Re: [hylafax-users] Send but no recieve

[Pedro <procadas@xxxxxxxxx>]

Did you rerun init? Ie, init q?

--- alban Coujard <acoujard@xxxxxxxxxxx> wrote:

> Hello
> 
> I used a USR Sportster Voice 33.6 Fax Modem, I can
> send Fax but Can't 
> receive... On a mandrake 10.1, the modem is on the
> serial port 2 (ttyS1), 
> hylafax 4.2, 
> 
> I dont forget to do #faxgetty ttyS1
> 
> My config.ttyS1 file is :
> 
> CountryCode:		33
> AreaCode:		3
> FAXNumber:		+33.03.xxxxxxxx
> LongDistancePrefix:	0
> InternationalPrefix:	00
> DialStringRules:	etc/dialrules
> ServerTracing:		1
> SessionTracing:		11
> RecvFileMode:		0600
> LogFileMode:		0600
> DeviceMode:		0600
> RingsBeforeAnswer:	1
> SpeakerVolume:		quiet
> GettyArgs:		"-h %l dx_%s"
> LocalIdentifier:	"NothingSetup"
> TagLineFont:		etc/lutRS18.pcf
> TagLineFormat:		"From %%l|%c|Page %%P of %%T"
> MaxRecvPages:		25
> #
> #
> # Modem-related stuff: should reflect modem command
> interface
> # and hardware connection/cabling (e.g. flow
> control).
> #
> ModemType:		Class1		# use class 1 interface
> ModemRate:		19200		# rate for DCE-DTE communication
> ModemFlowControl:	xonxoff		# software flow control
> #
> ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop
> resets modem
> ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects
> carrier (or not)
> ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no
> flow control
> ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for
> hardware flow control
> ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for
> software flow control
> ModemResultCodesCmd:	ATQ0X4		# enable result codes
> #
> ModemMfrQueryCmd:	!USR
> ModemModelQueryCmd:	ATI3
> ModemRevQueryCmd:	ATI7		# XXX returns a multi-line
> result
> #
> # When AT+FCLASS=1 is issued the modem automatically
> switches
> # to software flow control; these parameters let the
> fax software
> # reset flow control as needed after entering Class
> 1.
> #
> Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no
> flow control
> Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for
> hardware flow control
> Class1SFLOCmd:		""		# modem does this automatically
> #
> # This should resolve "DIS/DTC received 3 times"
> errors:
> #
> Class1ResponseWaitCmd:	AT+FRS=1	# wait after sending
> TCF for response
> #
> # The remainder of this configuration is included so
> that the
> # modem "idles" in Class 0 while not sending or
> receiving facsimile.
> #
> ModemSetupAACmd:	AT+FCLASS=0	# leave modem idling in
> class 0
> ModemAnswerCmd:		AT+FCLASS=1A	# answer in Class 1
> #
> # Disables the reporting of bad frames by the modem.
>  This
> # overcomes a firmware problem in the x2 and V90
> Sportsters.
> # It is not necessary for the Courier modem.
> #
> Class2NRCmd:    AT+FNR=1,1,1,0
> 
> probemodem command result is :
> 
> This looks like a Class 1 and 2.0 modem.
> 
> ATI0    RESULT = "OK"   RESPONSE = "3361"
> ATI1    RESULT = "OK"   RESPONSE = "966D"
> ATI2    RESULT = "OK"   RESPONSE = "OK"
> ATI3    RESULT = "OK"   RESPONSE = "USRobotics
> Sportster Voice 33600 Fax Rev. 
> 2.0"
> ATI4    RESULT = "OK"   RESPONSE = "USRobotics
> Sportster Voice 33600 Fax 
> Settings..."
> ATI5    RESULT = "Strike a key when ready . . ."    
>    RESPONSE = "USRobotics 
> Sportster Voice 33600 Fax NVRAM Settings..."
> ATI6    RESULT = "OK"   RESPONSE = "USRobotics
> Sportster Voice 33600 Fax Link 
> Diagnostics..."
> ATI7    RESULT = "OK"   RESPONSE = "Configuration
> Profile..."
> ATI8    RESULT = "OK"   RESPONSE = "Blacklist"
> ATI9    RESULT = "OK"   RESPONSE =
> "(1.0USR0007\Modem\Sportster 33600 
