[hylafax-users] Force using 2D-MR

[Matthias Reich <rei@xxxxxxxx>]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hello List,

still using hylafax 4.1.7 with multitech MT1432BG.

I need to force hylafax to use 2D-MR to a destination.
I already set Use2D in the config-file to Yes, but the transmission is still 
in 1D-MR.

I started sendfax with: sendfax -2 -d 12345 FILE
but no success (hylfax still sends with 1D-MR.
The modem (Multitech) supports 2D-MR.
When I use a different server, the fax to that destination is sent with 2D-MR.
I deleted the info-file but still no success. hylafax sends the fax with 1D-MR 
encoding.

here is the extract from the logs:
[...]
Apr 12 12:27:46.32: [29785]: REMOTE NSF "86 00 CA 00 00 E4 01 C8 40 F0 03 18 
80 
00 00"
Apr 12 12:27:46.32: [29785]: NSF remote fax equipment: unknown
Apr 12 12:27:46.32: [29785]: --> [28:+FCSI:"    +49 5422 9441 14"]
Apr 12 12:27:46.32: [29785]: REMOTE CSI "+49 5422 9441 14"
Apr 12 12:27:46.32: [29785]: --> [21:+FDIS:1,5,0,2,1,2,1,3]
Apr 12 12:27:46.43: [29785]: --> [2:OK]
Apr 12 12:27:46.43: [29785]: REMOTE best rate 14400 bit/s
Apr 12 12:27:46.43: [29785]: REMOTE max page width 1728 pixels in 215 mm
Apr 12 12:27:46.43: [29785]: REMOTE max unlimited page length
Apr 12 12:27:46.43: [29785]: REMOTE best vres 7.7 line/mm
Apr 12 12:27:46.43: [29785]: REMOTE best format 2-D MR
Apr 12 12:27:46.43: [29785]: REMOTE supports T.30 Annex C, half duplex ECM
Apr 12 12:27:46.43: [29785]: REMOTE best 10 ms/scanline
Apr 12 12:27:46.43: [29785]: USE 9600 bit/s
Apr 12 12:27:46.43: [29785]: USE 10 ms/scanline
Apr 12 12:27:46.43: [29785]: SEND file "docq/doc10589.ps;00"
Apr 12 12:27:46.43: [29785]: USE page width 1728 pixels in 215 mm
Apr 12 12:27:46.43: [29785]: USE unlimited page length
Apr 12 12:27:46.43: [29785]: USE 3.85 line/mm
Apr 12 12:27:46.43: [29785]: USE 1-D MR
Apr 12 12:27:46.43: [29785]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,3\r]
Apr 12 12:27:46.75: [29785]: --> [2:OK]
[...]

When sending with 1D-MR the session ends with:
[...]
Apr 12 13:38:48.09: [25807]: SEND send EOP (no more pages or documents)
Apr 12 13:38:48.09: [25807]: <-- [9:AT+FET=2\r]
Apr 12 13:38:50.70: [25807]: --> [14:+FHT:FF 13 2F ]
Apr 12 13:38:52.20: [25807]: --> [14:+FHT:FF 13 2F ]
Apr 12 13:38:53.80: [25807]: --> [14:+FHT:FF 13 2F ]
Apr 12 13:38:55.30: [25807]: --> [14:+FHT:FF 13 FB ]
Apr 12 13:38:55.77: [25807]: --> [8:+FHNG:54]
Apr 12 13:38:55.77: [25807]: REMOTE HANGUP: No response to EOP repeated 3 
times (code 54)
Apr 12 13:38:55.77: [25807]: <-- [5:ATH0\r]
Apr 12 13:38:56.27: [25807]: --> [2:OK]
Apr 12 13:38:56.27: [25807]: MODEM set DTR OFF
Apr 12 13:38:56.27: [25807]: SESSION END


when I use another server with an equal modem and config-file the result is:

