HylaFAX The world's most advanced open source fax server
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: [hylafax-users] MultiTech ISI card failure

Below is the results from configuring it with class 1 and class 1.0. I didn't restart hylafax inbetween these configurations but did restart the instances of faxgetty.

Peter

CLASS 1******************************************

[root@silver ~]# tail -f /etc/hylafax/log/c000000041
Feb 07 11:44:03.30: [22677]: SESSION BEGIN 000000041 17037038168824
Feb 07 11:44:03.30: [22677]: HylaFAX (tm) Version 4.2.0
Feb 07 11:44:03.30: [22677]: SEND FAX: JOB 42 DEST 7038168824 COMMID 000000041 DEVICE '/dev/ttyS49'
Feb 07 11:44:03.30: [22677]: <-- [12:AT+FCLASS=1\r]
Feb 07 11:44:03.41: [22677]: --> [2:OK]
Feb 07 11:44:03.42: [22677]: DIAL 7038168824
Feb 07 11:44:03.42: [22677]: <-- [15:ATDT7038168824\r]
Feb 07 11:44:22.84: [22677]: --> [7:CONNECT]
Feb 07 11:44:24.32: [22677]: --> [2:OK]
Feb 07 11:44:24.32: [22677]: REMOTE NSF "00 00 11 80 00 8A 48 00 FF 00 80 80 80 00"
Feb 07 11:44:24.32: [22677]: NSF remote fax equipment: Canon
Feb 07 11:44:24.32: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:44:24.34: [22677]: --> [7:CONNECT]
Feb 07 11:44:24.76: [22677]: --> [2:OK]
Feb 07 11:44:24.76: [22677]: REMOTE best rate 33600 bit/s
Feb 07 11:44:24.76: [22677]: REMOTE max A4 page width (215 mm)
Feb 07 11:44:24.76: [22677]: REMOTE max unlimited page length
Feb 07 11:44:24.76: [22677]: REMOTE best vres R16 x 15.4 line/mm
Feb 07 11:44:24.76: [22677]: REMOTE best format 2-D MMR
Feb 07 11:44:24.76: [22677]: REMOTE supports T.30 Annex A, 256-byte ECM
Feb 07 11:44:24.76: [22677]: REMOTE best 20 ms/scanline
Feb 07 11:44:24.76: [22677]: USE 14400 bit/s
Feb 07 11:44:24.76: [22677]: USE 20 ms/scanline
Feb 07 11:44:24.76: [22677]: SEND file "docq/doc42.ps;41"
Feb 07 11:44:24.76: [22677]: USE A4 page width (215 mm)
Feb 07 11:44:24.76: [22677]: USE unlimited page length
Feb 07 11:44:24.76: [22677]: USE 7.7 line/mm
Feb 07 11:44:24.76: [22677]: USE 2-D MR
Feb 07 11:44:24.76: [22677]: SEND training at v.17 14400 bit/s
Feb 07 11:44:24.76: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:44:25.73: [22677]: --> [7:CONNECT]
Feb 07 11:44:25.73: [22677]: <-- data [23]
Feb 07 11:44:25.73: [22677]: <-- data [2]
Feb 07 11:44:25.75: [22677]: --> [7:CONNECT]
Feb 07 11:44:25.75: [22677]: <-- data [6]
Feb 07 11:44:25.75: [22677]: <-- data [2]
Feb 07 11:44:26.90: [22677]: --> [2:OK]
Feb 07 11:44:26.90: [22677]: <-- [9:AT+FTS=7\r]
Feb 07 11:44:26.96: [22677]: --> [2:OK]
Feb 07 11:44:26.96: [22677]: <-- [11:AT+FTM=145\r]
Feb 07 11:44:26.97: [22677]: --> [7:CONNECT]
Feb 07 11:44:26.97: [22677]: DELAY 400 ms
Feb 07 11:44:27.37: [22677]: <-- data [1024]
Feb 07 11:44:27.37: [22677]: <-- data [1024]
Feb 07 11:44:27.37: [22677]: <-- data [652]
Feb 07 11:44:27.37: [22677]: <-- data [2]
Feb 07 11:44:30.14: [22677]: --> [2:OK]
Feb 07 11:44:30.14: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:44:30.52: [22677]: --> [7:CONNECT]
Feb 07 11:44:31.57: [22677]: --> [10:NO CARRIER]
Feb 07 11:44:31.57: [22677]: MODEM No carrier
Feb 07 11:44:31.57: [22677]: DELAY 1500 ms
Feb 07 11:44:33.07: [22677]: SEND training at v.17 12000 bit/s