> FAX/VOICE EXT)FF"
> 
> Class 1 stuff...
> 
> AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,2.0"
> AT+FCLASS?      RESULT = "OK"   RESPONSE = "0"
> AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
> AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
> AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
> AT+FJUNK=?      RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FJUNK?       RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
> AT+FAA? RESULT = "OK"   RESPONSE = "0"
> AT+FAE=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FAE? RESULT = "ERROR"        RESPONSE = "ERROR"
> AT+FTH=?        RESULT = "OK"   RESPONSE = 
> "3,24,48,72,73,74,96,97,98,121,122,145,146"
> AT+FRH=?        RESULT = "OK"   RESPONSE = 
> "3,24,48,72,73,74,96,97,98,121,122,145,146"
> AT+FTM=?        RESULT = "OK"   RESPONSE = 
> "3,24,48,72,73,74,96,97,98,121,122,145,146"
> AT+FRM=?        RESULT = "OK"   RESPONSE = 
> "3,24,48,72,73,74,96,97,98,121,122,145,146"
> AT+FTS=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FRS=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> Class 2.0 stuff...
> 
> AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,2.0"
> AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
> AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
> AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
> AT+FCLASS=2.0   RESULT = "OK"   RESPONSE = "OK"
> AT+FCLASS?      RESULT = "OK"   RESPONSE = "1"
> AT+FJU=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FJU? RESULT = "ERROR"        RESPONSE = "ERROR"
> AT+FDR=?        RESULT = ""     RESPONSE = ""
> AT+FDT=?        RESULT = ""     RESPONSE = ""
> AT+FIP=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FAA=?        RESULT = "OK"   RESPONSE = "(0,1)"
> AT+FAA? RESULT = "OK"   RESPONSE = "0"
> AT+FAP=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FAP? RESULT = "ERROR"        RESPONSE = "ERROR"
> AT+FBS? RESULT = "OK"   RESPONSE = "1800,4000"
> AT+FBO=?        RESULT = "OK"   RESPONSE = "(0,1)"
> AT+FBO? RESULT = "OK"   RESPONSE = "0"
> AT+FBU=?        RESULT = "OK"   RESPONSE = "0"
> AT+FBU? RESULT = "OK"   RESPONSE = "0"
> AT+FCC=?        RESULT = "OK"   RESPONSE =
> "(0,1),(0-5),(0-2),(0-2),0,0,0,
> (0-7)"
> AT+FCC? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,5"
> AT+FCQ=?        RESULT = "OK"   RESPONSE =
> "(0-2),(0-2)"
> AT+FCQ? RESULT = "OK"   RESPONSE = "1,0"
> AT+FCR=?        RESULT = "OK"   RESPONSE = "(0,1)"
> AT+FCR? RESULT = "OK"   RESPONSE = "1"
> AT+FCS=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FCS? RESULT = "OK"   RESPONSE = "0,0,0,0,0,0,0,0"
> AT+FCT=?        RESULT = "OK"   RESPONSE = "(0-255)"
> AT+FCT? RESULT = "OK"   RESPONSE = "0"
> AT+FEA=?        RESULT = "OK"   RESPONSE = "0"
> AT+FEA? RESULT = "OK"   RESPONSE = "0"
> AT+FFC=?        RESULT = "OK"   RESPONSE = "0,0,0,0"
> AT+FFC? RESULT = "OK"   RESPONSE = "0,0,0,0"
> AT+FFD=?        RESULT = "ERROR"        RESPONSE =
> "ERROR"
> AT+FFD? RESULT = "ERROR"        RESPONSE = "ERROR"
> AT+FHS? RESULT = "OK"   RESPONSE = "0"
> AT+FIE=?        RESULT = "OK"   RESPONSE = "0"
> AT+FIE? RESULT = "OK"   RESPONSE = "0"
> AT+FIS=?        RESULT = "OK"   RESPONSE =
> "(0,1),(0-5),(0-2),(0-2),0,0,0,
> (0-7)"
> AT+FIS? RESULT = "OK"   RESPONSE = "1,5,0,2,0,0,0,5"
> 
=== message truncated ===



		
__________________________________ 
Discover Yahoo! 
Find restaurants, movies, travel and more fun for the weekend. Check it out! 
http://discover.yahoo.com/weekend.php 


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*