULT = "OK" RESPONSE = """" AT+FLO=? RESULT = "OK" RESPONSE = "(0-2)" AT+FLO? RESULT = "OK" RESPONSE = "1" AT+FLP=? RESULT = "OK" RESPONSE = "(0,1)" AT+FLP? RESULT = "OK" RESPONSE = "0" AT+FMI? RESULT = "OK" RESPONSE = "USRobotics Sportster V.34+ FAX" AT+FMM? RESULT = "OK" RESPONSE = "OK" AT+FMR? RESULT = "OK" RESPONSE = "OK" AT+FMS=? RESULT = "OK" RESPONSE = "(0-5)" AT+FMS? RESULT = "OK" RESPONSE = "0" AT+FNR=? RESULT = "OK" RESPONSE = "(0,1),(0,1),(0,1),(0,1)" AT+FNR? RESULT = "OK" RESPONSE = "0,0,0,0" AT+FNS=? RESULT = "OK" RESPONSE = "(20-7E)" AT+FNS? RESULT = "OK" RESPONSE = """" AT+FPA=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FPA? RESULT = "ERROR" RESPONSE = "ERROR" AT+FPI=? RESULT = "OK" RESPONSE = "(20-7E)" AT+FPI? RESULT = "OK" RESPONSE = """" AT+FPP=? RESULT = "OK" RESPONSE = "(0,1)" AT+FPP? RESULT = "OK" RESPONSE = "0" AT+FPR=? RESULT = "OK" RESPONSE = "(0,1,2,4,8,16,24)" AT+FPR? RESULT = "OK" RESPONSE = "0" AT+FPS=? RESULT = "OK" RESPONSE = "(1-5)" AT+FPS? RESULT = "OK" RESPONSE = "1" AT+FPW=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FPW? RESULT = "ERROR" RESPONSE = "ERROR" AT+FRQ=? RESULT = "OK" RESPONSE = "(0-2),(0-2)" AT+FRQ? RESULT = "OK" RESPONSE = "0,N" AT+FRY=? RESULT = "OK" RESPONSE = "0" AT+FRY? RESULT = "OK" RESPONSE = "0" AT+FSA=? RESULT = "ERROR" RESPONSE = "ERROR" AT+FSA? RESULT = "ERROR" RESPONSE = "ERROR" AT+FSP=? RESULT = "OK" RESPONSE = "(0,1)" AT+FSP? RESULT = "OK" RESPONSE = "0" AT+IFC=? RESULT = "ERROR" RESPONSE = "ERROR" AT+IFC? RESULT = "ERROR" RESPONSE = "ERROR" AT+IPR=? RESULT = "ERROR" RESPONSE = "ERROR" AT+IPR? RESULT = "ERROR" RESPONSE = "ERROR" AT+FKS=? RESULT = "ERROR" RESPONSE = "ERROR" /var/log/messages: Jun 1 11:50:33 amonbofis FaxGetty[8024]: MODEM USR USRobotics Sportster Voice 33600 Fax Rev. 2.0/Configuration Profile... Product type France External Options V32bis,V.FC,V.34+ Fax Options Class 1/Class 2.0 Clock Freq 92.0Mhz Eprom 256k Ram 64k EPROM date 5/10/96 DSP date 5/10/96 EPROM rev 2.0 DSP rev 2.0 Jun 1 11:50:33 amonbofis FaxGetty[8024]: LOCKWAIT Jun 1 11:50:46 amonbofis FaxSend[8678]: MODEM USR USRobotics Sportster Voice 33600 Fax Rev. 2.0/Configuration Profile... Product type France External Options V32bis,V.FC,V.34+ Fax Options Class 1/Class 2.0 Clock Freq 92.0Mhz Eprom 256k Ram 64k EPROM date 5/10/96 DSP date 5/10/96 EPROM rev 2.0 DSP rev 2.0 What I do wrong ? thank for futur all ------------------------------------------------------- Alban coujard ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Next by Date: [hylafax-users] Preliminary question.
- Next by thread: [hylafax-users] Send but no recieve
- Index(es):
Project hosted by iFAX Solutions