Feb 07 11:44:33.07: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:44:34.03: [22677]: --> [7:CONNECT]
Feb 07 11:44:34.03: [22677]: <-- data [23]
Feb 07 11:44:34.03: [22677]: <-- data [2]
Feb 07 11:44:34.06: [22677]: --> [7:CONNECT]
Feb 07 11:44:34.06: [22677]: <-- data [6]
Feb 07 11:44:34.06: [22677]: <-- data [2]
Feb 07 11:44:35.20: [22677]: --> [2:OK]
Feb 07 11:44:35.20: [22677]: <-- [9:AT+FTS=7\r]
Feb 07 11:44:35.26: [22677]: --> [2:OK]
Feb 07 11:44:35.26: [22677]: <-- [11:AT+FTM=121\r]
Feb 07 11:44:35.28: [22677]: --> [7:CONNECT]
Feb 07 11:44:35.28: [22677]: DELAY 400 ms
Feb 07 11:44:35.68: [22677]: <-- data [1024]
Feb 07 11:44:35.68: [22677]: <-- data [1024]
Feb 07 11:44:35.68: [22677]: <-- data [202]
Feb 07 11:44:35.68: [22677]: <-- data [2]
Feb 07 11:44:38.45: [22677]: --> [2:OK]
Feb 07 11:44:38.45: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:44:39.34: [22677]: --> [7:CONNECT]
Feb 07 11:44:40.24: [22677]: --> [10:NO CARRIER]
Feb 07 11:44:40.24: [22677]: MODEM No carrier
Feb 07 11:44:40.24: [22677]: DELAY 1500 ms
Feb 07 11:44:41.74: [22677]: SEND training at v.17 9600 bit/s
Feb 07 11:44:41.74: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:44:42.71: [22677]: --> [7:CONNECT]
Feb 07 11:44:42.71: [22677]: <-- data [23]
Feb 07 11:44:42.71: [22677]: <-- data [2]
Feb 07 11:44:42.73: [22677]: --> [7:CONNECT]
Feb 07 11:44:42.73: [22677]: <-- data [6]
Feb 07 11:44:42.73: [22677]: <-- data [2]
Feb 07 11:44:43.87: [22677]: --> [2:OK]
Feb 07 11:44:43.87: [22677]: <-- [9:AT+FTS=7\r]
Feb 07 11:44:43.94: [22677]: --> [2:OK]
Feb 07 11:44:43.94: [22677]: <-- [10:AT+FTM=97\r]
Feb 07 11:44:43.95: [22677]: --> [7:CONNECT]
Feb 07 11:44:43.95: [22677]: DELAY 400 ms
Feb 07 11:44:44.35: [22677]: <-- data [1024]
Feb 07 11:44:44.35: [22677]: <-- data [776]
Feb 07 11:44:44.35: [22677]: <-- data [2]
Feb 07 11:44:47.12: [22677]: --> [2:OK]
Feb 07 11:44:47.12: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:44:47.42: [22677]: --> [7:CONNECT]
Feb 07 11:44:48.60: [22677]: --> [5:ERROR]
Feb 07 11:44:48.60: [22677]: MODEM Command error
Feb 07 11:44:48.60: [22677]: FCS error
Feb 07 11:44:48.60: [22677]: DELAY 1500 ms
Feb 07 11:44:50.10: [22677]: SEND training at v.29 9600 bit/s
Feb 07 11:44:50.10: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:44:51.07: [22677]: --> [7:CONNECT]
Feb 07 11:44:51.07: [22677]: <-- data [23]
Feb 07 11:44:51.07: [22677]: <-- data [2]
Feb 07 11:44:51.09: [22677]: --> [7:CONNECT]
Feb 07 11:44:51.09: [22677]: <-- data [6]
Feb 07 11:44:51.09: [22677]: <-- data [2]
Feb 07 11:44:52.24: [22677]: --> [2:OK]
Feb 07 11:44:52.24: [22677]: <-- [9:AT+FTS=7\r]
Feb 07 11:44:52.30: [22677]: --> [2:OK]
Feb 07 11:44:52.30: [22677]: <-- [10:AT+FTM=96\r]
Feb 07 11:44:52.57: [22677]: --> [7:CONNECT]
Feb 07 11:44:52.57: [22677]: DELAY 400 ms
Feb 07 11:44:52.97: [22677]: <-- data [1024]
Feb 07 11:44:52.97: [22677]: <-- data [776]
Feb 07 11:44:52.97: [22677]: <-- data [2]
Feb 07 11:44:54.54: [22677]: --> [2:OK]
Feb 07 11:44:54.54: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:44:55.77: [22677]: --> [7:CONNECT]
Feb 07 11:44:56.97: [22677]: --> [2:OK]
Feb 07 11:44:56.97: [22677]: SEND training at v.29 7200 bit/s
Feb 07 11:44:56.97: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:44:57.94: [22677]: --> [7:CONNECT]