[...]
Apr 12 10:17:55.52: [17668]: REMOTE NSF "86 00 CA 00 00 E4 01 C8 40 F0 03 18 
80 
00 00"
Apr 12 10:17:55.52: [17668]: NSF remote fax equipment: unknown
Apr 12 10:17:55.52: [17668]: --> [28:+FCSI:"    +49 5422 9441 14"]
Apr 12 10:17:55.52: [17668]: REMOTE CSI "+49 5422 9441 14"
Apr 12 10:17:55.63: [17668]: --> [21:+FDIS:1,5,0,2,1,2,1,3]
Apr 12 10:17:55.63: [17668]: --> [2:OK]
Apr 12 10:17:55.63: [17668]: REMOTE best rate 14400 bit/s
Apr 12 10:17:55.63: [17668]: REMOTE max page width 1728 pixels in 215 mm
Apr 12 10:17:55.63: [17668]: REMOTE max unlimited page length
Apr 12 10:17:55.63: [17668]: REMOTE best vres 7.7 line/mm
Apr 12 10:17:55.63: [17668]: REMOTE best format 2-D MR
Apr 12 10:17:55.63: [17668]: REMOTE supports T.30 Annex C, half duplex ECM
Apr 12 10:17:55.63: [17668]: REMOTE best 10 ms/scanline
Apr 12 10:17:55.63: [17668]: USE 9600 bit/s
Apr 12 10:17:55.63: [17668]: USE 10 ms/scanline
Apr 12 10:17:55.63: [17668]: SEND file "docq/doc17202.ps;40"
Apr 12 10:17:55.63: [17668]: USE page width 1728 pixels in 215 mm
Apr 12 10:17:55.63: [17668]: USE unlimited page length
Apr 12 10:17:55.63: [17668]: USE 3.85 line/mm
Apr 12 10:17:55.63: [17668]: USE 2-D MR
Apr 12 10:17:55.63: [17668]: <-- [24:AT+FDIS=0,3,0,2,1,0,0,3\r]
Apr 12 10:17:55.95: [17668]: --> [2:OK]
[...]
Apr 12 10:18:25.54: [17668]: SEND send EOP (no more pages or documents)
Apr 12 10:18:25.54: [17668]: <-- [9:AT+FET=2\r]
Apr 12 10:18:28.97: [17668]: --> [14:+FHT:FF 13 2F ]
Apr 12 10:18:30.73: [17668]: --> [14:+FHR:FF 13 8C ]
Apr 12 10:18:30.73: [17668]: --> [7:+FPTS:1]
Apr 12 10:18:31.67: [17668]: --> [14:+FHT:FF 13 FB ]
Apr 12 10:18:32.15: [17668]: --> [7:+FHNG:0]
Apr 12 10:18:32.15: [17668]: REMOTE HANGUP: Normal and proper end of 
connection 
(code 0)
Apr 12 10:18:32.15: [17668]: SEND recv MCF (message confirmation)


The interesting part is the one after SEND send EOP
If failing the lines are:
Apr 12 13:38:48.09: [25807]: SEND send EOP (no more pages or documents)
Apr 12 13:38:48.09: [25807]: <-- [9:AT+FET=2\r]
Apr 12 13:38:50.70: [25807]: --> [14:+FHT:FF 13 2F ]
Apr 12 13:38:52.20: [25807]: --> [14:+FHT:FF 13 2F ]
Apr 12 13:38:53.80: [25807]: --> [14:+FHT:FF 13 2F ]
Apr 12 13:38:55.30: [25807]: --> [14:+FHT:FF 13 FB ]
Apr 12 13:38:55.77: [25807]: --> [8:+FHNG:54]

successful lines look like:

So how can I tell hylafax to use 2D-MR
Apr 12 10:18:25.54: [17668]: SEND send EOP (no more pages or documents)
Apr 12 10:18:25.54: [17668]: <-- [9:AT+FET=2\r]
Apr 12 10:18:28.97: [17668]: --> [14:+FHT:FF 13 2F ]
Apr 12 10:18:30.73: [17668]: --> [14:+FHR:FF 13 8C ]
Apr 12 10:18:30.73: [17668]: --> [7:+FPTS:1]
Apr 12 10:18:31.67: [17668]: --> [14:+FHT:FF 13 FB ]
Apr 12 10:18:32.15: [17668]: --> [7:+FHNG:0]
Apr 12 10:18:32.15: [17668]: REMOTE HANGUP: Normal and proper end of 
connection 

the only difference is that one file is send with 2D-MR the other one with 
1D-MR. I use the same hylafax-version with the same modem and the same 
firmware on the modems just on different servers

Any suggestions ?

TIA

- -m


- -- 
HAGOS eG                 phone: +49 711 7880592
Matthias Reich             fax: +49 711 7880535
Industriestr. 62           web: http://www.hagos.de
D-70565 Stuttgart         mail: rei@xxxxxxxx
Germany
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.0 (GNU/Linux)

iD8DBQFCW7VpcjMVLPQ5oUkRArWWAJ9u3QklduMu4zkSEUsd8JpPaYa2hgCfQxq3
y13RYhuMb0kRqsBVrYdBhRQ=
=yn42
-----END PGP SIGNATURE-----

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*