Feb 07 11:44:57.94: [22677]: <-- data [23]
Feb 07 11:44:57.94: [22677]: <-- data [2]
Feb 07 11:44:57.96: [22677]: --> [7:CONNECT]
Feb 07 11:44:57.96: [22677]: <-- data [6]
Feb 07 11:44:57.96: [22677]: <-- data [2]
Feb 07 11:44:59.11: [22677]: --> [2:OK]
Feb 07 11:44:59.11: [22677]: <-- [9:AT+FTS=7\r]
Feb 07 11:44:59.17: [22677]: --> [2:OK]
Feb 07 11:44:59.17: [22677]: <-- [10:AT+FTM=72\r]
Feb 07 11:44:59.19: [22677]: --> [7:CONNECT]
Feb 07 11:44:59.19: [22677]: DELAY 400 ms
Feb 07 11:44:59.59: [22677]: <-- data [1024]
Feb 07 11:44:59.59: [22677]: <-- data [326]
Feb 07 11:44:59.59: [22677]: <-- data [2]
Feb 07 11:45:01.16: [22677]: --> [2:OK]
Feb 07 11:45:01.16: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:45:02.71: [22677]: --> [7:CONNECT]
Feb 07 11:45:03.91: [22677]: --> [2:OK]
Feb 07 11:45:03.91: [22677]: SEND training at v.27ter 4800 bit/s
Feb 07 11:45:03.91: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:45:04.87: [22677]: --> [7:CONNECT]
Feb 07 11:45:04.87: [22677]: <-- data [23]
Feb 07 11:45:04.87: [22677]: <-- data [2]
Feb 07 11:45:04.90: [22677]: --> [7:CONNECT]
Feb 07 11:45:04.90: [22677]: <-- data [6]
Feb 07 11:45:04.90: [22677]: <-- data [2]
Feb 07 11:45:06.04: [22677]: --> [2:OK]
Feb 07 11:45:06.04: [22677]: <-- [9:AT+FTS=7\r]
Feb 07 11:45:06.10: [22677]: --> [2:OK]
Feb 07 11:45:06.10: [22677]: <-- [10:AT+FTM=48\r]
Feb 07 11:45:06.12: [22677]: --> [7:CONNECT]
Feb 07 11:45:06.12: [22677]: DELAY 400 ms
Feb 07 11:45:06.52: [22677]: <-- data [900]
Feb 07 11:45:06.52: [22677]: <-- data [2]
Feb 07 11:45:08.61: [22677]: --> [2:OK]
Feb 07 11:45:08.61: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:45:09.67: [22677]: --> [7:CONNECT]
Feb 07 11:45:10.87: [22677]: --> [2:OK]
Feb 07 11:45:10.87: [22677]: SEND training at v.27ter fallback mode 2400 bit/s
Feb 07 11:45:10.87: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:45:11.83: [22677]: --> [7:CONNECT]
Feb 07 11:45:11.83: [22677]: <-- data [23]
Feb 07 11:45:11.83: [22677]: <-- data [2]
Feb 07 11:45:11.86: [22677]: --> [7:CONNECT]
Feb 07 11:45:11.86: [22677]: <-- data [6]
Feb 07 11:45:11.86: [22677]: <-- data [2]
Feb 07 11:45:13.00: [22677]: --> [2:OK]
Feb 07 11:45:13.00: [22677]: <-- [9:AT+FTS=7\r]
Feb 07 11:45:13.06: [22677]: --> [2:OK]
Feb 07 11:45:13.06: [22677]: <-- [10:AT+FTM=24\r]
Feb 07 11:45:13.08: [22677]: --> [7:CONNECT]
Feb 07 11:45:13.08: [22677]: DELAY 400 ms
Feb 07 11:45:13.48: [22677]: <-- data [450]
Feb 07 11:45:13.48: [22677]: <-- data [2]
Feb 07 11:45:15.81: [22677]: --> [2:OK]
Feb 07 11:45:15.81: [22677]: <-- [9:AT+FRH=3\r]
Feb 07 11:45:16.48: [22677]: --> [7:CONNECT]
Feb 07 11:45:17.68: [22677]: --> [2:OK]
Feb 07 11:45:17.68: [22677]: TRAINING failed
Feb 07 11:45:17.68: [22677]: <-- [9:AT+FTH=3\r]
Feb 07 11:45:18.64: [22677]: --> [7:CONNECT]
Feb 07 11:45:18.64: [22677]: <-- data [3]
Feb 07 11:45:18.64: [22677]: <-- data [2]
Feb 07 11:45:19.03: [22677]: --> [2:OK]
Feb 07 11:45:19.03: [22677]: SEND FAILED: JOB 42 DEST 7038168824 ERR Failure to train remote modem at 2400 bps or minimum speed; too many attempts to dial
Feb 07 11:45:19.03: [22677]: <-- [5:ATH0\r]
Feb 07 11:45:19.38: [22677]: --> [2:OK]
Feb 07 11:45:19.38: [22677]: SESSION END

[root@silver ~]# cat /etc/hylafax/etc/config.ttyS49
# $Id: lucent,v 1.19 2004/06/01 21:34:39 lhoward Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# prototype config for Lucent LT Winmodem using ltmodem.o driver,
# as well as many other Lucent chipset modems.
# (They work well with all default Class 1 configs.)
#

#
CountryCode:            1
AreaCode:               703
FAXNumber:              +1.999.555.1212
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#

ModemType: Class1 # use this to supply a hint
ModemFlowControl: rtscts # many firmwares have broken software flow control
Class1TCFRecvHack: yes # avoid +FCERROR before TCF
# Class1MsgRecvHackCmd: AT+FRS=1 # avoid +FCERROR before image
Class1TMConnectDelay: 400 # counteract quick CONNECT response

# If your line supports Caller-ID, you may want to uncomment this...
# QualifyCID:           etc/cid         # you must create this file
# ModemResetCmds:       AT+VCID=1
# CIDNumber:            "NMBR="
# CIDName:              "NAME="

# Or with the MT5634ZBA-DID you'll probably need something like...
# ModemReadyCmds: AT*DS1*DD0*DF1*DN4 # enable DTMF-DID, wink-start, 4 digits
# CIDNumber: "DTMF" # format of AT*DF1
# CIDNumberAnswerLength: 4 # four DTMF-DID digits then ATA



CLASS 1.0 ******************************************


[root@silver ~]# tail -f /etc/hylafax/log/c000000042
Feb 07 11:47:58.94: [22924]: SESSION BEGIN 000000042 17037038168824
Feb 07 11:47:58.94: [22924]: HylaFAX (tm) Version 4.2.0
Feb 07 11:47:58.94: [22924]: SEND FAX: JOB 43 DEST 7038168824 COMMID 000000042 DEVICE '/dev/ttyS49'
Feb 07 11:47:58.94: [22924]: <-- [14:AT+FCLASS=1.0\r]
Feb 07 11:47:59.04: [22924]: --> [2:OK]
Feb 07 11:47:59.04: [22924]: DIAL 7038168824
Feb 07 11:47:59.04: [22924]: <-- [15:ATDT7038168824\r]
Feb 07 11:48:18.88: [22924]: --> [7:CONNECT]
Feb 07 11:48:20.35: [22924]: --> [2:OK]
Feb 07 11:48:20.35: [22924]: REMOTE NSF "00 00 11 80 00 8A 48 00 FF 00 80 80 80 00"
Feb 07 11:48:20.35: [22924]: NSF remote fax equipment: Canon
Feb 07 11:48:20.35: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:48:20.36: [22924]: --> [7:CONNECT]
Feb 07 11:48:20.79: [22924]: --> [2:OK]
Feb 07 11:48:20.79: [22924]: REMOTE best rate 33600 bit/s
Feb 07 11:48:20.79: [22924]: REMOTE max A4 page width (215 mm)
Feb 07 11:48:20.79: [22924]: REMOTE max unlimited page length
Feb 07 11:48:20.79: [22924]: REMOTE best vres R16 x 15.4 line/mm
Feb 07 11:48:20.79: [22924]: REMOTE best format 2-D MMR
Feb 07 11:48:20.79: [22924]: REMOTE supports T.30 Annex A, 256-byte ECM
Feb 07 11:48:20.79: [22924]: REMOTE best 20 ms/scanline
Feb 07 11:48:20.79: [22924]: USE 14400 bit/s
Feb 07 11:48:20.79: [22924]: USE 20 ms/scanline
Feb 07 11:48:20.79: [22924]: SEND file "docq/doc43.ps;41"
Feb 07 11:48:20.79: [22924]: USE A4 page width (215 mm)
Feb 07 11:48:20.79: [22924]: USE unlimited page length
Feb 07 11:48:20.79: [22924]: USE 7.7 line/mm
Feb 07 11:48:20.79: [22924]: USE 2-D MR
Feb 07 11:48:20.79: [22924]: SEND training at v.17 14400 bit/s
Feb 07 11:48:20.79: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:48:21.75: [22924]: --> [7:CONNECT]
Feb 07 11:48:21.75: [22924]: <-- data [23]
Feb 07 11:48:21.75: [22924]: <-- data [2]
Feb 07 11:48:21.76: [22924]: --> [7:CONNECT]
Feb 07 11:48:21.76: [22924]: <-- data [6]
Feb 07 11:48:21.76: [22924]: <-- data [2]
Feb 07 11:48:22.92: [22924]: --> [2:OK]
Feb 07 11:48:22.92: [22924]: <-- [9:AT+FTS=7\r]
Feb 07 11:48:22.97: [22924]: --> [2:OK]
Feb 07 11:48:22.97: [22924]: <-- [11:AT+FTM=145\r]
Feb 07 11:48:22.98: [22924]: --> [7:CONNECT]
Feb 07 11:48:22.98: [22924]: DELAY 400 ms
Feb 07 11:48:23.38: [22924]: <-- data [1024]
Feb 07 11:48:23.38: [22924]: <-- data [1024]
Feb 07 11:48:23.38: [22924]: <-- data [652]
Feb 07 11:48:23.38: [22924]: <-- data [2]
Feb 07 11:48:26.15: [22924]: --> [2:OK]
Feb 07 11:48:26.15: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:48:26.53: [22924]: --> [7:CONNECT]
Feb 07 11:48:27.72: [22924]: --> [2:OK]
Feb 07 11:48:27.72: [22924]: SEND training at v.17 12000 bit/s
Feb 07 11:48:27.72: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:48:28.68: [22924]: --> [7:CONNECT]
Feb 07 11:48:28.68: [22924]: <-- data [23]
Feb 07 11:48:28.68: [22924]: <-- data [2]
Feb 07 11:48:28.69: [22924]: --> [7:CONNECT]
Feb 07 11:48:28.69: [22924]: <-- data [6]
Feb 07 11:48:28.69: [22924]: <-- data [2]
Feb 07 11:48:29.85: [22924]: --> [2:OK]
Feb 07 11:48:29.85: [22924]: <-- [9:AT+FTS=7\r]
Feb 07 11:48:29.90: [22924]: --> [2:OK]
Feb 07 11:48:29.90: [22924]: <-- [11:AT+FTM=121\r]
Feb 07 11:48:29.91: [22924]: --> [7:CONNECT]
Feb 07 11:48:29.91: [22924]: DELAY 400 ms
Feb 07 11:48:30.31: [22924]: <-- data [1024]
Feb 07 11:48:30.31: [22924]: <-- data [1024]
Feb 07 11:48:30.31: [22924]: <-- data [202]
Feb 07 11:48:30.31: [22924]: <-- data [2]
Feb 07 11:48:33.08: [22924]: --> [2:OK]
Feb 07 11:48:33.08: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:48:33.45: [22924]: --> [7:CONNECT]
Feb 07 11:48:34.70: [22924]: --> [10:NO CARRIER]
Feb 07 11:48:34.70: [22924]: MODEM No carrier
Feb 07 11:48:34.70: [22924]: DELAY 1500 ms
Feb 07 11:48:36.20: [22924]: SEND training at v.17 9600 bit/s
Feb 07 11:48:36.20: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:48:37.16: [22924]: --> [7:CONNECT]
Feb 07 11:48:37.16: [22924]: <-- data [23]
Feb 07 11:48:37.16: [22924]: <-- data [2]
Feb 07 11:48:37.17: [22924]: --> [7:CONNECT]
Feb 07 11:48:37.17: [22924]: <-- data [6]
Feb 07 11:48:37.17: [22924]: <-- data [2]
Feb 07 11:48:38.33: [22924]: --> [2:OK]
Feb 07 11:48:38.33: [22924]: <-- [9:AT+FTS=7\r]
Feb 07 11:48:38.38: [22924]: --> [2:OK]
Feb 07 11:48:38.38: [22924]: <-- [10:AT+FTM=97\r]
Feb 07 11:48:38.39: [22924]: --> [7:CONNECT]
Feb 07 11:48:38.39: [22924]: DELAY 400 ms
Feb 07 11:48:38.79: [22924]: <-- data [1024]
Feb 07 11:48:38.79: [22924]: <-- data [776]
Feb 07 11:48:38.79: [22924]: <-- data [2]
Feb 07 11:48:41.56: [22924]: --> [2:OK]
Feb 07 11:48:41.56: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:48:41.94: [22924]: --> [7:CONNECT]
Feb 07 11:48:43.14: [22924]: --> [2:OK]
Feb 07 11:48:43.14: [22924]: SEND training at v.29 9600 bit/s
Feb 07 11:48:43.14: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:48:44.10: [22924]: --> [7:CONNECT]
Feb 07 11:48:44.10: [22924]: <-- data [23]
Feb 07 11:48:44.10: [22924]: <-- data [2]
Feb 07 11:48:44.11: [22924]: --> [7:CONNECT]
Feb 07 11:48:44.11: [22924]: <-- data [6]
Feb 07 11:48:44.11: [22924]: <-- data [2]
Feb 07 11:48:45.27: [22924]: --> [2:OK]
Feb 07 11:48:45.27: [22924]: <-- [9:AT+FTS=7\r]
Feb 07 11:48:45.32: [22924]: --> [2:OK]
Feb 07 11:48:45.32: [22924]: <-- [10:AT+FTM=96\r]
Feb 07 11:48:45.58: [22924]: --> [7:CONNECT]
Feb 07 11:48:45.58: [22924]: DELAY 400 ms
Feb 07 11:48:45.98: [22924]: <-- data [1024]
Feb 07 11:48:45.98: [22924]: <-- data [776]
Feb 07 11:48:45.98: [22924]: <-- data [2]
Feb 07 11:48:47.55: [22924]: --> [2:OK]
Feb 07 11:48:47.55: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:48:48.83: [22924]: --> [7:CONNECT]
Feb 07 11:48:50.02: [22924]: --> [2:OK]
Feb 07 11:48:50.02: [22924]: SEND training at v.29 7200 bit/s
Feb 07 11:48:50.02: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:48:50.98: [22924]: --> [7:CONNECT]
Feb 07 11:48:50.98: [22924]: <-- data [23]
Feb 07 11:48:50.98: [22924]: <-- data [2]
Feb 07 11:48:50.99: [22924]: --> [7:CONNECT]
Feb 07 11:48:50.99: [22924]: <-- data [6]
Feb 07 11:48:50.99: [22924]: <-- data [2]
Feb 07 11:48:52.14: [22924]: --> [2:OK]
Feb 07 11:48:52.15: [22924]: <-- [9:AT+FTS=7\r]
Feb 07 11:48:52.20: [22924]: --> [2:OK]
Feb 07 11:48:52.20: [22924]: <-- [10:AT+FTM=72\r]
Feb 07 11:48:52.21: [22924]: --> [7:CONNECT]
Feb 07 11:48:52.21: [22924]: DELAY 400 ms
Feb 07 11:48:52.61: [22924]: <-- data [1024]
Feb 07 11:48:52.61: [22924]: <-- data [326]
Feb 07 11:48:52.61: [22924]: <-- data [2]
Feb 07 11:48:54.18: [22924]: --> [2:OK]
Feb 07 11:48:54.18: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:48:55.70: [22924]: --> [7:CONNECT]
Feb 07 11:48:56.90: [22924]: --> [2:OK]
Feb 07 11:48:56.90: [22924]: SEND training at v.27ter 4800 bit/s
Feb 07 11:48:56.90: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:48:57.85: [22924]: --> [7:CONNECT]
Feb 07 11:48:57.85: [22924]: <-- data [23]
Feb 07 11:48:57.85: [22924]: <-- data [2]
Feb 07 11:48:57.86: [22924]: --> [7:CONNECT]
Feb 07 11:48:57.86: [22924]: <-- data [6]
Feb 07 11:48:57.86: [22924]: <-- data [2]
Feb 07 11:48:59.02: [22924]: --> [2:OK]
Feb 07 11:48:59.02: [22924]: <-- [9:AT+FTS=7\r]
Feb 07 11:48:59.08: [22924]: --> [2:OK]
Feb 07 11:48:59.08: [22924]: <-- [10:AT+FTM=48\r]
Feb 07 11:48:59.08: [22924]: --> [7:CONNECT]
Feb 07 11:48:59.08: [22924]: DELAY 400 ms
Feb 07 11:48:59.48: [22924]: <-- data [900]
Feb 07 11:48:59.48: [22924]: <-- data [2]
Feb 07 11:49:01.58: [22924]: --> [2:OK]
Feb 07 11:49:01.58: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:49:02.57: [22924]: --> [7:CONNECT]
Feb 07 11:49:03.86: [22924]: --> [5:ERROR]
Feb 07 11:49:03.86: [22924]: MODEM Command error
Feb 07 11:49:03.86: [22924]: FCS error
Feb 07 11:49:03.86: [22924]: DELAY 1500 ms
Feb 07 11:49:05.35: [22924]: SEND training at v.27ter fallback mode 2400 bit/s
Feb 07 11:49:05.36: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:49:06.31: [22924]: --> [7:CONNECT]
Feb 07 11:49:06.31: [22924]: <-- data [23]
Feb 07 11:49:06.31: [22924]: <-- data [2]
Feb 07 11:49:06.32: [22924]: --> [7:CONNECT]
Feb 07 11:49:06.32: [22924]: <-- data [6]
Feb 07 11:49:06.32: [22924]: <-- data [2]
Feb 07 11:49:07.48: [22924]: --> [2:OK]
Feb 07 11:49:07.48: [22924]: <-- [9:AT+FTS=7\r]
Feb 07 11:49:07.54: [22924]: --> [2:OK]
Feb 07 11:49:07.54: [22924]: <-- [10:AT+FTM=24\r]
Feb 07 11:49:07.54: [22924]: --> [7:CONNECT]
Feb 07 11:49:07.54: [22924]: DELAY 400 ms
Feb 07 11:49:07.94: [22924]: <-- data [450]
Feb 07 11:49:07.94: [22924]: <-- data [2]
Feb 07 11:49:10.28: [22924]: --> [2:OK]
Feb 07 11:49:10.28: [22924]: <-- [9:AT+FRH=3\r]
Feb 07 11:49:10.84: [22924]: --> [7:CONNECT]
Feb 07 11:49:12.04: [22924]: --> [2:OK]
Feb 07 11:49:12.04: [22924]: TRAINING failed
Feb 07 11:49:12.04: [22924]: <-- [9:AT+FTH=3\r]
Feb 07 11:49:12.99: [22924]: --> [7:CONNECT]
Feb 07 11:49:12.99: [22924]: <-- data [3]
Feb 07 11:49:12.99: [22924]: <-- data [2]
Feb 07 11:49:13.38: [22924]: --> [2:OK]
Feb 07 11:49:13.38: [22924]: SEND FAILED: JOB 43 DEST 7038168824 ERR Failure to train remote modem at 2400 bps or minimum speed; too many attempts to dial
Feb 07 11:49:13.38: [22924]: <-- [5:ATH0\r]
Feb 07 11:49:13.73: [22924]: --> [2:OK]
Feb 07 11:49:13.73: [22924]: SESSION END


[root@silver ~]# cat /etc/hylafax/etc/config.ttyS49
# $Id: lucent-mt-10,v 1.4 2004/06/01 21:34:39 lhoward Exp $

#
# prototype config for MultiTech 5634-series modems using
# the Lucent/Agere chipset supporting V.34-Fax.
#

#
CountryCode:            1
AreaCode:               703
FAXNumber:              +1.999.555.1212
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#

ModemType: Class1.0 # use this to supply a hint
ModemRate: 57600 # must be at least as fast as the DCE-DCE communication
ModemFlowControl: rtscts # many firmwares have broken software flow control
Class1EnableV34Cmd: AT+F34=14,1,2 # 33600-2400 primary, 2400-1200 control
Class1TCFRecvHack: yes # avoid +FCERROR before TCF
Class1TMConnectDelay: 400 # counteract quick CONNECT response

# If your line supports Caller-ID, you may want to uncomment this...
# QualifyCID:           etc/cid         # you must create this file
# ModemResetCmds:       AT+VCID=1
# CIDNumber:            "NMBR="
# CIDName:              "NAME="

# Or with the MT5634ZBA-DID you'll probably need something like...
# ModemReadyCmds: AT*DS1*DD0*DF1*DN4 # enable DTMF-DID, wink-start, 4 digits
# CIDNumber: "DTMF" # format of AT*DF1
# CIDNumberAnswerLength: 4 # four DTMF-DID digits then ATA


Lee Howard wrote:

Please try Class 1 or Class 1.0 and try again.

Lee.


On 2005.02.07 13:42 Peter Halliday wrote:

I have purchases a multitech ISI card modem it was recognized as MT5634SMI-V92/1.32b. I was testing it and this is the output. I know it's bad, but not sure what's going on here. I have listed the configuration below as well.

Thanks ahead of time

Peter Halliday

[root@silver ~]# tail -f /etc/hylafax/log/c000000004
Jan 13 02:55:10.46: [ 4303]: <-- [23:AT+FCC=1,5,2,2,3,1,0,0\r]
Jan 13 02:55:10.58: [ 4303]: --> [2:OK]
Jan 13 02:55:10.58: [ 4303]: DIAL 7038168824
Jan 13 02:55:10.58: [ 4303]: <-- [30:AT+FCC=,,,,,,,,0;DT7038168824\r]
Jan 13 02:55:21.11: [ 4303]: --> [11:NO DIALTONE]
Jan 13 02:55:21.11: [ 4303]: SEND FAILED: JOB 4 DEST 7038168824 ERR No local dialtone
Jan 13 02:55:21.11: [ 4303]: SEND FAILED: JOB 4 DEST 7038168824 ERR No local dialtone; too many attempts to dial
Jan 13 02:55:21.11: [ 4303]: <-- [5:ATH0\r]
Jan 13 02:55:21.34: [ 4303]: --> [2:OK]
Jan 13 02:55:21.34: [ 4303]: SESSION END

[root@silver ~]# tail -f /etc/hylafax/log/c000000040
Feb 07 10:19:58.29: [22351]: <-- [15:AT+FNR=1,1,1,1\r]
Feb 07 10:19:58.41: [22351]: --> [2:OK]
Feb 07 10:19:58.41: [22351]: <-- [13:AT+FAP=1,1,1\r]
Feb 07 10:19:58.52: [22351]: --> [2:OK]
Feb 07 10:19:58.52: [22351]: <-- [9:AT+FIE=0\r]
Feb 07 10:19:58.63: [22351]: --> [2:OK]
Feb 07 10:19:58.63: [22351]: <-- [23:AT+FCC=1,5,2,2,3,1,0,0\r]
Feb 07 10:19:58.75: [22351]: --> [2:OK]
Feb 07 10:19:58.75: [22351]: DIAL 7038168824
Feb 07 10:19:58.75: [22351]: <-- [30:AT+FCC=,,,,,,,,0;DT7038168824\r]
Feb 07 10:20:21.11: [22351]: --> [4:+FCO]
Feb 07 10:20:21.11: [22351]: --> [46:+FNF:00 00 11 80 00 8A 48 00 FF 00 80 80 80 00]
Feb 07 10:20:21.11: [22351]: REMOTE NSF "00 00 11 80 00 8A 48 00 FF 00 80 80 80 00"
Feb 07 10:20:21.11: [22351]: NSF remote fax equipment: Canon
Feb 07 10:20:21.53: [22351]: --> [20:+FIS:1,5,0,2,7,1,0,5]
Feb 07 10:20:21.53: [22351]: --> [2:OK]
Feb 07 10:20:21.53: [22351]: REMOTE best rate 14400 bit/s
Feb 07 10:20:21.53: [22351]: REMOTE max A4 page width (215 mm)
Feb 07 10:20:21.53: [22351]: REMOTE max unlimited page length
Feb 07 10:20:21.53: [22351]: REMOTE best vres 7.7 line/mm
Feb 07 10:20:21.53: [22351]: REMOTE best format 2-D MMR
Feb 07 10:20:21.53: [22351]: REMOTE supports T.30 Annex A, 256-byte ECM
Feb 07 10:20:21.53: [22351]: REMOTE best 20 ms/scanline
Feb 07 10:20:21.53: [22351]: USE 14400 bit/s
Feb 07 10:20:21.53: [22351]: USE 20 ms/scanline
Feb 07 10:20:21.53: [22351]: SEND file "docq/doc41.ps;41"
Feb 07 10:20:21.53: [22351]: USE A4 page width (215 mm)
Feb 07 10:20:21.53: [22351]: USE unlimited page length
Feb 07 10:20:21.53: [22351]: USE 7.7 line/mm
Feb 07 10:20:21.53: [22351]: USE 2-D MR
Feb 07 10:20:21.53: [22351]: <-- [23:AT+FIS=1,5,0,2,1,0,0,5\r]
Feb 07 10:20:21.65: [22351]: --> [2:OK]
Feb 07 10:20:21.65: [22351]: <-- [7:AT+FDT\r]
Feb 07 10:21:21.63: [22351]: --> [7:+FHS:25]
Feb 07 10:21:21.87: [22351]: --> [2:OK]
Feb 07 10:21:21.87: [22351]: <-- [7:AT+FDT\r]
Feb 07 10:21:21.98: [22351]: --> [5:ERROR]
Feb 07 10:21:21.98: [22351]: <-- [7:AT+FKS\r]
Feb 07 10:21:22.10: [22351]: --> [6:+FHS:2]
Feb 07 10:21:22.10: [22351]: REMOTE HANGUP: Call aborted, from +FK or <CAN> (code 2)
Feb 07 10:21:22.10: [22351]: MODEM Hang up
Feb 07 10:21:22.10: [22351]: SEND FAILED: JOB 41 DEST 7038168824 ERR Communication failure during Phase B/C; too many attempts to dial
Feb 07 10:21:22.10: [22351]: <-- [5:ATH0\r]
Feb 07 10:21:22.10: [22351]: --> [2:OK]
Feb 07 10:21:22.10: [22351]: SESSION END

[root@silver ~]# cat /etc/hylafax/etc/config.ttyS49
# $Id: lucent-mt-20,v 1.13 2004/06/01 21:34:39 lhoward Exp $
#
# prototype config file for MultiTech MT5634ZBA-V.92-NAM
#

#
#
CountryCode:            1
AreaCode:               703
FAXNumber:              +1.999.555.1212
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#

ModemType:              Class2.0
ModemRate:              19200
ModemNoFlowCmd:         AT&K0
ModemSoftFlowCmd:       AT&K4
ModemHardFlowCmd:       AT&K3

Class2APCmd: AT+FAP=1,1,1
Class2BUGCmd: AT+FBU=0 # early firmware is buggy
Class2SendRTC: yes
Class2UseHex: yes

# Some firmwares do not report copy quality correction, although it
# is present and cannot be disabled.  Thus modem-based CQ must be used.
Class2CQQueryCmd:       "!(00-02),(00-02)"
Class2CQCmd:            AT+FCQ=1,0

# versions that respond to AT+FFC=? with non-zero data support RTFCC
# Class2RTFCC:          yes

# unfortunately, HylaFAX can't currently send or receive in color
ModemAnswerCmd:         AT+FCC=,,,,,,,,0;A
ModemDialCmd:           AT+FCC=,,,,,,,,0;DT%s

# Some firmware revisions (i.e. 1.25 in ZBAs) report MMR support but
# corrupt the data. Enabling the following lines should work around this.
# Compare this against the modem's AT+FCC=? response.
# Class2DCCQueryCmd: "!(00-01),(00-05),(00-02),(00-02),(00-01),(00-01),(00),(00-07)"
# ModemAnswerCmd: AT+FCC=,,,,1,,,,0;A
# ModemDialCmd: AT+FCC=,,,,1,,,,0;DT%s

# If your modem supports ECM you may want to do something like this
# Class2Cmd:            AT+FCLASS=2.0;+FRY=4

# If your line supports Caller-ID, you may want to uncomment this...
# QualifyCID:           etc/cid         # you must create this file
# ModemResetCmds:       AT+VCID=1
# CIDNumber:            "NMBR="
# CIDName:              "NAME="

# Or with the MT5634ZBA-DID you'll probably need something like...
# ModemReadyCmds: AT*DS1*DD0*DF1*DN4 # enable DTMF-DID, wink-start, 4 digits
# CIDNumber: "DTMF" # format of AT*DF1
# CIDNumberAnswerLength: 4 # four DTMF-DID digits then ATA





____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx* 






____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Project hosted by iFAX Solutions